Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

MODEL TW

HORIZONTAL WIRE MESH
BELT CONVEYOR

horizontal wire mesh belt conveyor
The Model TW with wire belt can carry
hot or cold parts from ovens or freezers.
Can be used in drying operations.
3 Belt Widths
Wire Mesh Belt
Adjustable MS-Type Floor Supports
   Available

belt conveyor
LOAD CAPACITY CHART @ 65 FPM
HP BED WIDTHS - 16" to 28"
TOTAL LOAD (Lbs.)
UP TO 50' UP TO 100'
1/2 850 350
1 1950 1500

STANDARD SPECIFICATIONS
BELT–1/2 in. x 1 in. flat galvanized wire mesh belt.
    Maximum product temperature 350°F.
RETURN IDLER–Adjustable 1.9 in. dia. pre-
    lubricated ball bearings.
BED–Roller bed with 1.9 in. dia. roller x 16 ga.
    galvanized tube spaced every 6 in. Mounted in
    6-5/8 in. x 12 ga. powder painted formed steel
    channel frame bolted together with splice plates.
TAKE-UP–Take-ups at tail pulley. Provides 4 in.
    of belt take-up.
BEARINGS–Sealed, pre-lubricated, self-aligning
    ball bearings on drive and tail shafts. Pre-lubricated
    ball bearings in tread rollers.
CROSS BRACING–Rods with turnbuckles are
    fastened to underside of bed to provide alignment of
    bed rollers to insure correct belt tracking. Required
    on every other section 30 ft. bed lengths and over.
SPEED REDUCTION–Sealed worm gear C-Face
    speed reducer. No. 50 roller chain to drive sprocket.
MOTOR–1/2 HP–208/230/460/575V–3 Ph.
    60 Hz. Totally Enclosed C-Face.
END DRIVE–Located on discharge end of conveyor,
    chain guard on left hand side.
CAPACITY–Maximum load per linear foot of
    conveyor 75 lbs. NOT TO EXCEED capacity in
    chart.
DRIVE SPROCKETS–6 in. pitch dia. multiple cast
    iron sprockets with 1-3/16 in. dia. shaft 6 in. centers.
TAIL PULLEY–4 in. dia. with 1 in. dia. shaft at
    bearings. Sprocket at each end.
FLOOR SUPPORTS–Now supplied as optional
    equipment.
SNUB IDLER–Adjustable 2-1/8 in. dia. pre-
    lubricated ball bearings.
BELT SPEED - Constant 65 FPM.

OPTIONAL EQUIPMENT
FLOOR SUPPORTS–MS Type floor supports are
    available with a wide range of adjustment. Specify top
    of belt or roller elevation. One support required at
    every bed joint and ends of conveyor. Holes in feet
    for lagging to floor. Knee braces recommended
    above MS-6 support.
V-BELT DRIVE–V-Belt supplied between motor
    and reducer.
O-RING DRIVE CHAIN–With sealed in lubricant
    (Recommended for applications that do not permit
    regular lubrication).
CEILING HANGERS–5/8 in. dia. x 8 ft. long
    unplated rods fully threaded. Other lengths and
    galvanized rods available.
BED–Slider bar in place of roller bed.
BELT–Other widths than standard, galvanized low
    carbon steel, bright high carbon steel or stainless steel.
    1 in. or 1/2 in. x 1/2 in. mesh available. Maximum
    product temperature 750°F with high carbon steel
    belt.
MOTORS–Energy efficient, single phase, other
    characteristics. 1 HP maximum.
ELECTRICAL CONTROLS–Non-reversing
    magnetic starters and push-button stations. AC
    variable frequency drive.
BELT SPEED–Other constant and variable speeds.
    V-belt drive supplied on speeds under 15 FPM and
    with variable speeds. NOTE: Capacity affected
    with speed change.

PRICES FOR COMPLETE CONVEYOR INCLUDE:
1/2" x 1" Wire Mesh Galvanized Belt Totally Enclosed Chain Guard

1.9" Dia. Roller (Rollers on 6" Centers) in a 6-5/8"
   x 12 Ga. Steel Channel Frame

65 FPM Belt Speed
Less Electrical Controls
6" Pitch Dia. Drive Sprockets
Less Supports
"C" Face Speed Reducer - Sealed Worm Gear
1/2 HP - "C" Face Totally Enclosed Motor
    (Specify Exact Voltage)

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


IMPORTANT NOTES...
OTHER LENGTHS OTHER WIDTHS
  Other lengths not listed in price chart are available. For
"IN-BETWEEN SIZES", use next larger. Overall
Length "A" price. For lengths longer or shorter than
those shown in chart, please contact us.
  For "IN-BETWEEN WIDTHS", use next width plus
10%. For widths up to 52" OAW, interpolate plus
10%. For widths over 52" OAW, contact us.
NON-STANDARD WIDTHS
FLOOR SUPPORTS
  Contact us for lead time.
  Floor Supports are not included in base price. There
are two (2) stationary floor supports required for
the first bed section and one (1) support per bed
section thereafter.
INTERMEDIATE BEDS
  Use per foot price of width x required length,
supports not included.
SIZE TO
ORDER
Overall
Length "A"
Bed
Length
"L"
Wire Mesh Belt Width
6" 8" 12" 18" 20" 24"
Roller Bed Width
    10" 12" 16" 22" 24" 28"
6'-1" 5'
11'-1" 10'
16'-1" 15'
21'-1" 20'
26'-1" 25'
31'-1" 30'
36'-1" 35'
41'-1" 40'
46'-1" 45'
51'-1" 50'
56'-1" 55'
61'-1" 60'
66'-1" 65'
71'-1" 70'
76'-1" 75'
81'-1" 80'
86'-1" 85'
91'-1" 90'
96'-1" 95'
101'-1" 100'
Per Foot Price

PRICES FOR OPTIONAL EQUIPMENT
OPTIONAL DRIVES FLOOR SUPPORTS
Drive BED WIDTHS
Type 16" to 22" 28"
End Drive (V-Belt)
Side Mounted
Overhead
Not included in base price. Use chart below for
required elevation.
'MS" SUPPORT
Model No. Adjustment to Top of Belt Price Each
MSL-1* 9-3/8" to 10-3/8"
MSL-2* 10-3/8" to 12-1/8"
MSL-3* 12-1/8" to 14-3/4"
MS-1* 14-3/8" to 16-1/8"
MS-1.2* 15-3/8" to 17-1/8"
MS-1.4* 16-3/8" to 18-1/8"
MS-2 17-3/8" to 20-3/8"
MS-3 20" to 23"
MS-4 23" to 29"
MS-5 27" to 33"
MS-6 31" to 43"
MS-7 41" to 53"
MS-8 53" to 65"
MS-9 65" to 77"
MS-10 77" to 89"
MS-11 87" to 99"
MS-12 99" to 111"
#50 O-Ring Drive Chain ............Add ...........
CONSTANT AND VARIABLE SPEEDS
Constant C-Face - Within 15-70 FPM ......No Charge
Constant V-Belt - Minimum of 4 FPM ....................
................................... Use V-Belt Drive Add-On
DRIP PANS
Add-On per foot of conveyor .....................
UNDERSIDE BED COVERS
Add-On per foot of conveyor .....................
GUARD RAILS
Adjustable Universal Channel Guard Rail
Both Sides ...................per foot .................
One Side .....................per foot .................
NOTE: PC Type guard rail only. Available in 5’ and 10’
lengths from factory. Contact us for other lengths.
NOTE: MS-7 to MS-12: Knee Braces included in price.
HEIGHT
(Both Sides-Per Foot)
TYPE
Solid Side PC Type
2"
N/A
3-1/2"
N/A
4"
N/A
6"
9"
12"
Knee Braces ..............Add per pair ............
*Less than 9-1/8" top of roller elevation-
Side Mounted Drive Required.
ELECTRICAL CONTROLS
(See Below)
GALVANIZING
Contact us.
NOTE: Solid Side Guards mount vertically on
outside of conveyor bed, PC Type Guards mount
on top of bed.
DRIVE COMPONENT DEDUCTS OPTIONAL ROLLER CENTERS
Less Motor Drive, Motor Mount and Guards, but
with Shaft Extension and Sprocket.....................

3" Centers
10"-12" ..........per foot of conveyor............
16"..................per foot of conveyor............
22"..................per foot of conveyor............
28"..................per foot of conveyor............


$23.40
$23.40
$28.40
$32.70

..............................Deduct ......................
$694.20
Less Motor Only (1/2 HP-208/230/460/
575V- 3 Ph.-60Hz.).........Deduct ..............
$258.30
*Less Reducer ................Deduct ...............
$318.70
SLIDER BAR
*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less chain
guard and sprockets when C-Face drive is supplied.
Slider Bar Construction (Herringbone Type Design)
in place of rollers ..................................................
...................Per Foot of Conveyor ............. $32.40
MOTORS
Extra Motor Price for OTHER THAN: 1/2 HP–208/230/460/575 V–3 Ph.–60 Hz.–Totally Enclosed. Speed affects
horsepower requirements.
H.P. REQ.
TOTALLY ENCLOSED 
PREMIUM ENERGY EFFICIENT
BRAKE MOTORS 
200/208/230/
460/575V
3 Ph.-60 Hz.
115/230V
1 Ph.-60 Hz.
230/460V
3 Ph.-60 Hz.
575V
3 Ph.-60 Hz.
Holding Brake
208/230/
460/575V
3 Ph.-60Hz.
Holding Brake
115/230V
1 Ph.-60Hz.
1/2
N/A
N/A
1
N/A
2
N/A
* Note: "High Cycle Brakemotors" are used for indexing and are rated for 30 cycles per minute. Add-On Prices
   Include 5AC Reducer, Heavy Duty Motor Base Plate, and #60 Chain and Sprockets with Taper Bushed Hubs.
** Note: "High Cycle Brakemotor" Add-On Prices Include 5AC Reducer, Heavy Duty Motor Base Plate and
     Timing Belt Drive.
Note: SSB and D Series are Holding Brakes and are NOT rated for cycling.

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CEILING HANGERS
Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated
fully threaded rods ......................................................................
ceiling hangers for conveyors $147.90
Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized
fully threaded rods .......................................................................
$176.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated fully
threaded rods................................................................................
$218.40
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized fully threaded rods.................................................................................
$359.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated fully threaded rods.................................................................................
$362.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized fully threaded rods..................................................................................
$419.40
Ceiling Hanger Brackets, Less Rods Only .................................... $93.10
Extra Length Rods:
(2) 8’-0” long x 5/8” dia. unplated fully threaded rods .................. $54.20
(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods ............... $83.40
(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ................ $125.20
(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods ............. $266.30
(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ................ $269.60
(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods ............. $326.50
Hex Coupling Nuts for Rods ......................................................... $4.90
Above noted delivery times determined by delivery time of model ordered.
POLY-TIER SUPPORTS
poly tier supports for conveyors
PRICES FOR COMPLETE
SUPPORT INCLUDE:
IMPORTANT NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.
• Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
   conveyor)
• "U" Brackets
• Single Width Conveyor Only
CAPACITY DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs
(2) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"
(3) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


ELECTRICAL CONTROLS AND DRIVE SECTION
MANUAL START SWITCH or
SAFETY DISCONNECT
limit switch LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER
manual start switch
#032.1014......................................... $213.01 #033.2032 & #033.2072..................$555.67
Nema 4
"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)
LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER
limit switch double pole

#033.2033& #033.2072...................$332.11
Nema 4
REVERSING DRUM SWITCH
#032.103.......................................... $854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase
PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range


foot swtich with guard FOOT SWITCH WITH GUARD
#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range
#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.


PHOTO EYE, ON-OFF TYPE
power cord and plug #EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC
POWER CORD AND PLUG (20')
POWER CORD WITH PLUG ONLY 20' LONG
Model No.
Voltage
HP Rating
Prices
EA-039-1A
115/1
1/2-3/4
EA-039-2A
115/1
1
EA-039-3A
115/1
1 1/2
EA-039-4A
230/1
1/2-1
EA-039-5A
230/1
1 1/2-2
EA-039-6A
208-230/3
1/2-2
EA-039-7A
460/3
1/2-2
POWER CORD WITH PLUG 20' LONG WITH MANUAL START SWITCH AND MOUNTING BRACKET
Model No.
Voltage
HP Rating
Prices
EA-039-1B
115/1
1/2-3/4
EA-039-2B
115/1
1
EA-039-3B
115/1
1 1/2
EA-039-4B
230/1
1/2-1
EA-039-5B
230/1
1 1/2-2
EA-039-6B
208-230/3
1/2-2
EA-039-7B
460/3
1/2-2
MOUNTING BRACKETS FOR PHOTO
EYE #033.2122
B-05165...........................................$118.10

AIR PRESSURE SWITCH
#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH
#032.285 with 032.2851 Turnbuckle
...........................................................
$696.08
Nema 4
"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE
#032.281...one side.................$7.44 per / ft.
                  both sides..............$15.87per / ft.
EMERGENCY PUSH BUTTON
#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE
#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48
NOTE: PRICING LISTED NOT MOUNTED
             OR WIRED
"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC
#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CONTROLLER PRICES
AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size 115 Volt 208/230 Volt
1/2 VSC-12-10 VSC-12-12
Price $1,491.84 $1,189.37
1 VSC-12-11 VSC-12-13
Price $1,724.27
2 N/A
VSC-12-14
Price ~
THREE PHASE CONTROLLER INPUT
Motor Size 208/230 Volt 460 Volt 575 Volt
1/2
VSC-01-15
VSC-01-18
VSC-12-29
Price
1
VSC-01-16
VSC-01-19
VSC-12-29
Price
2
VSC-01-17
VSC01--20
VSC-12-30
Price
REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS
HP Part No. Price
1/2 032.351 230/460
1 032.353 230/460
2 032.355 230/460
1/2 032.3512 575
1 032.3532 575
2 032.3552 575
IMPORTANT NOTES...
All above motors are 230 / 460 / 575 Volt, 3 Phase.
All above V/S Drive Kits include NEMA 1 / IP30
  Junction Box, Controller and Motor.
Good for cycle rates of up to 15 cycles per minute, at
  1/2 second ramp time, with a maximum speed of 250
  FPM.
Drawing No. DG-001146.
OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)
$675.20 When AC Variable Speed Controller is used with a
   Brake Motor, A Brake Relay Kit (EA-068A) is
   required. Add an additional $542.68 for this option.)
Brake Relay Kit (EA-068A).............................. $542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE
Part No. Description Price
EA-VSC-01-CB 2 HP Electronic Clutch-Brake Kit $5,058.00
OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)
$675.20
KIT INCLUDES
Part No. Description
VSC-01-20 AC Variable Speed Controller, 460 Volt, 3 Phase
032.345 2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
IMPORTANT NOTES
Good for cycle rates of up to 60 cycles per minute.
1/10 second Accel and Decel time, with 350 FPM
   Maximum Speed.
230 or 460 Volt Only, Other Voltages, Contact us.
Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
Price Includes 5AC Reducer and #60 Chain and
  Sprockets
Part No. Description
VSC-01-17 AC Variable Speed Controller, 230 Volt, 3 Phase
032.345 2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


starter
THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use
.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
MOTOR
DUTY
NON-REVERSING
REVERSING
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
1/2
STANDARD EASY
CLEAN ENERG. EFF.
$1516.60
$2,023.30
 
 
 
 
 
 
 
 
1
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
1-1/2
GEARMOTORS
 
 
 
 
 
 
 
 
2
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
NON-REVERSING
REVERSING
NON-REVERSING
REVERSING
 
115 VOLT
PRICE
115 VOLT
PRICE
230 VOLT
PRICE
230 VOLT
PRICE
1/2
$1,182.40
$2,023.30
$1,435.60
$2,023.30
1
1-1/2
2
• Manual Start-Stop Switch Kit • Start-Stop Push Button Kit, Remote Mounted
EA-000001 ...................................... $242.09 EA-000002....................................... $242.09
Includes: 032.1014 Manual Start Switch, Nema 1,
B-21467 Mounting Bracket with Mounting Hardware
Includes: 033.1955 Push Button Station, One
Direction, Nema1, B-21467 Mounting Bracket
with Mounting Hardware
Forward-Reverse-Stop Push Button Kit,
  Remote Mounted
• Up-Down-Stop Push Button Kit, Remote
   Mounted
EA-000003....................................... $440.67
Includes: 033.1965 Push Button Station, Reversing,
Nema1, B-21467 Mounting Bracket with Mounting
Hardware
EA-000004....................................... $440.67
Includes: 033.1975 Up Down Stop Push Button
Station, Reversing, Nema 1, B-21467 Mounting
Bracket with Mounting Hardware

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station • “Start-Stop”Push-button Station
033.1955
$211.23 033.195................................................. $142.50
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Fwd-Rev-Stop” Push-button Station • “Fwd-Rev-Stop”Push Button Station
033.1965 $397.05 033.196.................................................. $490.95
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Up-Down-Stop” Push-button Station
OPTIONAL STARTER CONTROLS
033.1975 $397.05
• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1
EA-011 ............................................
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
$3,210.68
IMPORTANT NOTES
Control Circuit Transformer Included for 115 Volt
  Control Voltage.
Above starters are in Nema 3, 4 and 12 Enclosures.
The starters included Safety Disconnect, Overload
  Relay, and Aux. Contacts as required.
IF AN ORDER IS SUPPLIED LESS MOTOR,
  AND IS SUPPLYING ANY ELECTRICAL
  CONTROLS, THEN MOTOR HP, VOLTAGE,
  PHASE, AND FULL LOAD CURRENT MUST BE
  STATED ON THE ORDER.
PRICING LISTED IS NOT MOUNTED OR WIRED.
• Auto Restart Control, 1 Phase, Non-Reversing
EA-012 (115 Volt) ...........................
EA-017 (230 Volt) ...........................
Includes: Photo Eye (033.2122), Dual
Time Delay Module (033.2172),
Combination Magnetic Starter with extra
Contactor (033.160), Pushbutton Station
(033.195), and (230 V. Only) a Control
Circuit Transformer (As Required).
Note: Above Price does NOT include
Photo Eye Mounting Bracket.
$3,253.63
$3,391.27
Add on $192.70 for the above Push Buttons
  to be Mounted.
Add on $995.10 for the above Starters and
  Push Button Stations to be Mounted and Wired.
  Supply 20'0" of cable for push button only.
• Mounting Brackets for photo eye
#033.2122
B-05165 ..............................................
$118.10

CONVEYOR WEIGHT TABLE
SIZE TO
ORDER
Overall
Length "A"
Bed
Length
"L"
Belt Width 12" 18" 24"
Bed Width 16" 22" 28"
6'-1" 5'





WEIGHTS
(Lbs.)
299 322 365
11'-1" 10' 368 415 465
16'-1" 15' 461 525 593
21'-1" 20' 530 608 693
26'-1" 25' 623 718 821
31'-1" 30' 692 801 921
41'-1" 40' 854 994 1149
51'-1" 50' 1023 1197 1391
61'-1" 60' 1185 1390 1609
71'-1" 70' 1355 1594 1862
81'-1" 80' 1517 1787 2090
91'-1" 90' 1697 1979 2319
101'-1" 100' 1841 2172 2547
All weights are conveyor weights only.
Accessories, crating, etc., are not included.
Belt Conveyors, Conveyor, Conveyor Belt, Wire Mesh Belt Conveyor, Wire Belt, Incline Conveyor, Parts Conveyor, Conveyors, and
Mesh Belt from your source for material handling equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart