Back to Product Category
SORRY
THIS MODEL HAS BEEN DISCONTINUED.
CONTACT US FOR REPLACEMENT PARTS. |
MODEL
CCAC |
HORIZONTAL
POWER CONVEYOR
(Accumulating Type) |
|
|
|
|
|
Plastic Belt
High Speed Curve
Slave Driven From CCEZ
Adjustable MS-Type
Floor Supports Available |
|
|
|
|
|
The Model CCAC
is a horizontal plastic belt curve
conveyor which is normally slave driven from the
Model CCEZ for accumulating 12 & 24 packs
of canned beverages where high speeds and large
through-puts are required. |
|
|
|
|
|
HOW
IT WORKS |
|
The
conveyor consists of one accumulation zone the entire length of the curve.
It is designed to be slave driven from
the infeed end of the Model CCEZ when a turn is required. The plastic belt
is driven from the Model CCEZ by
means of an air operated friction clutch and chain. When the infeed zone
of the Model CCEZ is accumulated, an air
signal is used to engage the clutch, therefore stopping the curve. |
|
|
|
|
OPTIONAL
EQUIPMENT |
FLOOR
SUPPORTSMS Type floor supports are
available with a wide range of adjustment. Specify top
of belt or roller elevation. One support required at
every bed joint and ends of conveyor. Holes in feet for
lagging to floor. Knee braces recommended above
MS-6 support.
END DRIVEMotor and reducer may be supplied
when slave drive is not desired. |
O-RING
DRIVE CHAINWith sealed in lubricant
(Recommended for applications that do not permit
regular lubrication).
POLY-TIER SUPPORTS36 in. to 120 in. support
heights in 6 in. increments. Knee braces supplied.
CEILING HANGERS5/8 in. dia. x 8 ft. long
unplated fully threaded rods. Other lengths and gal-
vanized rods available. |
|
|
|
Shipping
Schedule |
|
Solid Blue or Black prices with Brown shading
indicates items available for 3-Day shipment. |
|
Solid Blue or Black prices indicates items available for 2-Week shipment. |
|
Solid
Green model numbers or prices indicate items available for 24-Hour Shipment. |
|
Prices
coded in light blue call for lead time. |
|
Prices
coded in red ship in 4-Weeks. |
|
|
|
|
|
PRICES
FOR COMPLETE CONVEYOR INCLUDE: |
|
|
|
|
|
6" Wide Table Top Belt
13 x 12 Ga. Channel Frames
Slave Driven from Infeed End of Model CCEZ Via
Air Operated Friction Clutch and #50 Roller
Chain(Additional Slave Shaft Supplied When
Driving From Existing CCEZ) |
|
Curves
have 12 Long Infeed Tangent and 36
Long Discharge Tangent
Less Supports |
|
|
|
Between Rail Width |
13" |
Overall Frame Width |
16" |
30º |
$4,826.64 |
45º |
$4,976.58 |
90º |
$5,998.79 |
180º |
$8,978.55 |
|
|
|
|
|
NOTE: Ramp Speed Start required for smooth start-up. |
|
NOTE: When ordering, specify Right
or Left Hand unit |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PRICES
FOR OPTIONAL EQUIPMENT |
|
|
|
|
|
|
FLOOR SUPPORTS |
TANGENTS |
|
Longer
Tangents Available ............... Contact
us |
|
|
|
|
Not
Included in Base Price. Use Chart Below for
Required Elevation. |
|
|
MOTORS |
|
|
"MS" SUPPORT |
Model No. |
Adjustment to Top of Roller |
Price each |
*MSL-1 |
12-1/8" to 13-1/8" |
$37.96 |
*MSL-2 |
13-1/8" to 14-7/8" |
$37.96 |
*MSL-3 |
14-7/8" to 17-1/2" |
$37.96 |
*MS-1 |
17-1/8" to 18-7/8" |
$37.96 |
*MS-1.2 |
18-1/8" to 19-7/8" |
$37.96 |
*MS-1.4 |
19-1/8" to 20-7/8" |
$37.96 |
*MS-2 |
20-1/8" to 23-1/8" |
$39.15 |
MS-3 |
22-3/4" to 25-3/4" |
$43.08 |
MS-4 |
25-3/4" to 31-3/4" |
$49.74 |
MS-5 |
29-3/4" to 35-3/4" |
$51.77 |
MS-6 |
33-3/4" to 45-3/4" |
$57.12 |
MS-7 |
43-3/4" to 55-3/4" |
$84.37 |
MS-8 |
55-3/4" to 67-3/4" |
$96.39 |
MS-9 |
67-3/4" to 79-3/4" |
$105.55 |
MS-10 |
79-3/4" to 91-3/4" |
$120.19 |
MS-11 |
89-3/4" to 101-3/4" |
$133.04 |
MS-12 |
101-3/4" to 113-3/4" |
$139.23 |
|
Extra
Motor Price for OTHER THAN: 1 HP
208/230/460V3 Ph.60 Hz.Energy Efficient.
Speed affects horsepower requirements |
|
|
|
H.P. REQ. |
115 V 1
Ph.-60 Hz. |
208/230/460 V 1
Ph.-60 Hz. |
208/230/460 V 3
Ph.-60 Hz. |
1 Ph. AC Controller |
1 Ph. AC Controller |
3 Ph. AC Controller |
1 |
N/C |
N/C |
N/C |
2 |
N/A |
$790.87 |
$790.87 |
|
|
|
|
END DRIVE |
|
In
lieu of slave drive ..........................No
Add-on |
|
.........................................................No
Deduct |
|
|
|
GALVANIZING |
|
Contact
us. |
|
|
|
|
|
*Less
than 24-1/2" top of belt elevation-Side Mounted
Drive Required.
Note: MS-7 to MS-12: Knee Bracess included in price. |
|
|
Extra
Knee Braces.....per pair.................
Single Center Leg (MS-6 and below) each
Single Center Leg (MS-7 and above) each |
$18.92 |
|
|
$39.15 |
|
|
$48.67 |
CEILING HANGERS |
|
Ceiling
Hanger Brackets with (2) 5/8 dia. x 8-0 long unplated
fully threaded rods ...................................................................... |
|
|
$92.82 |
Ceiling
Hanger Brackets with (2) 5/8 dia. x 8-0 long galvanized
fully threaded rods ....................................................................... |
|
$100.08 |
Ceiling
Hanger Brackets with (2) 5/8 dia. x 10-0 long unplated
fully
threaded rods................................................................................ |
|
$102.34 |
Ceiling
Hanger Brackets with (2) 5/8 dia. x 10-0 long galvanized
fully threaded rods................................................................................. |
|
$131.50 |
Ceiling
Hanger Brackets with (2) 5/8 dia. x 12-0 long unplated
fully threaded rods................................................................................. |
|
|
|
|
$134.47 |
|
Ceiling
Hanger Brackets with (2) 5/8 dia. x 12-0 long galvanized
fully threaded rods.................................................................................. |
|
|
$154.70 |
|
Ceiling Hanger
Brackets, Less Rods Only .................................... |
$56.17 |
|
Extra Length Rods: |
|
|
(2) 8-0
long x 5/8 dia. unplated fully threaded rods .................. |
$34.27 |
|
(2) 8-0
long x 5/8 dia. galvanized fully threaded rods ............... |
$44.03 |
|
(2) 10-0
long x 5/8 dia. unplated fully threaded rods ................ |
$38.08 |
|
(2) 10-0
long x 5/8 dia. galvanized fully threaded rods ............. |
$64.97 |
|
(2) 12-0
long x 5/8 dia. unplated fully threaded rods ................ |
$79.02 |
|
(2) 12-0
long x 5/8 dia. galvanized fully threaded rods ............. |
$98.53 |
|
Hex Coupling Nuts
for Rods ......................................................... |
$2.86 |
|
Above
noted delivery times determined by delivery time of model ordered. |
|
|
|
POLY-TIER SUPPORTS |
|
PRICES
FOR COMPLETE
SUPPORT INCLUDE: |
|
|
|
IMPORTANT
NOTES
Check for Clearance
Specify type of conveyor to be used.
Use in place of LS or MS Supports only. |
Painted Steel Support Legs
Adjustable Cross pipe Assembly
Knee Braces (1 set per level of
conveyor)
"U" Brackets
Single Width Conveyor Only |
|
|
|
|
|
|
|
|
|
|
CAPACITY
DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs |
|
|
|
|
|
|
|
|
|
|
(2) TIER POLY-TIER SUPPORTS |
36" |
$201.94 |
42" |
$207.54 |
48" |
$213.13 |
54" |
$218.72 |
60" |
$224.32 |
66" |
$229.91 |
72" |
$235.38 |
78" |
$240.98 |
84" |
$246.57 |
90" |
$252.16 |
96" |
$257.75 |
102" |
$263.35 |
108" |
$268.82 |
114" |
$274.77 |
120" |
$280.01 |
|
|
(3) TIER POLY-TIER SUPPORTS |
36" |
$284.77 |
42" |
$290.36 |
48" |
$295.95 |
54" |
$301.55 |
60" |
$307.14 |
66" |
$312.73 |
72" |
$318.33 |
78" |
$323.80 |
84" |
$329.39 |
90" |
$334.99 |
96" |
$340.58 |
102" |
$346.17 |
108" |
$351.76 |
114" |
$357.24 |
120" |
$362.83 |
|
|
|
|
|
Accumulating Conveyor, Conveyor,
Plastic Belt Conveyor, Zero Pressure, Curve, Power Conveyor, Powered Live
Roller, Powered
Turntable, Conveyors, and Roller Conveyors from your source for material
handling equipment. |
Back to Product Category
|