Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

MODEL PSB PLASTIC BELT CONVEYOR

The Model PSB with modular plastic
belting uses a positive drive system to
eliminate belt slippage and mistracking.
• 16 Belt Widths
• Polypropylene 2” Pitch Plastic Belt
• Adjustable MS-Type Floor Supports Available


LOAD CAPACITY CHART @65 FPM
 HP 
 16” TO 28” OVERALL WIDTH 
 TOTAL LOAD (LBS.) 
 UP TO 50’ 
 1/2
 750 
 1 
 1750 
 2 
 3750 

Standard Specifications
END DRIVE–Located on discharge end of conveyor.
Chain guard located on left hand side.
SNUB ROLLERS–Located at drive and tail ends.
RETURN BARS–UHMW on aluminum.
BELT–Polypropylene 2 in. pitch Flush Grid, nominal
1 in. less than BR.
BEARINGS–Sealed, pre-lubricated, self-aligning ball
bearings on drive and tail shafts.
BED–UHMW on aluminum slider bars, mounted to
frame spacers. Mounted in 7 1/2 in. x 12 ga. powder
painted, formed steel channel frame bolted together
with butt couplings.
SPEED REDUCTION–Sealed worm gear C-Face
speed reducer. No. 50 roller chain to drive sprocket.
MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz.
Totally Enclosed C-Face.
CROSS BRACING–Rods with turnbuckles are
fastened to underside of bed to provide alignment of
bed sections to insure correct belt tracking. Supplied
on every other section 30 ft. bed lengths and
over.
BELT SPEED–Constant 65 FPM.
CAPACITY–Maximum load per linear foot of conveyor
200 lbs. NOT TO EXCEED capacity in chart.
DRIVE AND TAIL SPROCKETS–10 tooth 6.4 in.
pitch dia. molded plastic sprockets on 1 1/2 in. sq.
shaft, 1 3/16 in. dia. shaft at bearings.
Optional Equipment
FLOOR SUPPORTS–MS Type floor supports are
available with a wide range of adjustment. Specify
top of belt or roller elevation. One support required
at every bed joint and ends of conveyor. Holes in feet
for lagging to floor. Knee braces recommended above
MS-6 support.
O-RING DRIVE CHAIN–With sealed in lubricant
(Recommended for applications that do not permit
regular lubrication).
CEILING HANGARS–5/8 in. dia. x 8 ft. long unplated
rods fully threaded. Other lengths and galvanized rods
available.
BED–Stainless steel in lieu of powder painted HRS
(Excluding Aluminum Support Bars).
NOSEOVER AND NOSEUNDER–Can be in-
corporated to provide continuous belt travel from
horizontal to incline or decline.
BELT–Other belts available, contact us.
BELT SPEED–Other constant and variable speeds.
V-belt drive supplied on speeds under 15 FPM and
with variable speeds. Note: Capacity affected with
speed change.
MOTORS–Energy efficient, single phase, brakemotor,
other haracteristics. 2 HP maximum.
ELECTRICAL CONTROLS–One direction magnetic
starters and push-button stations. AC Variable Frequency
Drive.

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


PRICES FOR COMPLETE CONVEYOR INCLUDE:
• Polypropylene 2 in. pitch flush grid
• 7 1/2 in. x 12 ga. powder painted, formed steel
   channel frame with UHMW on aluminum slider bars
• 6.4” Pitch Dia. x 20 tooth Drive & Tail Sprockets
• “C” Face Speed Reducer–Sealed Worm Gear
• 1/2 HP–“C” Face Totally Enclosed Motor (Specify
   Exact Voltage)
• Totally Enclosed Chain Guard
• 65 FPM Belt Speed
• Less Electrical Controls
• Less Supports
PRICING FOR PSB Plastic Belt Conveyor
SIZE TO
ORDER
Overall
Length "A"
Plastic Belt Widths
8"
10"
12"
14"
16"
18"
20"
22"
Overall Bed Widths
12"
14"
16"
18"
20"
22"
24"
26"
10'-0"
Per Foot
SIZE TO
ORDER
Overall
Length "A"
Plastic Belt Widths
24"
26"
28"
30"
32"
34"
36"
38"
Overall Bed Widths
28"
30"
32"
34"
36"
38"
40"
42"
10'-0"
Per Foot
IMPORTANT NOTES
• OTHER LENGTHS
  For lengths longer or shorter than those shown in chart, use per foot price.
• OTHER WIDTHS 
For widths less than 12” OAW , use 12” OAW price plus 10%. For widths over 42” OAW, and up to
60” OAW, interpolate plus 25%.
• FLOOR SUPPORTS
There are two (2) stationary floor supports required for the first bed section and one (1) support per bed
section thereafter.
• NON-STANDARD WIDTHS
Contact us for lead time.

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


MOTORS
Extra Motor Price for OTHER THAN: 1/2 HP–208/230/460/575 V–3 Ph.–60 Hz.–Totally Enclosed.
Speed affects horsepower requirements.
H.P.
REQ.
TOTALLY ENCLOSED 
ENERGY EFFICIENT
BRAKEMOTORS 
200/208/230/
460/575V
3 Ph.-60 Hz.
115/230V
1 Ph.-60 Hz.
230/460V 3 Ph.-60 Hz. 575V 3 Ph.-60 Hz. Holding Brake
208/230/
460/575V
3 Ph.-60Hz.
Cycling Brake 208/230/
460/575V*
3 Ph.-60Hz.
Cycling Brake 208/230/
460/575V
*
3 Ph.-60Hz.
Holding Brake
115/230V
1 Ph.-60Hz.
1/2
 N/A  
 N/A  
 N/A  
 N/A  
1
N/A
2
N/A
*575V - Prices coded in light blue call for lead time.
* NOTE: "High Cycle Brakemotors" are used for indexing and are rated for 30 cycles per minute. Add-On Prices Include 5AC Reducer,
Heavy Duty Motor Base Plate, and #60 Chain and Sprockets with Taper Bushed Hubs.
** NOTE: "High Cycle Brakemotor" Add-On Prices Include 5AC Reducer, Heavy Duty Motor Base Plate and Timing Belt Drive.
NOTE: SSB and D Series are Holding Brakes and are NOT rated for cycling.
FLOOR SUPPORTS OPTIONAL DRIVES
Not Included in Base Price. Use Chart Below for
Required Elevation.
Optional Drives
Drive Type
12"-20"
22"-30"
32"-42"
End Drive
(V-Belt)
Side Mounted
(C-Face)
Side Mounted
(V-Belt)
Center
(C-Face)
Center
(V-Belt)
Overhead
(C-Face)
Overhead
(V-Belt)
MS SUPPORT
Model No.
Adjustment to
Top of Belt
Price each
*MSL-1
9 3/4" to 10 3/4"
*MSL-2
10 3/4" to 12 1/2"
*MSL-3
12 1/2" to 15 1/8"
*MS-1
14 3/4" to 16 1/2"
*MS-1.2
15 3/4" to 17 1/2"
*MS-1.4
16 3/4" to 18 1/2"
*MS-2
17 3/4" to 20 3/4"
MS-3
20 3/8" to 23 3/8"
MS-4
23 3/8" to 29 3/8"
MS-5
27 3/8" to 33 3/8"
MS-6
31 3/8" to 43 3/8"
MS-7
41 3/8" to 53 3/8"
MS-8
53 3/8" to 65 3/8"
MS-9
65 3/8" to 77 3/8"
MS-10
77 3/8" to 89 3/8"
MS-11
87 3/8" to 99 3/8"
MS-12
99 3/8" to 111 3/8"
#50 O-Ring Drive Chain............Add ........ $284.40
GUARD RAILS*
Adjustable Universal Channel Guard Rail
Both Sides .................. per foot ................. $15.10
One Sides .................. per foot .................. $7.80
Angle Type
Types “A” or “B” available (specify).
Prices are for both sides.
Type “A”
1 1/2” x 1 1/2” x 12 Ga.......... per foot............... $7.80
*Less than 19 15/16" top of belt elevation -
Type “B” (See NOTE)
1 1/2” x 1 1/2” x 12 Ga.......... per foot............... $10.90
Side mounted Drive Required
NOTE: MS-7 to MS-12: Knee Braces included in price
Extra Knee Braces .......... per pair....................................... $30.00
Fixed Channel Type
(Prices are for both sides.)
Single Center Leg (MSC-6 and below) each.................... $60.40
Single Center Leg (MSC-7 and above) each.................... $75.10
3 1/2” x 1 1/2” x 12 Ga........... per foot............. $22.50
* NOTE: If product comes in contact with guard rails, product
flow will be affected.
CEILING HANGERS CONSTANT AND VARIABLE SPEEDS
Ceiling Hanger Brackets with (2) 5/8" dia. x
8'-0" long unplated fully threaded rods.........
Constant C-Face–Within 15-70 FPM....No Charge

$147.90

Constant V-Belt–Minimum of 4 FPM........
.................................Use V-Belt Drive Add-On
Ceiling Hanger Brackets with (2) 5/8" dia. x
8'-0" long galvanized fully threaded rods.......
$176.60
DRIVE COMPONENT DEDUCTS
Ceiling Hanger Brackets with (2) 5/8” dia.
x 10’-0” long unplated fully threaded rods.....
Less Motor Drive, Motor Mount and Guards, but
with Shaft Extension and Sprocket .......
Deduct ................................................. $694.20
$218.40
Ceiling Hanger Brackets with (2) 5/8” dia.
x 10’-0” long galvanized fully threaded rods....
$359.60
Less Motor Only (1/2 HP-208/230/460/575 V-
3 Ph.-60 Hz.) ..... Deduct....................... $258.30
Ceiling Hanger Brackets with (2) 5/8” dia.
x 12’-0” long unplated fully threaded rods.....

$362.60

Less Reducer*...............Deduct............. $307.40
Ceiling Hanger Brackets with (2) 5/8” dia.
x 12’-0” long galvanized fully threaded rods....
*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less chain
guard and sprockets when C-Face drive is supplied.
$419.40
Ceiling Hanger Brackets, Less Rods Only.... $93.10
Extra Length Rods:
CENTER BEARING SUPPORT (END DRIVE)
(2) 8’-0” long x 5/8” dia. unplated fully
threaded rods ............................................
(Drive and Tail) ..............Add On........... $676.10
$54.20
(2) 8’-0” long x 5/8” dia. galvanized fully
threaded rods .............................................
GALVANIZING - Contact us.
$83.40
POLY-TIER SUPPORTS
(2) 10’-0” long x 5/8” dia. unplated fully
threaded rods ..............................................
$125.20 poly tier supports for conveyors PRICES FOR COMPLETE
CONVEYOR INCLUDE:

• Painted Steel Support Legs
• Adjustable Crosspipe Assembly
• Knee Braces (1 set per level of
  conveyor)
• “U” Brackets
• Single Width Conveyor Only
(2) 10’-0” long x 5/8” dia. galvanized fully
threaded rods ..............................................
$266.30
(2) 12’-0” long x 5/8” dia. unplated fully
threaded rods ..............................................
$269.60
(2) 12’-0” long x 5/8” dia. galvanized fully
threaded rods ..............................................
$326.50
IMPORTANT NOTES. . .
• Check for Clearance.
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.
Hex Coupling Nuts for Rods ................... $4.90
CAPACITY DATA:
1500 lbs. ...........per cross pipe
4500 lbs. ...........per set of legs
(2) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"
(3) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


ELECTRICAL CONTROLS AND DRIVE SECTION
MANUAL START SWITCH or
SAFETY DISCONNECT
limit switch LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER
manual start switch
#032.1014......................................... $213.01 #033.2032 & #033.2072..................$555.67
Nema 4
"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)
LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER
limit switch double pole

#033.2033& #033.2072...................$332.11
Nema 4
REVERSING DRUM SWITCH
#032.103.......................................... $854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase
PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range


foot swtich with guard FOOT SWITCH WITH GUARD
#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range
#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.


PHOTO EYE, ON-OFF TYPE
power cord and plug #EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC
POWER CORD AND PLUG (20')
POWER CORD WITH PLUG ONLY 20' LONG
Model No.
Voltage
HP Rating
Prices
EA-039-1A
115/1
1/2-3/4
EA-039-2A
115/1
1
EA-039-3A
115/1
1 1/2
EA-039-4A
230/1
1/2-1
EA-039-5A
230/1
1 1/2-2
EA-039-6A
208-230/3
1/2-2
EA-039-7A
460/3
1/2-2
POWER CORD WITH PLUG 20' LONG WITH MANUAL START SWITCH AND MOUNTING BRACKET
Model No.
Voltage
HP Rating
Prices
EA-039-1B
115/1
1/2-3/4
EA-039-2B
115/1
1
EA-039-3B
115/1
1 1/2
EA-039-4B
230/1
1/2-1
EA-039-5B
230/1
1 1/2-2
EA-039-6B
208-230/3
1/2-2
EA-039-7B
460/3
1/2-2
MOUNTING BRACKETS FOR PHOTO
EYE #033.2122
B-05165...........................................$118.10

AIR PRESSURE SWITCH
#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH
#032.285 with 032.2851 Turnbuckle
...........................................................
$696.08
Nema 4
"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE
#032.281...one side.................$7.44 per / ft.
                  both sides..............$15.87per / ft.
EMERGENCY PUSH BUTTON
#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE
#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48
NOTE: PRICING LISTED NOT MOUNTED
             OR WIRED
"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC
#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CONTROLLER PRICES
AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size 115 Volt 208/230 Volt
1/2 VSC-12-10 VSC-12-12
Price $1,491.84 $1,189.37
1 VSC-12-11 VSC-12-13
Price $1,724.27
2 N/A
VSC-12-14
Price ~
THREE PHASE CONTROLLER INPUT
Motor Size 208/230 Volt 460 Volt 575 Volt
1/2
VSC-01-15
VSC-01-18
VSC-12-29
Price
1
VSC-01-16
VSC-01-19
VSC-12-29
Price
2
VSC-01-17
VSC01--20
VSC-12-30
Price
REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS
HP Part No. Price
1/2 032.351 230/460
1 032.353 230/460
2 032.355 230/460
1/2 032.3512 575
1 032.3532 575
2 032.3552 575
IMPORTANT NOTES...
All above motors are 230 / 460 / 575 Volt, 3 Phase.
All above V/S Drive Kits include NEMA 1 / IP30
  Junction Box, Controller and Motor.
Good for cycle rates of up to 15 cycles per minute, at
  1/2 second ramp time, with a maximum speed of 250
  FPM.
Drawing No. DG-001146.
OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)
$675.20 When AC Variable Speed Controller is used with a
   Brake Motor, A Brake Relay Kit (EA-068A) is
   required. Add an additional $542.68 for this option.)
Brake Relay Kit (EA-068A).............................. $542.68

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE
Part No. Description Price
EA-VSC-01-CB 2 HP Electronic Clutch-Brake Kit $5,058.00
OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)
$675.20
KIT INCLUDES
Part No. Description
VSC-01-20 AC Variable Speed Controller, 460 Volt, 3 Phase
032.345 2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
IMPORTANT NOTES
Good for cycle rates of up to 60 cycles per minute.
1/10 second Accel and Decel time, with 350 FPM
   Maximum Speed.
230 or 460 Volt Only, Other Voltages, Contact us.
Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
Price Includes 5AC Reducer and #60 Chain and
  Sprockets
Part No. Description
VSC-01-17 AC Variable Speed Controller, 230 Volt, 3 Phase
032.345 2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


starter
THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use
.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
MOTOR
DUTY
NON-REVERSING
REVERSING
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
1/2
STANDARD EASY
CLEAN ENERG. EFF.
$1516.60
$2,023.30
 
 
 
 
 
 
 
 
1
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
1-1/2
GEARMOTORS
 
 
 
 
 
 
 
 
2
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
NON-REVERSING
REVERSING
NON-REVERSING
REVERSING
 
115 VOLT
PRICE
115 VOLT
PRICE
230 VOLT
PRICE
230 VOLT
PRICE
1/2
$1,182.40
$2,023.30
$1,435.60
$2,023.30
1
1-1/2
2
• Manual Start-Stop Switch Kit • Start-Stop Push Button Kit, Remote Mounted
EA-000001 ...................................... $242.09 EA-000002....................................... $242.09
Includes: 032.1014 Manual Start Switch, Nema 1,
B-21467 Mounting Bracket with Mounting Hardware
Includes: 033.1955 Push Button Station, One
Direction, Nema1, B-21467 Mounting Bracket
with Mounting Hardware
Forward-Reverse-Stop Push Button Kit,
  Remote Mounted
• Up-Down-Stop Push Button Kit, Remote
   Mounted
EA-000003....................................... $440.67
Includes: 033.1965 Push Button Station, Reversing,
Nema1, B-21467 Mounting Bracket with Mounting
Hardware
EA-000004....................................... $440.67
Includes: 033.1975 Up Down Stop Push Button
Station, Reversing, Nema 1, B-21467 Mounting
Bracket with Mounting Hardware

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station • “Start-Stop”Push-button Station
033.1955
$211.23 033.195................................................. $142.50
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Fwd-Rev-Stop” Push-button Station • “Fwd-Rev-Stop”Push Button Station
033.1965 $397.05 033.196.................................................. $490.95
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Up-Down-Stop” Push-button Station
OPTIONAL STARTER CONTROLS
033.1975 $397.05
• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1
EA-011 ............................................
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
$3,210.68
IMPORTANT NOTES
Control Circuit Transformer Included for 115 Volt
  Control Voltage.
Above starters are in Nema 3, 4 and 12 Enclosures.
The starters included Safety Disconnect, Overload
  Relay, and Aux. Contacts as required.
IF AN ORDER IS SUPPLIED LESS MOTOR,
  AND IS SUPPLYING ANY ELECTRICAL
  CONTROLS, THEN MOTOR HP, VOLTAGE,
  PHASE, AND FULL LOAD CURRENT MUST BE
  STATED ON THE ORDER.
PRICING LISTED IS NOT MOUNTED OR WIRED.
• Auto Restart Control, 1 Phase, Non-Reversing
EA-012 (115 Volt) ...........................
EA-017 (230 Volt) ...........................
Includes: Photo Eye (033.2122), Dual
Time Delay Module (033.2172),
Combination Magnetic Starter with extra
Contactor (033.160), Pushbutton Station
(033.195), and (230 V. Only) a Control
Circuit Transformer (As Required).
Note: Above Price does NOT include
Photo Eye Mounting Bracket.
$3,253.63
$3,391.27
Add on $192.70 for the above Push Buttons
  to be Mounted.
Add on $995.10 for the above Starters and
  Push Button Stations to be Mounted and Wired.
  Supply 20'0" of cable for push button only.
• Mounting Brackets for photo eye
#033.2122
B-05165 ..............................................
$118.10

CONVEYOR WEIGHT TABLE
MODEL PSB PLASTIC BELT CONVEYOR
 SIZE TO
ORDER
overall
Length
 
 Belt Width 
 8" 
 10" 
 12" 
 14" 
 16" 
 18" 
 20" 
 22" 
 24" 
 26" 
 28" 
 30" 
 32" 
 34" 
 36" 
 38" 
 Between Rail
Width
 
 9" 
 11" 
 13" 
 15" 
 17" 
 19" 
 21" 
 23" 
 25" 
 27" 
 29" 
 31" 
 33" 
 35" 
 37" 
 39" 
 Overall Frame
Width
 
 12" 
 14" 
 16" 
 18" 
 20" 
 22" 
 24" 
 26" 
 28" 
 30" 
 32" 
 34" 
 36" 
 38" 
 40" 
 42" 
 10'
 Weights 
 328 
 248 
 368 
 388 
 408 
 428 
 448 
 468 
 488 
 508 
 528 
 548 
 568 
 588 
 608 
 628 
 WeightsPerFoot 
 18 
 20 
 22 
 24 
 26 
 28 
 30 
 32 
 34 
 36 
 38 
 40 
 42 
 44 
 46 
 48 
Belt Conveyors, Conveyor, Conveyor Belt, Low Profile Conveyor, Conveyors, and Slider Bed from your source for material handling
equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart