Accumulating Conveyor, Conveyor, Plastic Belt Conveyor, Conveyors

Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication


Categories

Back to Product Category

SORRY THIS MODEL HAS BEEN DISCONTINUED. CONTACT US FOR REPLACEMENT PARTS.
MODEL CCEZ
HEAVY DUTY ACCUMULATING CONVEYOR (Zero-Pressure Accumulating Type)

		• EZLogic® Accumulation System (Retro-Reflective) • High Speed • Adjustable MS-Type Floor Supports Available

		The Model CCEZ is a horizontal plastic belt conveyor designed for accumulating 12 & 24 packs of canned beverages where high speeds and large through-puts are required.




	U.S. Patent Number 5,862,907 Other Patents Pending
	U.S. Patent Number 5,862,907 Other Patents Pending


HOW IT WORKS

The conveyor is made up of 24 in. long accumulation zones. The product is conveyed on a low friction plastic belt. The belt is held against the bottom of the product by means of a pair of air actuators. When accumulation begins, EZLogic® Zone Controllers sense product presence, which causes the air actuators to deflate. This allows the plastic belt to lower and sets the product on a pair of UHMW wear bars, where the product slides to a stop. This sequence will continue until the conveyor is loaded. When the discharge zone is signaled to move forward, all zones behind will move forward in sequence.

NOTE: Bed sections available in the following:

	Drive Bed – 8’ Tail Bed – 2’ Intermediate Bed Lengths Must be Multiples of Zone Lengths

Shipping Schedule

Solid Blue or Black prices with Brown shading indicates items available for 3-Day shipment.

Solid Blue or Black prices indicates items available for 2-Week shipment.

Solid Green model numbers or prices indicate items available for 24-Hour Shipment.

Prices coded in light blue call for lead time.

Prices coded in red ship in 4-Weeks.



STANDARD SPECIFICATIONS

BELT–6 in. wide x 1/2 in. thick low friction plastic belt.	AIR REQUIREMENTS–Recommended working pressure 25 P.S.I. Free air consumption at 25 P.S.I.– .0026 cu. ft. per zone actuation.

FRAME–13 in. deep x 1-1/2 in. flange x 12 ga. powder painted steel frame.

	FILTER REGULATOR–Supplied for main air supply line. (3/8 in. NPT port).
DRIVE & TAIL SPROCKETS–12 tooth plastic split sprocket keyed to 1-7/16 in. dia. steel shaft.

		SPEED REDUCTION–Sealed worm gear C-Face speed reducer. no.60 roller chain to drive shaft.

TAKE-UP–Catenary provided at discharge end.

BEARINGS–Sealed, pre-lubricated, regreaseable, self-aligning, ball bearings on drive and tail shaft.

		MOTOR–1 HP–230/460V–3 PH. 60 Hz. Energy Efficient C-Face with AC Variable speed controller.

ACCUMULATION ZONES–24 in. long, air controlled. Note: 51 or more zones will require additional power supply and isolation cable and power supply T cable.

		BELT SPEED–Variable 20 - 200 fpm.

		CAPACITY–See load capacity chart.

	FLOOR SUPPORTS–Now supplied as optional equipment.

IOP–Provides 27VDC, 100 watt power for EZLogic® accumulation system - contains slots for 4 input/output boards. Operates up to 50 zones (25 each side of IOP). Requires 120VAC or 230VAC single phase input.

	EZLogic® ZONE CONTROLLER–Located in each zone (Retroreflective). NEMA 1, 2, IP 62. UL Approved.

6" Belt Width

Length	TOTAL LOAD (LBS) @ 200 FPM (Horizontal)
Length	3/4	1	1 1/2	2	3
20'	360	500	800	1040	1600
30'	330	480	750	1020	1560
40'	300	440	725	1000	1520
50'	N/A	400	700	940	1500
60'	N/A	360	660	925	1470
70'	N/A	N/A	630	910	1440
80'	N/A	N/A	600	880	1400
90'	N/A	N/A	N/A	840	1350
100'	N/A	N/A	N/A	800	1300

NOTE: Standard CCEZ is designed to convey
cartons 4 cans wide.
Use optional 4-1/2 in. belt width
when conveying cartons 3 cans wide.

EZLogic® Accumulation System

EZLogic®, or “Electronic Zero-pressure Logic” Accumulation System, combines the sensing accuracy of photo-
electronics with discrete electronic logic control without the use of a PLC or pneumatic logic components.
The EZLogic® Accumulation System provides many features including:
Zero-pressure accumulation of product
Zone Stop – Always used at the discharge end of the conveyor line to begin accumulation.

Selectable Modes of Operation

Singulation Mode – Product separates while traveling down the conveyor and when it is released from the conveyor
– Zone Off Delay Timer may be used to prevent products from separating while traveling down the conveyor.

Enhanced Slug Mode w/ Jam Protection – Product does not separate when traveling down the conveyor or when
it is released from the conveyor. This allows higher product throughput at any given conveyor speed. Product will not
separate on the conveyor even when accumulation has been activated at the discharge end.

Cascaded Slug Release – Rather than releasing all zones simultaneously, this function introduces a momentary delay
in the release of each zone, from discharge upstream.

Dynamic Zone Allocation – Automatically adjusts the conveyor’s zone length to accommodate the length of the
product being conveyed. Improves conveyor efficiency and system flexibility.

OPTIONAL EQUIPMENT
FLOOR SUPPORTS–MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support.	O-RING DRIVE CHAIN– With sealed in lubricant (Recommended for applications that do not permit regular lubrication).
	4-1/2 in. Belt Width–For conveying cartons 3 cans wide.
	POLY-TIER SUPPORTS–36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.
CONVEYING SPEED–Other constant and variable speeds available. NOTE: Capacity affected with speed change.
	CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated fully threaded rods. Other lengths and galvanized rods available.
SIDE MOUNTED END DRIVE–Motor reducer unit mounted to side of conveyor at discharge end. Minimum elevation to top of belt 14 in.
	EZ-Logic- (See EZLogic Components Section below)

Shipping Schedule

Solid Blue or Black prices with Brown shading indicates items available for 3-Day shipment.

Solid Blue or Black prices indicates items available for 2-Week shipment.

Solid Green model numbers or prices indicate items available for 24-Hour Shipment.

Prices coded in light blue call for lead time.

Prices coded in red ship in 4-Weeks.


PRICES FOR COMPLETE CONVEYOR INCLUDE:

• 6” Wide x 1/2” Thick Low Friction Plastic Belt • 13” x 12 Ga. Painted Channel Frames • 24” Long Air-Controlled Accumulation Zones. EZLogic® Zone Controller NEMA 1, 2, IP 62. UL approved. • “C” Face Speed Reducer–Sealed Worm Gear • 1 HP–”C” Face Energy Efficient (Specify Exact Voltage) • 200 FPM • Filter/Regulator for Main Air Supply Line, and a 45 lbs. Pressure Relief Valve Included		• EZLogic ® Accumulation System • 27 VDC, Power Supply for Modules (Requires 120VAC, 60 Hz Supply) • AC Variable Speed Controller (Not Mounted or Wired) • Less All Other Motor Controls • Stainless Steel Transition Plates-Both Ends • Less Supports

Between Rail Width	13"
Overall Frame Width	16"
Drive & Tail (10' OAL)	$8,877.40
Intermediate Per Foot	$398.65

IMPORTANT NOTES . . .
• OTHER LENGTH
For lengths longer than 10’-0” OAL add per foot price of width
for additional length. Intermediate beds must be ordered in 2’-0”
increments. For special zone or bed lengths, contact us.
• OTHER WIDTHS
For other widths, contact us. All non-standard widths require an
additional 2 weeks.
• FL OOR SUPPORTS
There are two (2) stationary floor supports required for the first
bed section and one (1) support required per bed section thereafter.

NOTE: Combination of drive and tail
section equals 10’-0” OAL.

PRICES FOR OPTIONAL EQUIPMENT

FLOOR SUPPORTS

OPTIONAL BELTS

4-1/2" wide x 1/2" thick low friction plastic belt for
conveying cartons three cans wide . . . .No Add-On
No Deduct.

Not Included in Base Price. Use Chart Below for
Required Elevation.

"MS" SUPPORT
Model No.	Adjustment to Top of Roller	Price each
*MSL-1	12-1/8" to 13-1/8"	$37.96
*MSL-2	13-1/8" to 14-7/8"	$37.96
*MSL-3	14-7/8" to 17-1/2"	$37.96
*MS-1	17-1/8" to 18-7/8"	$37.96
*MS-1.2	18-1/8" to 19-7/8"	$37.96
*MS-1.4	19-1/8" to 20-7/8"	$37.96
*MS-2	20-1/8" to 23-1/8"	$39.15
MS-3	22-3/4" to 25-3/4"	$43.08
MS-4	25-3/4" to 31-3/4"	$49.74
MS-5	29-3/4" to 35-3/4"	$51.77
MS-6	33-3/4" to 45-3/4"	$57.12
MS-7	43-3/4" to 55-3/4"	$84.37
MS-8	55-3/4" to 67-3/4"	$96.39
MS-9	67-3/4" to 79-3/4"	$105.55
MS-10	79-3/4" to 91-3/4"	$120.19
MS-11	89-3/4" to 101-3/4"	$133.04
MS-12	101-3/4" to 113-3/4"	$139.23

OPTIONAL DRIVES

Drive Type	Overall Frame Width
Drive Type	16"
Side Mounted End*	$240.62

17” minimum elevation
V-Belt Drive when required . . . . . . . . .Add . . . .$159.82
#50 O-Ring Drive Chain . . . . . . . . . . .Add . . . . $184.45
#60 O-Ring Drive Chain . . . . . . . . . . .Add . . . . $263.47

MOTORS

Extra Motor Price for OTHER THAN: 1 HP–
208/230/460V–3 Ph.–60 Hz.–Energy Efficient.
Speed affects horsepower requirements

H.P. REQ.	115 V 1 Ph.-60 Hz.	208/230/460 V 1 Ph.-60 Hz.	208/230/460 V 3 Ph.-60 Hz.
H.P. REQ.	1 Ph. AC Controller	1 Ph. AC Controller	3 Ph. AC Controller
1	N/C	N/C	N/C
2	N/A	$790.87	$790.87

TRANSITION

*Less than 24-1/2" top of belt elevation-Side Mounted
Drive Required.
Note: MS-7 to MS-12: Knee Bracess included in price.

7/8” Dia. Transition Roller in lieu of Stainless Steel
Transition Plate . . . . . . . .Add-On Per End . . . . $70.33

Extra Knee Braces.....per pair.................

$18.92

DRIVE COMPONENT DEDUCTS

Single Center Leg (MS-6 and below) each
Single Center Leg (MS-7 and above) each

$39.15

Less Motor Drive, ACController, Motor Mounts and
Guards, but with Shaft Extension . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .Deduct . . . . . . . . .$590.40

$48.67

GALVANIZING

Less Motor Only (1 HP-208/230/460V-3 Ph.-60 Hz.)
and Less AC Controller . . . .Deduct . . . . . . . .$498.10

Less Reducer . . . . . . . . . . .Deduct . . . . . . . . .$185.90
Less V-Belt Guard, Chain Guard, sheaves and sprockets
when V-Belt drive is supplied. Less chain guard
and sprockets when C-Face drive is supplied.

CEILING HANGERS
	Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated fully threaded rods ......................................................................
		$92.82
	Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized fully threaded rods .......................................................................
		$100.08
	Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated fully threaded rods................................................................................
		$102.34
	Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized fully threaded rods.................................................................................
		$131.50
	Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated fully threaded rods.................................................................................

		$134.47
	Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized fully threaded rods..................................................................................
		$154.70
	Ceiling Hanger Brackets, Less Rods Only ....................................	$56.17
	Extra Length Rods:
	(2) 8’-0” long x 5/8” dia. unplated fully threaded rods ..................	$34.27
	(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods ...............	$44.03
	(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ................	$38.08
	(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods .............	$64.97
	(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ................	$79.02
	(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods .............	$98.53
	Hex Coupling Nuts for Rods .........................................................	$2.86
	Above noted delivery times determined by delivery time of model ordered.

Shipping Schedule

Solid Blue or Black prices with Brown shading indicates items available for 3-Day shipment.

Solid Blue or Black prices indicates items available for 2-Week shipment.

Solid Green model numbers or prices indicate items available for 24-Hour Shipment.

Prices coded in light blue call for lead time.

Prices coded in red ship in 4-Weeks.

POLY-TIER SUPPORTS

PRICES FOR COMPLETE
SUPPORT INCLUDE:

IMPORTANT NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.

• Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
conveyor)
• "U" Brackets
• Single Width Conveyor Only

CAPACITY DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs

(2) TIER POLY-TIER SUPPORTS
36"	$201.94
42"	$207.54
48"	$213.13
54"	$218.72
60"	$224.32
66"	$229.91
72"	$235.38
78"	$240.98
84"	$246.57
90"	$252.16
96"	$257.75
102"	$263.35
108"	$268.82
114"	$274.77
120"	$280.01

(3) TIER POLY-TIER SUPPORTS
36"	$284.77
42"	$290.36
48"	$295.95
54"	$301.55
60"	$307.14
66"	$312.73
72"	$318.33
78"	$323.80
84"	$329.39
90"	$334.99
96"	$340.58
102"	$346.17
108"	$351.76
114"	$357.24
120"	$362.83


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

ELECTRICAL CONTROLS AND DRIVE SECTION

MANUAL START SWITCH or
SAFETY DISCONNECT

LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER

#032.1014.........................................

$150.06

#033.2032 & #033.2072..................$203.25
Nema 4

"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)

LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER

#033.2033& #033.2072...................$233.95
Nema 4

REVERSING DRUM SWITCH

#032.103..........................................

$446.25

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase

PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

REMOTE CONTROL ROD

#032.210.........................................$144.70
115 Volt AC, two wire with ground, 30mm dia.,
10mm range

Price per foot of bed length "L"...........$6.78
Use with standard Reversing Drum Switch,
ONLY.

#032.211.........................................$171.12
24 Volt DC, two wire with ground, 30mm dia.,
10mm range

FOOT SWITCH WITH GUARD

#032.200........................................... $190.52
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.

PHOTO EYE, ON-OFF TYPE

#033.2122......................................$549.78
115 Volt, relay output, light or dark energized,
and includes Reflector.

POWER CORD AND PLUG (20')

DUAL TIME DELAY MODULE

#033.2172.......................................$191.59
For #033.2122 Photo Eye (.5 to 10 seconds
On), (.5 to 10 seconds Off)

POWER CORD WITH PLUG ONLY 20' LONG
Model No.	Voltage	HP Rating	Prices
EA-039-1A	115/1	1/2-3/4	$75.09
EA-039-2A	115/1	1	$75.09
EA-039-3A	115/1	1 1/2	$109.24
EA-039-4A	230/1	1/2-1	$75.09
EA-039-5A	230/1	1 1/2-2	$77.23
EA-039-6A	208-230/3	1/2-2	$125.90
EA-039-7A	460/3	1/2-2	$125.90

POWER CORD WITH PLUG 20' LONG WITH MANUA
Model No.	Voltage	HP Rating	Prices
EA-039-1B	115/1	1/2-3/4	$206.35
EA-039-2B	115/1	1	$233.00
EA-039-3B	115/1	1 1/2	$266.32
EA-039-4B	230/1	1/2-1	$206.35
EA-039-5B	230/1	1 1/2-2	$233.00
EA-039-6B	208-230/3	1/2-2	$255.85
EA-039-7B	460/3	1/2-2	$255.85

MOUNTING BRACKETS FOR PHOTO
EYE #033.2122

B-05165...........................................$83.06

AIR PRESSURE SWITCH

#094.191........................................$487.07
Nema 4

EMERG. STOP PULL CORD SWITCH

#032.285 with 032.2851 Turnbuckle
...........................................................$490.40
Nema 4

"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE

#032.281...one side.................$5.24 per / ft.
both sides............$10.47 per / ft.

EMERGENCY PUSH BUTTON

#032.284..........................................$158.27
Nema 4

Control cable for the Emergency Stop to be
mounted and wired to the magnetic starter,
supply cable and hardware.... $3.21 per foot.

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE

#032.212 (100mm range, 3.94")......$206.70
#032.2125 (200mm range, 7.87")....$206.70
#033.218 (400mm range, 15.74")....$206.70

NOTE: PRICING LISTED NOT MOUNTED
OR WIRED

"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC

#033.2128 with 032.21122 Cable.....$315.71
#032.21122 (Cable Only)..................$50.81


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.

AC VARIABLE SPEED DRIVE ADD-ON PRICES

REPLACEMENT CONTROLLER

AC VARIABLE SPEED DRIVES (ALL MOTORS ARE ENERGY EFFICIENT 3 PHASE)
SINGLE PHASE CONTROLLER INPUT
H.P.	ADD ON PRICE 115 VOLT		ADD ON PRICE 208/230 VOLT
1/2	EA-VSC-12-10		EA-VSC-12-12
Price	$1,290.08		$1,090.16
1	EA-VSC-12-11		EA-VSC-12-13
Price	$1,508.21		$1,335.66
2	N/A		EA-VSC-12-14
Price	~		$2,006.22
THREE PHASE CONTROLLER INPUT
H.P.	ADD ON PRICE 208/230 VOLT	ADD ON PRICE 460 VOLT		ADD ON PRICE 575 VOLT
1/2	EA-VSC-01-15	EA-VSC-01-18		EA-VSC-12-29
Price	$1,239.27	$1,420.98		$1,937.44
1	EA-VSC-01-16	EA-VSC-01-19		EA-VSC-12-29
Price	$1,411.82	$1,588.17		$1,981.11
2	EA-VSC-01-17	EA-VSC-01-20		EA-VSC-12-30
Price	$2,022.41	$2,165.92		$2,599.79

AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size	115 Volt		208/230 Volt
1/2	VSC-12-10		VSC-12-12
Price	$1,051.01		$838.00
1	VSC-12-11		VSC-12-13
Price	$1,214.99		$980.08
2	N/A		VSC-12-14
Price	~		$1,264.26
THREE PHASE CONTROLLER INPUT
Motor Size	208/230 Volt	460 Volt	575 Volt
1/2	VSC-01-15	VSC-01-18	VSC-12-29
Price	$1,102.65	$1,167.03	$1,542.36
1	VSC-01-16	VSC-01-19	VSC-12-29
Price	$1,113.25	$1,264.26	$1,542.36
2	VSC-01-17	VSC01--20	VSC-12-30
Price	$1,394.20	$1,458.82	$1,876.87

REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS

HP	Part No.	Price
1/2	032.351 230/460	$583.58
1	032.353 230/460	$632.96
2	032.355 230/460	$657.83
1/2	032.3512 575	$1,041.37
1	032.3532 575	$1,096.70
2	032.3552 575	$1,194.64

OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)

$272.63

Brake Relay Kit (EA-068A)..............................

$380.92

IMPORTANT NOTES...

• Add on price includes standard motor deduct.
• 2 HP Add On Price includes 5AC reducer upgrade.
• All above motors are 230 / 460 / 575 Volt, 3 Phase.
• All above V/S Drive Kits include NEMA 1 / IP30
Junction Box, Controller and Motor.
• Good for cycle rates of up to 15 cycles per minute, at
1/2 second ramp time, with a maximum speed of 250
FPM.
• Drawing No. DG-001146.

• When AC Variabl Speed Controller is used with a
Brake Motor, A Brake Relay Kit (EA-068A) is
required. Add an additional $380.92 for this option.)

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE

Part No.	Description	Price
EA-VSC-01-CB	2 HP Electronic Clutch-Brake Kit	$3,670.79

OPTIONAL: Mounting and Wiring Add-on . .
(mounted close to the motor)

$272.63

KIT INCLUDES

Part No.	Description
VSC-01-20	AC Variable Speed Controller, 460 Volt, 3 Phase
032.345	2 HP 460 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets

IMPORTANT NOTES

• Good for cycle rates of up to 60 cycles per minute.
• 1/10 second Accel and Decel time, with 350 FPM
Maximum Speed.
• 230 or 460 Volt Only, Other Voltages, Contact us.
• Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
• Price Includes 5AC Reducer and #60 Chain and
Sprockets

Part No.	Description
VSC-01-17	AC Variable Speed Controller, 230 Volt, 3 Phase
032.345	2 HP 230 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click the Model No. of the item you wish to purchase.

THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)

An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.

THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	MOTOR DUTY	NON-REVERSING					REVERSING
H.P.	MOTOR DUTY	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE
1/2	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B25	EN-46B16	EN-57B10	$951.88	ER-20B40	ER-23B25	ER-46B16	ER-57B10	$1,158.11
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
			EN-23B16	EN-46B10				ER-23B16	ER-46B10
1	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B40	EN-46B25	EN-57B16		ER-20B40	ER-23B40	ER-46B25	ER-57B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
1-1/2	GEARMOTORS	EN-20C10	EN-23B63	EN-46B40	EN-57B25		ER-20C10	ER-23B63	ER-46B40	ER-57B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
2	STANDARD EASY CLEAN ENERG. EFF.	EN-20C10	EN-23C10	EN-46B40	EN-57B40		ER-20C10	ER-23C10	ER-46B40	ER-57B40
			EN-23C10	EN-46B40				ER-23C10	ER-46B40
			EN-23B63	EN-46B40				ER-23B63	ER-46B40

SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	NON-REVERSING		REVERSING		NON-REVERSING		REVERSING
	115 VOLT	PRICE	115 VOLT	PRICE	230 VOLT	PRICE	230 VOLT	PRICE
1/2	EN-1SC10	$833.00	ER-1SC10	1064.93	EN-2SB63	$969.85	ER-2SB63	$1,181.91
1	EN-1SC16	$833.00	ER-1SC16		EN-2SC10		ER-2SC10
1-1/2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10
2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10


• Manual Start-Stop Switch Kit			• Start-Stop Push Button Kit, Remote Mounted
	EA-000001 ......................................	$170.53		EA-000002.......................................	$150.18
	Includes: 032.1014 Manual Start Switch, Nema 1, B-21467 Mounting Bracket with Mounting Hardware			Includes: 033.1955 Push Button Station, One Direction, Nema1, B-21467 Mounting Bracket with Mounting Hardware

• Forward-Reverse-Stop Push Button Kit, Remote Mounted

			• Up-Down-Stop Push Button Kit, Remote Mounted
	EA-000003.......................................	$300.24	• Up-Down-Stop Push Button Kit, Remote Mounted
	Includes: 033.1965 Push Button Station, Reversing, Nema1, B-21467 Mounting Bracket with Mounting Hardware			EA-000004.......................................	$300.24
				Includes: 033.1975 Up Down Stop Push Button Station, Reversing, Nema 1, B-21467 Mounting Bracket with Mounting Hardware


			Order Online, by Phone, or by E-Mail
			~ Add items to your online shopping cart ~ Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station				• “Start-Stop”Push-button Station
033.1955			$138.04		033.195.................................................	$100.32
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Fwd-Rev-Stop” Push-button Station				• “Fwd-Rev-Stop”Push Button Station
033.1965			$270.13		033.196..................................................	$345.81
Remote mounted, Nema 1					To be mounted in Mag Starter Cover

• “Up-Down-Stop” Push-button Station				OPTIONAL STARTER CONTROLS
033.1975			$248.00	OPTIONAL STARTER CONTROLS
033.1975			$248.00	• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1				• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1					EA-011 ............................................ Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), and a Control Circuit Transformer (As Required), & Pushbutton Station (033.195).	$1,880.20
						$1,880.20

• Control Cable for the Push button to be mounted and
wired, supply cable, and hardware........			$3.33

IMPORTANT NOTES
• Control Circuit Transformer Included for 115 Volt Control Voltage. • Above starters are in Nema 3, 4 and 12 Enclosures. • The starters included Safety Disconnect, Overload Relay, and Aux. Contacts as required. • IF AN ORDER IS SUPPLIED LESS MOTOR, AND IS SUPPLYING ANY ELECTRICAL CONTROLS, THEN MOTOR HP, VOLTAGE, PHASE, AND FULL LOAD CURRENT MUST BE STATED ON THE ORDER. • PRICING LISTED IS NOT MOUNTED OR WIRED.

				• Auto Restart Control, 1 Phase, Non-Reversing
					EA-012 (115 Volt) ........................... EA-017 (230 Volt) ........................... Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), Pushbutton Station (033.195), and (230 V. Only) a Control Circuit Transformer (As Required). Note: Above Price does NOT include Photo Eye Mounting Bracket.	$1,787.62
						$1,989.09

• Add on	$136.37	for the above Push Buttons
to be Mounted.
• Add on	$272.63	for the above Starters to be
• Add on	$272.63	for the above Starters to be
Mounted and Wired.
Mounted and Wired.				• Mounting Brackets for photo eye
• Add on	$408.53	for the above Starters and			#033.2122 B-05165 ..............................................
Push Button Stations to be Mounted and Wired.						$83.06


EZ-LOGIC® COMPONENTS

	While featuring the same EZLogic® familiarity, GEN3 incorporates new technologies for ease of installation, operation, and maintenance.

ZONE CONTROLLERS



	Retro-Reflective Type Zone Controller
	Zone controller including mounting base and unitized retro-reflective transducer. 032.501 ..........................................................................................................................
		$204.68

	Diffuse Type Zone Controller
	Zone controller including mounting base and unitized diffuse transducer with adjustable sensitivity (through programming).
	032.502 .................................. Add-On ............................................Per Zone ......................	$18.92
	032.502 .................................. Replacement ...........................................................................	$223.60

	Enhanced Retro-Reflective Zone Controller
	Same as standard, plus used for IOP communication, and addressable remote access.
	032.505 .................................. Add-On ............................................Per Zone ...................	$132.33
	032.505 .................................. Replacement ........................................................................	$252.28

	Enhanced Diffuse Zone Controller
	Same as standard, plus used for IOP communication, and addressable remote access.
	032.506 .................................. Add-On ............................................Per Zone ...................	$151.13
	032.506 .................................. Replacement ........................................................................	$269.30

	Remote Zone Controller
	Zone controller including mounting base. Connectorized for attaching any remote transducer.
	032.504 .................................. Replacement ........................................................................	$204.68
	Enhanced Remote Zone Controller
	Enhanced zone controller including mounting base. Connectorized for attaching any remote transducer. Same as standard, plus used for IOP communication, and addressable remote access.
	032.507 .................................. Replacement ........................................................................	$226.22


TRANSDUCERS (SENSORS)

Remote Diffuse Transducer (Narrow Beam)
Has narrow beam for use with close roller centers. Attaches to any remote zone controller and allows transducer to be mounted separate from controller.
032.513 .................................. Replacement ..................................	$93.89

CORDSETS
CORDSETS

Zone Controller Cordset (Zone to Zone Communication) Available for the following zone lengths:


	12" .......................................................032.551..................................................			$50.81
	18" .......................................................032.552..................................................			$50.81
	24" .......................................................032.553..................................................			$50.81
	30" .......................................................032.554..................................................			$50.81
	36" .......................................................032.555..................................................			$50.81
	48" .......................................................032.556..................................................			$54.50
	60" .......................................................032.557..................................................			$56.41
	72" .......................................................032.558..................................................			$75.09

Zone Controller Screw-On Cordset (NEMA 4X Zone to Zone Communication for Wash Down Application) Available for the following zone lengths:

	12" .......................................................032.5515..................................................			$50.81
	18" .......................................................032.5525..................................................			$50.81
	24" .......................................................032.5535..................................................			$50.81
	30" .......................................................032.5545..................................................			$50.81
	36" .......................................................032.5555..................................................			$50.81
	48" .......................................................032.5565..................................................			$59.14
	60" .......................................................032.5575..................................................			$60.69
	72" .......................................................032.5585..................................................			$78.66

Infeed Zone Terminator
Terminates zone to zone communication at infeed zone.
032.550 .................................. Each .............................................................			$50.81

Mounting Base
Use to mount any Zone Controller.
032.517 .............. Each ..............		$18.80

IOP

IOP
Provides 27VDC, 100 watt power for EZLogic“ accumulation system. Requires 120 VAC or 230 VAC single phase input. Operates up to 50 zones (25 zones each side of IOP).– contains slots for 4 input/ output boards. Requires enhanced zone controllers to communicate with input/output boards.
032.582 .................................. Each .......................	$623.32


IOP "T" Cable
Required to deliver power and IOP communication from IOP to zone controllers. Max. of 25 zones per each branch of T.
Standard Push-On 032.559 .....Each ..........................	$69.26
NEMA 4X Screw-On 032.5595 .....Each ..................	$73.30


I/O Board
Plugs into slot in IOP to provide two input/output connections. Requires enhanced controller to receive signal.
032.583 .................................. Each ...............................		$90.20

CONFIGURATION/DIAGNOSTIC COMPONENTS

Push Button Programmer
Plugs into auxiliary port of any controller to configure certain features of controller. Required for customization of factory default settings.
032.535 .................................. Each ...............................	$168.86


Programming Kit for PC and PC Adaptor
Used to connect PC USB port to auxiliary port of any controller. Includes GenesisTM configuration software. Used to configure all features of controller. Required for customization of factory default settings.
K-01554 .................................. Each ...............................	$212.53

AUXILIARY COMPONENTS

Auxiliary I/O Module

Plugs into auxiliary port of any controller - used to provide photo eye output or to accept a voltage type input.
032.532 ....................................................	$75.09

Auxiliary Input Cable
Attaches to any zone controller. Used for zone stop input, wakeup eye input, or slug input. Available in 3 and 10 ft. lengths.

3 ft. ..........................032.532 ....................................Each ..................		$32.25
10 ft. ..........................032.564 ....................................Each ..................		$32.96


Zone Actuation Module “ZAM” (Alternate Drive) Provides NPN, PNP, or dry contact output from zone controller.
032.531 ......................................................Each................................		$75.09

Retro-Reflective Wake-up Eye Plugs into auxiliary port of any controller to send wake-up signal.
032.591 ......................................................Each................................		$127.81

Diffuse Wake-up Eye Plugs into auxiliary port of any controller to send wake-up signal.
032.592 ......................................................Each................................		$127.81


Retro-Reflectors
2.18” Dia. 032.218 .....................................Each ...............................		$2.02
3” Dia. 033.2132 ........................................Each ................................		$3.57

Connector Covers
Upstream Connector Cover 032.010 .............Each ...............................		$4.40
Downstream Connector Cover 032.011..........Each ...............................		$4.40

CABLE COMPONENTS

Power Isolation Cable
Required to isolate DC power when joining conveyors w/ separate IOPs utilizing no more than one set of I/O boards.
Standard Push-On ................... 032.562 ....................Each .............		$41.77
NEMA 4X Screw-On ............. 032.5625 .......................................		$47.60

IOP Isolation Cable
Required to isolate DC power and input/output signals when joining two conveyors with separate IOPs, both utilizing I/O boards.

Standard Push-On ................... 032.570 ....................Each .............		$41.77
NEMA 4X Screw-On ............. 032.5705 .......................................		$47.60

Extension Cable (Zone to Zone Communication)
Available in 3 and 10 ft. lengths. Used to extend zone controller cable when necessary.
Standard Push-On 3 ft.................... 032.560 ....................Each .........		$44.86
Standard Push-On 10 ft.................... 032.561 ....................Each ........		$58.19
NEMA 4X Screw-On 3 ft.............. 032.5605 ....................................		$47.60
NEMA 4X Screw-On 10ft.............. 032.5615 ..................................		$66.52

Nano Extension Cable
Used to extend auxiliary devices or remote transducer cable. Available in the following lengths:

1 ft ........................... 032.565 ...........................................Replacement .................			$33.80
2 ft ........................... 032.566 ...........................................Replacement .................			$35.82
3 ft ........................... 032.567 ...........................................Replacement .................			$37.60
6 ft ........................... 032.568 ...........................................Replacement .................			$43.20

Power Splitter
Used to connect two conveyors located side by side to one IOP. Requires 2 power supply T cables. Maximum total of 50 zones.
032.569 ...............................Each ........................	$44.98

SPECIAL USE COMPONENTS

Diffuse Type Zone Controller
Zone controller including mounting base and unitized diffuse transducer with adjustable sensitivity (through programming). 24 in. cable.
032.503 .......................................Each ................................	$225.27


Remote Retro-Reflective Transducer
Attaches to any remote zone controller and allows transducer to be mounted separate from controller.
032.511 .............................................Each ..............................	$56.41


Remote Diffuse Transducer
Attaches to any remote zone controller and allows transducer to be mounted separate from controller.
032.512 ............................................Each ..............................	$75.09


Remote Retro-Reflective Transducer (Dual with T Cable)
For use in dual head applications. Attaches to any remote zone controller and allows addition of second remote transducer.

032.514 ..........................................Replacement ..................	$150.18

Remote Diffuse Transducer (Dual with T Cable)
For use in dual head applications. Attaches to any remote zone controller and allows addition of second remote transducer.
032.515 ...................................................Replacement ..............	$187.78

Remote Diffuse Transducer (Narrow Beam, Dual with T Cable)
For use in dual head applications. Has narrow beam for use with close roller centers. Attaches to any remote zone controller and allows addition of second remote transducer.
032.516 ...................................................Replacement ..............	$225.27

Accumulating Conveyor, Plastic Belt Conveyor, Zero Pressure, Conveyor, Live Roller Conveyors, Powered Live Roller, Powered
Turntable, Conveyors, and Roller Conveyors from your source for material handling equipment.

Back to Product Category

Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart

Accumulating Conveyor, Plastic Belt Conveyor, Zero Pressure, Conveyor, Live Roller Conveyors, Powered Live Roller, Powered Turntable, Conveyors, and Roller Conveyors from your source for material handling equipment.

Accumulating Conveyor, Plastic Belt Conveyor, Zero Pressure, Conveyor, Live Roller Conveyors, Powered Live Roller, Powered
Turntable, Conveyors, and Roller Conveyors from your source for material handling equipment.