Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

MODEL 26-CRR

CHAIN DRIVEN LIVE ROLLER CONVEYOR
(Roll-to-Roll Type)

chain driven live roller conveyor
The heavy design of the 26-CRR
allows it to be used for conveying
higher load capacities such as loaded
pallets and drums. Chain driven rollers
make it ideal for conveying oily parts
in bottling and steel industries.
• 15 Bed Widths
• Center Drive
• Reversible
• Chain Driven Rollers
• Adjustable HSN-Type Floor Supports
   Available

conveyors
STANDARD SPECIFICATIONS
BED - with No. 40 roller chain; 5 in. with No. 50 roller
chain. No. 60 roller chain used on 3 in., 3-3/4 in., 6 in.,
and 7-1/2 in. roller centers only. Tread rollers mounted
in 4 in. x 4 ga. powder painted formed steel channel on
side opposite chain guard and 6 in. x 4 ga. powder
painted formed steel channel on chain guard side.
NOTE: 3 in. roller center tread rollers mounted in 4 in.
channel each side.
BEARINGS–Sealed, pre-lubricated ball bearings.
SPEED REDUCTION–Sealed worm gear C-Face
speed reducer.
MOTOR–1 HP–208/230/460/575V–3 Ph. 60 Hz.
Totally Enclosed C-Face.
CONVEYING SPEED–Constant 30 FPM.
CAPACITY–Maximum load per linear foot of conveyor
300 lbs. with supports on 10 ft. centers, 1000 lbs. with
supports on 5 ft. centers. Contact us for capacity of
No. 40 chain, 4 in. roller centers. NOT TO EXCEED
CAPACITY IN CHART.
CENTER DRIVE- Can be placed in any section of
conveyor length, specify. Chain guard located on left
hand side.
DRIVE CHAIN–No. 40, 50 or 60 roller chain.
FLOOR SUPPORTS–Now supplied as optional
equipment.
CHAIN GUARD–Formed steel, upper and lower
chain guard mounted to top and bottom of channel
frame to totally enclose drive chains.
chain guard
LOAD CAPACITY CHART @ 30 FPM
HP
TOTAL LOAD (LBS.)
UP TO 50'
UP TO 100'
1
9000
6000
2
22000
18000
NOTE: Capacities are calculated on 5" Roller Centers with
#50 Chain.

OPTIONAL EQUIPMENT
FLOOR SUPPORTS–HSN Type floor supports are
available with a wide range of adjustment. Specify top or
roller elevation. One support required at every bed joint
and ends of conveyor. Holes in feet for lagging to floor.
Knee braces recommended above HSN-3 support.
CHANNEL END STOP–6” x 8.2 lb. structural channel
end stop.
ROLLERS SET LOW–Tread rollers mounted in 6 in.
x 4 ga. formed steel channel frame to form 1-5/8 in. high
guard rails. Also available in 5 in. x 6.7 lbs. structural
channel frame (welded). Specify.
CONVEYING SPEED–Other constant and variable
speeds. V-belt supplied on speeds under 12 FPM (1 HP).
NOTE: Capacity affected with speed change.
CHAIN CROSSOVER–Separate 3-roller section
moves driving chain from one side of conveyor to other.
Offset-style adds 12 in. to OAL of conveyor with No.
40 chain, 15 in. with No. 50 chain & 18 in. with No.60
chain.
TOP SIDE MOUNTED DRIVE–Motor reducer unit
mounted to side of conveyor with drive chain through top
of chain guard. Specify clearances. Minimum elevation top
of rollers 6 in.
TRANSFERS–Chain transfers available. See Acces-
sory section.
V-BELT DRIVE–V-belt supplied between motor and
reducer.
MOTORS–Energy efficient, single phase, brake motor,
other characteristics. 2 HP maximum.
O-RING DRIVE CHAIN–With sealed in lubricant
(Recommended for applications that do not permit regular
lubrication).
ELECTRICAL CONTROLS–Non-reversing
magnetic starter – pushbutton stations. AC variable
frequency drive.
FRAMES–4 in. x 5.4 lb. structural channel.
GUARD RAILS–Fixed angle (2 in. high x 1/4 in. steel)
guard bolts to top flange of channel opposite chain guard.

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


PRICES FOR COMPLETE CONVEYOR INCLUDE:
• 2-5/8” Dia. x 7 Ga. Roller Mounted in a 4” x 4 Ga. Formed Channel Frame
• No. 40 *, No. 50, or No. 60 Roller Chain
• “C” Face Speed Reducer—Sealed Worm Gear
• 1 HP–“C” Face Totally Enclosed Motor (Specify Exact Voltage)
• Totally Enclosed Chain Guard
• 30 FPM Conveying Speed
• Less Electrical Controls
• Less Supports
4 in., 5 in., 6 in. and 7-1/2 in. Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 19" 21" 23" 25" 27" 31" 33" 37" 39" 43" 47" 51" 55" 61" 67"
Overall Frame Width 22-1/4" 24-1/4" 26-1/4" 28-1/4 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
*4" Centers 10' Length-
O.A. Per Foot
No. 40 Chain
5" Centers 10' Length-
OA Per Foot
No. 50 Chain
6" Centers 10' Length-
OA Per Foot
No. 60 Chain
7-1/2" Centers 10' Length-
OA Per Foot
No. 60 Chain
3 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22-1/4" 24-1/4" 26-1/4" 28-1/4" 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4" 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
Overall Frame Width 25-1/2" 27-1/2" 29-1/2" 31-1/2" 33-1/2" 37-1/2" 39-1/2" 43-1/2" 45-1/2" 49-1/2" 53-1/2" 57-1/2" 61-1/2" 67-1/2" 73-1/2"
3" Centers 10' Length-
OA Per Foot
No. 60 Chain
3 3/4 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22" 24" 26" 28" 30" 34" 36" 40" 42" 46" 50" 54" 58" 64" 70"
Overall Frame Width 25-1/4" 27-1/4" 29-1/4" 31-1/4" 33-1/4" 37-1/4" 39-1/4" 43-1/4" 45-1/4" 49-1/4" 53-1/4" 57-1/4" 61-1/4" 67-1/4" 73-1/4"
3 3/4" Centers 10' Length
OA Per Foot
No. 60 Chain
*No. 40 Chain reduces total conveyor capacity.
IMPORTANT NOTES

• OTHER LENGTHS
   For longer or shorter than 10’ Overall Length, add or deduct PER FOOT from 10’ price. NO DEDUCT for unit
   less than 5’.
• OTHER WIDTHS
   For “IN-BETWEEN WIDTHS”, use next width plus 10%. For widths up to 74-1/4” OAW, interpolate plus 10%.
   For widths over 74-1/4” OAW, contact us for lead time.
• INTERMEDIATE BEDS
  Use per foot price of width x required length, supports not included.
• FLOOR SUPPORTS
  Floor Supports are not included in base price. There are two (2) stationary floor supports required for the first
  bed section and one (1) support required per bed section thereafter.
• NON-STANDARD WIDTHS
  Contact us for lead time.


Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


PRICES FOR OPTIONAL EQUIPMENT
MOTORS
Extra Motor Price for OTHER THAN: 1 HP-208/230/460/575 V-3 Ph.-60 Hz.-Totally Enclosed. Speed affects
horsepower requirements.
H.P. REQ.
TOTALLY ENCLOSED
ENERGY EFFICIENT
200/208/230/460/575V 3Ph-60Hz.
115/230V 1Ph-60Hz
1
N/C $83.60
2
$936.80 $1,142.20
FLOOR SUPPORTS DRIVE COMPONENT DEDUCTS
Not Included in Base Price. Use Chart Below for
Required Elevation.
Less Complete Motor Drive and Drive Shell (For
Slave Driving) ........... Deduct.................... $982.00
Model No. Adjustment to
Top of Roller
Price Up to
73 1/4" OAW
Price Above
74 1/4" OAW
HSN-1** 10-1/2" to 12"
HSN-2** 12" to 15"
HSN-3** 15" to 18"
HSN-4* 18" to 21"
HSN-5* 21" to 24"
HSN-6* 24" to 30"
HSN-7* 30" to 36"
HSN-8* 36" to 48"
HSN-9* 48" to 60"
HSN-10* 60" to 72"
HSN-11* 72" to 84"
HSN-12* 84" to 96"
Less Motor Only (1 HP-208/230/460/575 V-3
Ph.-60 Hz.) ............... Deduct .................. $282.90
Less Reducer* (4A or 4AC) Deduct ........ $307.40
*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less
chain guard and sprockets when C-Face drive is
supplied.
GUARD RAILS
Angle Type “A”
2” x 1-5/8” x 1/4”
Side Opposite Chain Guard ... per foot ..... $11.40
CONSTANT AND VARIABLE SPEEDS
Constant C-Face–Within 13-100 FPM .No Charge
Constant V-Belt–Within 4-12 FPM .....................
............................... Use V-Belt Drive Add-on
* Knee Braces (Included in support price)
   Extra Braces ......Add per pair ................... $72.80
OPTIONAL FRAME
**Less than 18-1/2” top of roller elevation–
   Top Side Mounted Drive Required.
6” x 1-5/8” x 4 Ga. Formed Channel Set Low .....
............................... add on per foot ........ $5.70
4” x 5.4 lbs. Structural Channel ........................
OPTIONAL DRIVE
............................... add on per foot ........ $13.50
Drive
Type
Overall Frame Width
22-1/4" to
34-1/4"
36-1/4"
to 54-1/4"
58-1/4"
to 70-1/4"
Top Side
Mounted C-Face
Top Side
Mounted V-Belt
5” x 6.7 lbs. Structural Channel Set Low .............
............................... add on per foot ........ $17.30
6” x 8.2 lbs. Structural Channel Set Low .............
............................... add on per foot ........ $32.60
HEAVY DUTY END STOP (SET HIGH ONLY)
6” x 8.2 lbs. structural channel
#50 O-Ring Drive Chain ......... Add ......... $284.40 19” - 43” BR ............................................ $100.20
#60 O-Ring Drive Chain ......... Add ......... $406.00 45” - 67” BR ............................................ $146.40
Under 5’ -0” OAL use Top Side Mounted or V-Belt Drive.
V-Belt Drive. 3'-0" and under use V-Belt Drive ONLY. HEAVY DUTY END STOP (SET LOW ONLY)
7” x 9.8 lbs. structural channel
ELECTRICAL CONTROLS
19” - 43” BR ............................................ $146.50
See below.
45” - 67” BR ............................................ $222.80
GALVANIZING CHAIN CROSSOVER
Contact us. Off-Set Style “C” or “D” .......................... $1,015.40
chain crossover
OPTIONAL ROLLERS
Use the following Add-on prices for optional
roller centers and bearings.
Regreasable Bearings with Grease Fittings
3” Roller Centers ....... Add-on per foot ... $165.80
3-3/4” Roller Centers .. Add-on per foot .. $132.60
4” Roller Centers ....... Add-on per foot .... $124.30
5” Roller Centers ....... Add-on per foot .... $99.40
6” Roller Centers ....... Add-on per foot .... $83.00
7-1/2” Roller Centers .. Add-on per foot ... $66.40
ANGLE END STOP
2” x 2” x 4 Ga.
19” - 23” BR ...........................................
$42.60
25” - 39” BR ............................................ $56.10
43” - 67” BR ............................................ $82.90
2-5/8" x .219 Wall with 013.1059 Heavy Duty Bearings
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
3" Centers Add on Per Foot
3-3/4" Centers Add on Per Foot
4" Centers Add on Per Foot
5" Centers Add on Per Foot
6" Centers Add on Per Foot
7-1/2" Centers Add on Per Foot

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


ELECTRICAL CONTROLS AND DRIVE SECTION
MANUAL START SWITCH or
SAFETY DISCONNECT
limit switch LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER
manual start switch
#032.1014......................................... $213.01 #033.2032 & #033.2072..................$555.67
Nema 4
"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)
LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER
limit switch double pole

#033.2033& #033.2072...................$332.11
Nema 4
REVERSING DRUM SWITCH
#032.103.......................................... $854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase
PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range


foot swtich with guard FOOT SWITCH WITH GUARD
#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range
#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.


PHOTO EYE, ON-OFF TYPE
power cord and plug #EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC
POWER CORD AND PLUG (20')
POWER CORD WITH PLUG ONLY 20' LONG
Model No.
Voltage
HP Rating
Prices
EA-039-1A
115/1
1/2-3/4
EA-039-2A
115/1
1
EA-039-3A
115/1
1 1/2
EA-039-4A
230/1
1/2-1
EA-039-5A
230/1
1 1/2-2
EA-039-6A
208-230/3
1/2-2
EA-039-7A
460/3
1/2-2
POWER CORD WITH PLUG 20' LONG WITH MANUAL START SWITCH AND MOUNTING BRACKET
Model No.
Voltage
HP Rating
Prices
EA-039-1B
115/1
1/2-3/4
EA-039-2B
115/1
1
EA-039-3B
115/1
1 1/2
EA-039-4B
230/1
1/2-1
EA-039-5B
230/1
1 1/2-2
EA-039-6B
208-230/3
1/2-2
EA-039-7B
460/3
1/2-2
MOUNTING BRACKETS FOR PHOTO
EYE #033.2122
B-05165...........................................$118.10

AIR PRESSURE SWITCH
#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH
#032.285 with 032.2851 Turnbuckle
...........................................................
$696.08
Nema 4
"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE
#032.281...one side.................$7.44 per / ft.
                  both sides..............$15.87per / ft.
EMERGENCY PUSH BUTTON
#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE
#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48
NOTE: PRICING LISTED NOT MOUNTED
             OR WIRED
"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC
#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CONTROLLER PRICES
AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size 115 Volt 208/230 Volt
1/2 VSC-12-10 VSC-12-12
Price $1,491.84 $1,189.37
1 VSC-12-11 VSC-12-13
Price $1,724.27
2 N/A
VSC-12-14
Price ~
THREE PHASE CONTROLLER INPUT
Motor Size 208/230 Volt 460 Volt 575 Volt
1/2
VSC-01-15
VSC-01-18
VSC-12-29
Price
1
VSC-01-16
VSC-01-19
VSC-12-29
Price
2
VSC-01-17
VSC01--20
VSC-12-30
Price
REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS
HP Part No. Price
1/2 032.351 230/460
1 032.353 230/460
2 032.355 230/460
1/2 032.3512 575
1 032.3532 575
2 032.3552 575
IMPORTANT NOTES...
All above motors are 230 / 460 / 575 Volt, 3 Phase.
All above V/S Drive Kits include NEMA 1 / IP30
  Junction Box, Controller and Motor.
Good for cycle rates of up to 15 cycles per minute, at
  1/2 second ramp time, with a maximum speed of 250
  FPM.
Drawing No. DG-001146.
OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)
$675.20 When AC Variable Speed Controller is used with a
   Brake Motor, A Brake Relay Kit (EA-068A) is
   required. Add an additional $542.68 for this option.)
Brake Relay Kit (EA-068A).............................. $542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE
Part No. Description Price
EA-VSC-01-CB 2 HP Electronic Clutch-Brake Kit $5,058.00
OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)
$675.20
KIT INCLUDES
Part No. Description
VSC-01-20 AC Variable Speed Controller, 460 Volt, 3 Phase
032.345 2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
IMPORTANT NOTES
Good for cycle rates of up to 60 cycles per minute.
1/10 second Accel and Decel time, with 350 FPM
   Maximum Speed.
230 or 460 Volt Only, Other Voltages, Contact us.
Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
Price Includes 5AC Reducer and #60 Chain and
  Sprockets
Part No. Description
VSC-01-17 AC Variable Speed Controller, 230 Volt, 3 Phase
032.345 2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


starter
THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use
.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
MOTOR
DUTY
NON-REVERSING
REVERSING
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
1/2
STANDARD EASY
CLEAN ENERG. EFF.
$1516.60
$2,023.30
 
 
 
 
 
 
 
 
1
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
1-1/2
GEARMOTORS
 
 
 
 
 
 
 
 
2
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
NON-REVERSING
REVERSING
NON-REVERSING
REVERSING
 
115 VOLT
PRICE
115 VOLT
PRICE
230 VOLT
PRICE
230 VOLT
PRICE
1/2
$1,182.40
$2,023.30
$1,435.60
$2,023.30
1
1-1/2
2
• Manual Start-Stop Switch Kit • Start-Stop Push Button Kit, Remote Mounted
EA-000001 ...................................... $242.09 EA-000002....................................... $242.09
Includes: 032.1014 Manual Start Switch, Nema 1,
B-21467 Mounting Bracket with Mounting Hardware
Includes: 033.1955 Push Button Station, One
Direction, Nema1, B-21467 Mounting Bracket
with Mounting Hardware
Forward-Reverse-Stop Push Button Kit,
  Remote Mounted
• Up-Down-Stop Push Button Kit, Remote
   Mounted
EA-000003....................................... $440.67
Includes: 033.1965 Push Button Station, Reversing,
Nema1, B-21467 Mounting Bracket with Mounting
Hardware
EA-000004....................................... $440.67
Includes: 033.1975 Up Down Stop Push Button
Station, Reversing, Nema 1, B-21467 Mounting
Bracket with Mounting Hardware

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station • “Start-Stop”Push-button Station
033.1955
$211.23 033.195................................................. $142.50
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Fwd-Rev-Stop” Push-button Station • “Fwd-Rev-Stop”Push Button Station
033.1965 $397.05 033.196.................................................. $490.95
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Up-Down-Stop” Push-button Station
OPTIONAL STARTER CONTROLS
033.1975 $397.05
• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1
EA-011 ............................................
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
$3,210.68
IMPORTANT NOTES
Control Circuit Transformer Included for 115 Volt
  Control Voltage.
Above starters are in Nema 3, 4 and 12 Enclosures.
The starters included Safety Disconnect, Overload
  Relay, and Aux. Contacts as required.
IF AN ORDER IS SUPPLIED LESS MOTOR,
  AND IS SUPPLYING ANY ELECTRICAL
  CONTROLS, THEN MOTOR HP, VOLTAGE,
  PHASE, AND FULL LOAD CURRENT MUST BE
  STATED ON THE ORDER.
PRICING LISTED IS NOT MOUNTED OR WIRED.
• Auto Restart Control, 1 Phase, Non-Reversing
EA-012 (115 Volt) ...........................
EA-017 (230 Volt) ...........................
Includes: Photo Eye (033.2122), Dual
Time Delay Module (033.2172),
Combination Magnetic Starter with extra
Contactor (033.160), Pushbutton Station
(033.195), and (230 V. Only) a Control
Circuit Transformer (As Required).
Note: Above Price does NOT include
Photo Eye Mounting Bracket.
$3,253.63
$3,391.27
Add on $192.70 for the above Push Buttons
  to be Mounted.
Add on $995.10 for the above Starters and
  Push Button Stations to be Mounted and Wired.
  Supply 20'0" of cable for push button only.
• Mounting Brackets for photo eye
#033.2122
B-05165 ..............................................
$118.10

CONVEYOR WEIGHT CHART
OAW-4 in., 5 in., 6 in., 7-1/2 in., 10 in. and 12 in. Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 19" 21" 23" 25" 27" 31" 33" 37" 39" 43" 47" 51" 55" 61" 67"
Overall Frame Width 22-1/4" 24-1/4" 26-1/4" 28-1/4 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
*4" Centers 10' Length-
OA Per Foot
No. 40
Chain
808 845 882 919 956 1030 1067 1141 1178 1252 1326 1400 1474 1585 1696
73 77 81 85 89 97 101 109 113 121 129 137 145 157 169
5" Centers 10' Length-
OA Per Foot
No. 50
Chain
707 742 777 812 847 917 952 1022 1057 1127 1197 1267 1337 1442 1547
65 69 73 77 81 89 93 101 105 113 121 129 137 149 161
6" Centers 10' Length-
OA Per Foot
No. 60
Chain
639 673 707 741 775 843 877 945 979 1047 1115 1183 1251 1353 1455
59 62 65 68 71 77 80 86 89 95 101 107 113 122 131
7-1/2" Centers 10' Length-
OA Per Foot
No. 60
Chain
572 605 638 671 704 770 803 869 902 968 1034 1100 1166 1265 1364
55 59 61 64 67 73 76 82 85 91 97 103 109 118 127
OAW-3 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22-1/4" 24-1/4" 26-1/4" 28-1/4" 30-1/4" 34-1/4" 36-1/4" 40-1/4" 42-1/4" 46-1/4" 50-1/4" 54-1/4" 58-1/4" 64-1/4" 70-1/4"
Overall Frame Width 25-1/2" 27-1/2" 29-1/2" 31-1/2" 33-1/2" 37-1/2" 39-1/2" 43-1/2" 45-1/2" 49-1/2" 53-1/2" 57-1/2" 61-1/2" 67-1/2" 73-1/2"
3" Centers 10' Length-
OA Per Foot
No. 60 Chain 976 1016 1056 1096 1136 1216 1256 1336 1376 1456 1536 1616 1696 1816 1936
87 90 93 96 99 103 108 114 117 123 129 135 141 150 159
OAW-3 3/4 in Roller Centers
Conveying Surface 15-3/4" 17-3/4" 19-3/4" 21-3/4" 23-3/4" 27-3/4" 29-3/4" 33-3/4" 35-3/4" 39-3/4" 43-3/4" 47-3/4" 51-3/4" 57-3/4" 63-3/4"
Between Rail Width 22" 24" 26" 28" 30" 34" 36" 40" 42" 46" 50" 54" 58" 64" 70"
Overall Frame Width 25-1/4" 27-1/4" 29-1/4" 31-1/4" 33-1/4" 37-1/4" 39-1/4" 43-1/4" 45-1/4" 49-1/4" 53-1/4" 57-1/4" 61-1/4" 67-1/4" 73-1/4"
3 3/4" Centers 10' Length-
OA Per Foot
No. 60 Chain 839 879 919 959 999 1079 1119 1199 1239 1319 1399 1479 1559 1629 1799
78 81 84 87 90 96 99 105 108 114 120 126 132 141 150
*#40 chain reduces total conveyor capacity. Consult us.
All weights are conveyor weights only. Accessories, crating, etc., are not included.
Note:
Add 1-3/8” to OAL for Chain Guard End Caps on 4” centers only.
Note:
Add 3” to OAL for Chain Guard End Caps on 3” roller centers only.
Chain Driven Live Roller Conveyor, Roll-to-Roll, Chain Driven Live Roller Conveyors, Conveyor, Live Roller
Conveyors, Powered Live Roller, Conveyors, and Roller Conveyors from your source for material handling
equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart