Back to Product Category
|
MODEL
25-CRR
|
|
CHAIN DRIVEN LIVE
ROLLER CONVEYOR
(Roll-to-Roll Type)
|
 |
|
The
heavy design of the 25-CRR
allows it to be used for conveying
higher load capacities such as loaded
pallets and drums. Chain driven rollers
make it ideal for conveying oily parts
in bottling and steel industries. |
|
|
|
15 Bed Widths
Center Drive
Reversible
Chain Driven Rollers
Adjustable HSN-Type Floor Supports
Available |
|
|
|
|
|
 |
|
|
|
|
STANDARD
SPECIFICATIONS
|
BED
- Roller bed with 2-1/2 in. dia. x 11 ga. unplated
tread rollers spaced every 4 in. with No. 40 roller chain;
5 in. with No. 50 roller chain. No. 60 roller chain used on
3 in., 3-3/4 in., 6 in., and 7-1/2 in. roller centers only. Tread
rollers mounted in 4 in. x 4 ga. powder painted formed steel
channel on side opposite chain guard and 6 in. x 4 ga.
powder painted formed steel channel on chain guard side.
NOTE: 3 in. roller center tread rollers mounted in 4 in.
channel each side. |
|
BEARINGS–Sealed,
pre-lubricated ball bearings. |
|
|
|
SPEED
REDUCTION–Sealed worm gear C-Face
speed reducer. |
|
|
|
MOTOR–1
HP–208/230/460/575V–3 Ph. 60 Hz.
Totally Enclosed C-Face. |
|
|
|
CONVEYING
SPEED–Constant 30 FPM. |
|
|
|
|
|
CENTER
DRIVE- Can be placed in any section of
conveyor length, specify. Chain guard located on left hand
side. |
|
|
|
CAPACITY–Maximum
load per linear foot of conveyor
300 lbs. with supports on 10 ft. centers, 1000 lbs. with
supports on 5 ft. centers. Contact us for capacity
of No. 40 chain, 4 in. roller centers. NOT TO EXCEED
CAPACITY IN CHART. |
|
|
| DRIVE
CHAIN–No. 40, 50 or 60 roller chain. |
|
|
|
CHAIN
GUARD–Formed steel, upper and lower chain
guard mounted to top and bottom of channel frame to totally
enclose drive chains. |
|
|
|
|
FLOOR
SUPPORTS–Now supplied as optional
equipment. |
|
|
|
|
|
|
 |
|
|
|
|
|
LOAD CAPACITY CHART @ 30 FPM
|
|
HP
|
TOTAL LOAD (LBS.)
|
|
UP TO 50'
|
UP
TO 100'
|
|
1
|
9000
|
6000
|
|
2
|
22000
|
18000
|
|
|
|
NOTE:
Capacities are calculated on 5" Roller Centers with
#50 Chain. |
|
|
|
|
|
|
|
GUARD
REMOVED TO ILLUSTRATE ROLL-TO-ROLL DRIVE CHAIN WARNING:
Do not operate conveyor with Chain Guard removed. |
|
|
|
|
OPTIONAL
EQUIPMENT
|
FLOOR
SUPPORTS–HSN Type floor supports are
available with a wide range of adjustment. Specify top
or roller elevation. One support required at every bed
joint and ends of conveyor. Holes in feet for lagging to
floor. Knee braces recommended above HSN-3 support. |
|
CHANNEL
END STOP–6” x 8.2 lb. structural channel
end stop. |
|
|
|
ROLLERS
SET LOW–Tread rollers mounted in 5 in.
x 4 ga. formed steel channel frame to form 5/8 in. high
guard rails. Also available in 5 in. x 6.7 lbs. structural
channel frame (welded). Specify. |
|
|
CONVEYING
SPEED–Other constant and variable
speeds. V-belt supplied on speeds under 12 FPM (1 HP).
NOTE: Capacity affected with speed change. |
|
|
|
|
CHAIN
CROSSOVER–Separate 3-roller section
moves driving chain from one side of conveyor to other.
Offset-style adds 12 in. to OAL of conveyor with No.
40 chain, 15 in. with No. 50 chain & 18 in. with No.60
chain. |
|
|
TOP
SIDE MOUNTED DRIVE–Motor reducer unit
mounted to side of conveyor with drive chain through top
of chain guard. Specify clearances. Minimum elevation top
of rollers 6 in. |
|
|
|
|
TRANSFERS–Chain
transfers available. See
Accessory section. |
|
|
V-BELT
DRIVE–V-belt supplied between motor and
reducer. |
|
|
|
|
MOTORS–Energy
efficient, single phase, brake motor,
other characteristics. 2 HP maximum. |
|
|
O-RING
DRIVE CHAIN–With sealed in lubricant
(Recommended for applications that do not permit regular
lubrication). |
|
|
|
|
ELECTRICAL
CONTROLS–Non-reversing mag-
netic starter – pushbutton stations. AC variable frequency
drive. |
|
|
| FRAMES–4
in. x 5.4 lb. structural channel (welded). |
|
|
|
|
|
|
GUARD
RAILS–Fixed angle (2 in. high x 1/4 in. steel)
guard bolts to top flange of channel opposite chain guard. |
|
|
|
| PRICES
FOR COMPLETE CONVEYOR INCLUDE: |
•
2-1/2” Dia. x 11 Ga. Roller Mounted in a 4” x 4 Ga. Formed
Channel Frame
• No. 40 *, No. 50, or No. 60 Roller Chain
• “C” Face Speed Reducer—Sealed Worm Gear
• 1 HP–“C” Face Totally Enclosed Motor (Specify
Exact Voltage)
• Totally Enclosed Chain Guard
• 30 FPM Conveying Speed
• Less Electrical Controls
• Less Supports |
|
|
4 in., 5 in., 6 in. and 7-1/2 in. Roller Centers
|
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
|
Between Rail Width |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
43" |
47" |
51" |
55" |
61" |
67" |
|
Overall Frame Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4 |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4 |
46-1/4" |
50-1/4" |
54-1/4" |
58-1/4" |
64-1/4" |
70-1/4" |
*4" Centers 10' Length-
O.A. Per Foot |
No. 40 Chain |
$3,267 |
$3,315 |
$3,360 |
$3,408 |
$3,456 |
$3,550 |
$3,596 |
$3,690 |
$3,738 |
$3,831 |
$3,925 |
$4,020 |
$4,113 |
$4,253 |
$4,395 |
|
$245.03 |
$248.39 |
$251.63 |
$255.10 |
$258.46 |
$265.17 |
$268.53 |
$275.12 |
$278.60 |
$285.19 |
$291.91 |
$298.62 |
$305.33 |
$315.40 |
$325.35 |
5" Centers 10' Length-
OA Per Foot |
No. 50 Chain |
$3,208 |
$3,250 |
$3,294 |
$3,336 |
$3,381 |
$3,466 |
$3,509 |
$3,595 |
$3,637 |
$3,723 |
$3,810 |
$3,896 |
$3,982 |
$4,111 |
$4,239 |
|
$188.57 |
$192.41 |
$196.48 |
$200.32 |
$204.40 |
$212.31 |
$216.14 |
$224.06 |
$227.89 |
$235.80 |
$243.60 |
$251.51 |
$259.42 |
$271.17 |
$282.92 |
6" Centers 10' Length-
OA Per Foot |
No. 60 Chain |
$3,138 |
$3,176 |
$3,210 |
$3,248 |
$3,285 |
$3,358 |
$3,395 |
$3,468 |
$3,505 |
$3,578 |
$3,650 |
$3,725 |
$3,798 |
$3,908 |
$4,017 |
|
$168.55 |
$171.91 |
$175.14 |
$178.50 |
$181.98 |
$188.57 |
$192.05 |
$198.64 |
$202.00 |
$208.71 |
$215.30 |
$222.14 |
$228.85 |
$238.80 |
$248.87 |
7-1/2" Centers 10' Length-
OA Per Foot |
No. 60 Chain |
$2,824 |
$2,857 |
$2,888 |
$2,920 |
$2,951 |
$3,016 |
$3,049 |
$3,112 |
$3,143 |
$3,207 |
$3,270 |
$3,335 |
$3,399 |
$3,495 |
$3,589 |
|
$139.18 |
$141.94 |
$144.58 |
$147.33 |
$149.97 |
$155.36 |
$158.12 |
$163.52 |
$166.15 |
$171.55 |
$177.06 |
$182.46 |
$187.85 |
$196.00 |
$204.04 |
|
3 in Roller Centers |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
|
Between Rail Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4" |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4" |
46-1/4" |
50-1/4" |
54-1/4" |
58-1/4" |
64-1/4" |
70-1/4" |
|
Overall Frame Width |
25-1/2" |
27-1/2" |
29-1/2" |
31-1/2" |
33-1/2" |
37-1/2" |
39-1/2" |
43-1/2" |
45-1/2" |
49-1/2" |
53-1/2" |
57-1/2" |
61-1/2" |
67-1/2" |
73-1/2" |
3" Centers 10' Length-
OA Per Foot |
No. 60 Chain |
$5,536 |
$5,592 |
$5,648 |
$5,704 |
$5,758 |
$5,871 |
$5,926 |
$6,038 |
$6,092 |
$6,205 |
$6,316 |
$6,427 |
$6,538 |
$6,706 |
$6,873 |
|
$389.61 |
$392.85 |
$396.08 |
$399.32 |
$402.44 |
$408.91 |
$412.15 |
$418.62 |
$421.74 |
$428.21 |
$434.68 |
$441.04 |
$447.51 |
$457.22 |
$466.81 |
|
3 3/4 in Roller Centers |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
|
Between Rail Width |
22" |
24" |
26" |
28" |
30" |
34" |
36" |
40" |
42" |
46" |
50" |
54" |
58" |
64" |
70" |
|
Overall Frame Width |
25-1/4" |
27-1/4" |
29-1/4" |
31-1/4" |
33-1/4" |
37-1/4" |
39-1/4" |
43-1/4" |
45-1/4" |
49-1/4" |
53-1/4" |
57-1/4" |
61-1/4" |
67-1/4" |
73-1/4" |
3 3/4" Centers 10' Length-
OA Per Foot |
No. 60 Chain |
$4,292 |
$4,348 |
$4,406 |
$4,464 |
$4,521 |
$4,635 |
$4,692 |
$4,807 |
$4,865 |
$4,979 |
$5,093 |
$5,208 |
$5,323 |
$5,494 |
$5,666 |
|
$286.03 |
$291.19 |
$296.46 |
$301.86 |
$307.13 |
$317.68 |
$322.96 |
$333.63 |
$338.90 |
$349.33 |
$359.88 |
$370.55 |
$381.10 |
$397.04 |
$412.75 |
|
| *No.
40 Chain reduces total conveyor capacity. |
| IMPORTANT
NOTES |
|
• OTHER
LENGTHS
For longer or shorter than 10’ Overall Length,
add or deduct PER FOOT from 10’ price. NO DEDUCT for unit
less than 5’.
• CHAIN GUARD END CAPS
Add 1-3/8" to OAL for Chain Guard End
Caps on 4" centers only. Add 3" to OAL For Chain Guard
End Caps
on 3" roller centers only.
• OTHER WIDTHS
For “IN-BETWEEN WIDTHS”, use
next width plus 10%. For widths up to 74-1/4” OAW, interpolate
plus 10%.
For widths over 74-1/4” OAW, contact us for lead
time.
• INTERMEDIATE BEDS
Use per foot price of width x required length, supports
not included.
• FLOOR SUPPORTS
Floor Supports are not included in base price. There
are two (2) stationary floor supports required for the first
bed section and one (1) support required per bed section
thereafter.
• NON-STANDARD WIDTHS
Contact us for lead time.
|
|
| PRICES
FOR OPTIONAL EQUIPMENT |
|
MOTORS
|
Extra
Motor Price for OTHER THAN: 1 HP-208/230/460/575 V-3 Ph.-60 Hz.-Totally
Enclosed. Speed affects
horsepower requirements. |
|
H.P.
REQ. |
TOTALLY ENCLOSED |
ENERGY EFFICIENT |
200/208/230/460/575 V
3 Ph.-60 Hz. |
115/230 V
1 Ph.-60 Hz. |
230/460 V
3Ph.-60 Hz. |
575 V
3Ph.-60 Hz. |
| 1 |
N/C |
$47.71 |
$264.34 |
$264.34 |
| 2 |
$251.87 |
$652.03 |
$534.90 |
$534.90 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FLOOR
SUPPORTS |
|
|
DRIVE
COMPONENT DEDUCTS |
Not
Included in Base Price. Use Chart Below for
Required Elevation. |
|
|
Less
Complete Motor Drive and Drive Shell (For |
|
|
Slave
Driving) ........... Deduct.................... |
$643.30 |
|
|
|
|
|
|
Less
Motor Only (1 HP-208/230/460/575 V-3 |
|
"HS" SUPPORT |
|
Model No. |
Adjustment to Top of Roller |
Price each |
|
**HSN-1 |
10-1/2" to 12" |
$53.23 |
|
**HSN-2 |
12" to 15" |
$53.59 |
|
**HSN-3 |
15" to 18" |
$55.38 |
|
*HSN-4 |
18" to 21" |
$57.06 |
|
*HSN-5 |
21" to 24" |
$59.10 |
|
*HSN-6 |
24" to 30" |
$72.53 |
|
*HSN-7 |
30" to 36" |
$79.72 |
|
*HSN-8 |
36" to 48" |
$92.19 |
|
*HSN-9 |
48" to 60" |
$103.22 |
|
*HSN-10 |
60" to 72" |
$112.81 |
|
*HSN-11 |
72" to 84" |
$119.76 |
|
*HSN-12 |
84" to 96" |
$133.91 |
|
|
|
|
|
|
|
Ph.-60
Hz.) ............... Deduct .................. |
$161.40 |
|
|
|
Less
Reducer* (4A or 4AC) Deduct ........ |
$175.30 |
|
|
*Less
V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less
chain guard and sprockets when C-Face drive is
supplied. |
|
|
|
|
|
|
|
|
|
|
|
|
|
GUARD
RAILS |
|
|
|
Angle
Type “A”
2” x 1-5/8” x 1/4”
Side Opposite Chain Guard ... per foot ......... |
|
|
|
|
|
$5.87 |
|
|
|
|
|
|
|
|
|
|
|
|
|
CONSTANT
AND VARIABLE SPEEDS |
|
|
|
Constant
C-Face–Within 13-100 FPM .No Charge
Constant V-Belt–Within 4-12 FPM .....................
............................... Use V-Belt Drive Add-on |
|
|
|
|
|
|
|
|
|
|
|
| *
Knee Braces (Included in support price) |
|
|
|
|
|
|
|
|
|
|
|
|
OPTIONAL
FRAME |
|
| Extra
Braces ......Add per pair ................... |
$40.16 |
|
|
|
|
|
5”
x 1-5/8” x 4 Ga. Formed Channel Set Low ..... |
|
**Less
than 18-1/2” top of roller elevation–
Top Side Mounted Drive Required. |
|
|
|
|
...............................
add on per foot ........ |
$3.12 |
|
4”
x 5.4 lbs. Structural Channel ........................ |
|
|
|
|
|
|
|
| OPTIONAL
DRIVE |
|
|
...............................
add on per foot ........ |
$4.80 |
Drive
Type |
Overall Frame Width |
22-1/4" to
34-1/4" |
36-1/4"
to 54-1/4"
|
58-1/4"
to 70-1/4"
|
Top Side
Mounted C-Face |
$295.26 |
$355.56 |
$415.86 |
Top Side
Mounted V-Belt |
$435.88 |
$496.18 |
$556.48 |
|
|
|
|
5”
x 6.7 lbs. Structural Channel Set Low ............. |
|
|
...............................
add on per foot ........ |
$9.71 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HEAVY
DUTY END STOP (SET HIGH ONLY) |
|
|
6”
x 8.2 lbs. structural channel |
|
|
|
19”
- 43” BR ............................................ |
$57.18 |
|
|
|
45”
- 67” BR ............................................ |
$83.44 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
HEAVY
DUTY END STOP (SET LOW ONLY) |
|
| #50
O-Ring Drive Chain ......... Add ......... |
$162.32 |
|
|
|
7”
x 9.8 lbs. structural channel |
| #60
O-ring Drive Chain ......... Add ......... |
$231.85 |
|
|
|
|
19”
- 43” BR ............................................ |
$83.56 |
|
|
|
|
|
|
|
| Under
5’ -0” OAL use Top Side Mounted or V-Belt Drive. |
|
|
|
|
|
45”
- 67” BR ............................................ |
$126.95 |
| V-Belt
Drive. 3'-0" and under use V-Belt Drive ONLY. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ELECTRICAL
CONTROLS |
|
|
|
|
|
|
|
|
|
|
| See
below. |
|
|
CHAIN
CROSSOVER |
|
|
|
|
|
|
|
|
|
|
|
Off-Set
Style “C” or “D” .......................... |
$579.74 |
| GALVANIZING |
|
|
|
|
|
 |
|
Add
to Base Price ........................................ 40%
All Parts to be Galvanized Construction, except
pulleys (Hot Rolled Steel Painted), Drive Shafts,
Tail Shafts, and Idler Shafts will be Cold Rolled
Steel Construction.
Note: Not Rated for Wash Down Application
Note: Contact us for Wash Down Duty
Note: Contact us for Stainless Steel Options |
|
|
|
|
|
|
|
|
|
|
| OPTIONAL
ROLLERS |
|
|
|
|
Use
the following Add-on prices for optional
roller centers and bearings. |
|
|
|
|
| Regreasable
Bearings with Grease Fittings |
|
|
|
|
| 3”
Roller Centers ......... Add-on per foot ... |
$74.93 |
|
|
|
|
| 3-3/4”
Roller Centers ... Add-on per foot ... |
$59.94 |
|
|
|
|
| 4”
Roller Centers ......... Add-on per foot .... |
$56.10 |
|
|
|
|
| 5”
Roller Centers ......... Add-on per foot .... |
$44.96 |
|
|
|
|
| 6”
Roller Centers ......... Add-on per foot .... |
$37.40 |
|
|
|
|
|
|
|
|
|
|
ANGLE
END STOP |
| 7-1/2”
Roller Centers ... Add-on per foot ... |
$29.97 |
|
|
2”
x 2” x 4 Ga. |
|
|
|
|
|
|
|
|
19”
- 23” BR ........................................... |
|
|
|
|
$34.53 |
|
|
|
25”
- 39” BR ............................................ |
$55.62 |
|
|
|
43”
- 67” BR ............................................ |
$68.93 |
|
|
|
|
|
|
|
|
2-1/2" x 7 Ga. with 013.1059 Heavy Duty Bearings |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
| 3"
Centers Add on Per Foot |
$183.30 |
$185.21 |
$187.37 |
$189.53 |
$192.05 |
$196.00 |
$198.16 |
$202.48 |
$204.99 |
$211.47 |
$215.78 |
$209.91 |
$224.42 |
$231.01 |
$237.48 |
| 3-3/4"
Centers Add on Per Foot |
$146.73 |
$148.17 |
$149.85 |
$151.65 |
$153.57 |
$156.80 |
$158.48 |
$161.96 |
$164.00 |
$169.15 |
$172.63 |
$176.10 |
$179.58 |
$184.85 |
$190.01 |
| 4"
Centers Add on Per Foot |
$137.50 |
$138.94 |
$140.50 |
$142.18 |
$143.98 |
$146.97 |
$148.65 |
$151.89 |
$153.69 |
$158.60 |
$161.84 |
$165.07 |
$168.31 |
$173.23 |
$178.14 |
| 5"
Centers Add on Per Foot |
$110.05 |
$111.13 |
$112.45 |
$114.37 |
$115.20 |
$117.60 |
$118.92 |
$121.56 |
$123.00 |
$126.95 |
$129.47 |
$132.11 |
$134.75 |
$138.58 |
$142.42 |
| 6"
Centers Add on Per Foot |
$91.71 |
$92.55 |
$93.63 |
$94.71 |
$96.02 |
$98.06 |
$99.14 |
$101.30 |
$102.50 |
$105.73 |
$107.89 |
$110.05 |
$112.21 |
$115.44 |
$118.68 |
| 7-1/2"
Centers Add on Per Foot |
$73.37 |
$74.09 |
$74.93 |
$75.88 |
$76.84 |
$78.40 |
$79.36 |
$81.04 |
$82.00 |
$84.64 |
$86.31 |
$87.99 |
$89.79 |
$92.31 |
$94.94 |
|
|
|
| ELECTRICAL
CONTROLS AND DRIVE SECTION |
|
|
|
MANUAL
START SWITCH or
SAFETY DISCONNECT
|
|
 |
|
|
|
LIMIT
SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER |
 |
|
|
|
|
| #032.1014......................................... |
$117.96 |
|
|
|
|
#033.2032
& #033.2072..................$109.93
Nema 4 |
"START-STOP",
Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase) |
|
|
|
|
|
|
|
|
LIMIT
SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER |
|
 |
|
|
|
|
|
|
|
|
|
#033.2033&
#033.2072...................$160.67
Nema 4 |
|
|
REVERSING
DRUM SWITCH |
|
|
|
|
|
#032.103.......................................... |
$277.28 |
|
|
|
 |
|
|
|
|
|
|
|
|
|
"Fwd-Stop-Rev",
Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase |
|
|
|
|
|
|
|
LIMIT
SWITCH, TIME DELAY-ON,
WITH NYLON ROLLER LEVEL |
|
|
 |
|
|
|
|
REMOTE
CONTROL ROD |
|
|
|
|
|
|
|
|
|
#033.2052
& #033.2072.................$414.31
Nema 4 |
|
Price
per foot of bed length "L"...........$5.27
Use with standard Reversing Drum Switch,
ONLY. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROXIMITY
SWITCH, INDUCTIVE,
(METAL SENSING) |
|
|
 |
 |
FOOT
SWITCH WITH GUARD |
|
|
#032.209.........................................$113.77
115 Volt AC or 24 Volt DC, two wire with
ground, 30mm dia., 10mm range
|
#032.200.............................................$149.85
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
PHOTO
EYE, ON-OFF TYPE |
 |
POWER
CORD AND PLUG (20') |
|
#033.2122......................................$352.68
115 Volt, relay output, light or dark energized, and includes Reflector. |
| Price................................................. |
$59.10 |
|
(Motor
HP and voltage, etc., must be specified
to size power cord and plug. Max. 1-1/2 HP 1
Phase, 2 HP 3 Phase.) |
|
|
DUAL
TIME DELAY MODULE |
|
|
|
|
|
|
#033.2172.......................................$127.55
For #033.2122 Photo Eye (.5 to 10 seconds
On), (.5 to 10 seconds Off) |
|
|
|
|
|
|
|
|
|
"EMERG.
STOP" PULL CORD SWITCH |
|
|
|
|
|
|
|
|
|
|
|
|
MOUNTING
BRACKETS FOR PHOTO
EYE #033.2122 |
|
|
#032.285
with 032.2851 Turnbuckle
...........................................................$383.38
Nema 4 |
|
|
|
|
|
|
|
|
|
|
|
|
B-05165...........................................$65.34 |
|
|
|
|
|
|
"RED"
EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE |
|
|
|
|
 |
AIR
PRESSURE SWITCH |
|
|
#032.281...one
side.................$4.07 per / ft.
both
sides..............$8.51 per / ft. |
|
#094.191........................................$364.08
Nema 4 |
|
|
EMERGENCY
PUSH BUTTON |
|
|
|
|
|
|
|
|
|
#032.284.............................................$115.93
Nema 4 |
|
|
|
|
NOTE:
PRICING LISTED NOT MOUNTED
OR WIRED |
|
|
|
|
|
|
|
|
|
|
|
PHOTO
EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE |
|
|
|
|
|
|
|
|
|
#032.212
(100mm range, 3.94")......$162.68
#032.2125 (200mm range, 7.87")....$162.68
#033.218 (400mm range, 15.74")....$162.68 |
|
|
|
|
|
|
|
|
|
"PHOTO
EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC |
|
|
|
|
|
|
|
|
|
#033.212B
with 032.21122 Cable.....$248.39
#032.21122 (Cable Only)..................$ 39.92 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC
VARIABLE SPEED DRIVE ADD-ON PRICES
|
|
REPLACEMENT
CONTROLLER
|
|
AC VARIABLE SPEED DRIVES (ALL MOTORS
ARE ENERGY EFFICIENT 3 PHASE)
|
|
SINGLE PHASE CONTROLLER INPUT
|
|
H.P. |
ADD ON PRICE
115 VOLT |
ADD ON PRICE
208/230 VOLT |
|
1/2 |
EA-VSC-12-10 |
EA-VSC-12-12 |
|
Price |
$1,015.93 |
$858.49 |
|
1 |
EA-VSC-12-11 |
EA-VSC-12-13 |
|
Price |
$1,187.65 |
$1,051.65 |
|
2 |
N/A |
EA-VSC-12-14 |
|
Price |
~ |
$1,592.49 |
|
THREE PHASE CONTROLLER INPUT
|
|
H.P. |
ADD ON PRICE
208/230 VOLT |
ADD ON PRICE
460 VOLT |
|
1/2 |
EA-VSC-01-15 |
EA-VSC-01-18 |
|
Price |
$975.84 |
$1,119.00 |
|
1 |
EA-VSC-01-16 |
EA-VSC-01-19 |
|
Price |
$1,111.72 |
$1,250.63 |
|
2 |
EA-VSC-01-17 |
EA-VSC-01-20 |
|
Price |
$1,592.49 |
$1,705.48 |
|
|
|
|
AC VARIABLE SPEED CONTROLLER ONLY
|
|
SINGLE PHASE CONTROLLER INPUT
|
|
Motor Size |
115 Volt |
208/230 Volt |
|
1/2 |
VSC-10 |
VSC-12 |
|
Price |
$827.54 |
$659.78 |
|
1 |
VSC-11 |
VSC-13 |
|
Price |
$956.53 |
$771.70 |
|
2 |
N/A |
VSC-14 |
|
Price |
~ |
$995.43 |
|
THREE PHASE CONTROLLER INPUT
|
|
Motor Size |
208/230 Volt |
460 Volt |
|
1/2 |
VSC-15 |
VSC-18 |
|
Price |
$876.75 |
$918.82 |
|
1 |
VSC-16 |
VSC-19 |
|
Price |
$876.75 |
$995.43 |
|
2 |
VSC-17 |
VSC-20 |
|
Price |
$1,097.69 |
$1,148.63 |
|
|
|
|
|
|
REPLACEMENT
INVERTER DUTY
ENERGY EFFICIENT MOTORS
|
|
|
|
|
OPTIONAL:
Mounting and Wiring Add-On . . .
(mounted close to the motor) |
$214.47 |
|
|
|
|
|
|
HP |
Part No. |
Price |
|
1/2 |
032.351 |
$450.11 |
|
1 |
032.353 |
$488.05 |
|
2 |
032.355 |
$579.13 |
|
| Brake
Relay Kit (EA-068A).............................. |
$299.70 |
|
|
|
IMPORTANT
NOTES...
|
|
|
•
NOTE #1: Add on price includes standard motor deduct.
• NOTE #2: 2 HP Add On Price includes 5AC reducer
upgrade.
• NOTE #3: All above motors are 230 / 460 Volt, 3 Phase.
• NOTE #4: All above V/S Drive Kits include NEMA
1 / IP30 Junction Box, Controller and Motor.
• NOTE #5: Good for cycle rates of up to 15 cycles per
minute,
at 1/2 second ramp time, with a
maximum speed of 250 FPM.
• NOTE #6: Drawing No. DG-001146.
• NOTE #7: When AC Variabl Speed Controller is used
with
a Brake Motor, A Brake Relay Kit
(EA-068A) is required. Add an additional
$299.70 for this option.) |
|
|
|
|
|
|
|
NOTES
|
|
|
•
NOTE #1: All above motors are 230/460 Volt,
3 Phase.
• NOTE #2: All above V/S Controllers are mounted
in NEMA 1 / IP30 Junction Box. |
|
|
|
|
ELECTRONIC
CLUTCH BRAKE DRIVE PACKAGE
|
| Part
No. |
Description |
Price |
|
EA-VSC-01-CB |
2 HP Electronic Clutch-Brake Kit |
$2,887.55 |
|
|
|
|
|
OPTIONAL:
Mounting and Wiring Add-on . .
(mounted close to the motor) |
$214.47 |
|
|
|
|
|
|
|
|
NOTES
|
|
KIT
INCLUDES
|
|
|
•
NOTE #1: Good for cycle rates of up to 60 cycles
per minute.
• NOTE #2: 1/10 second Accel and Decel time, with
350 FPM Maximum Speed.
• NOTE #3: 460 Volt Only, Other Voltages, Contact
us.
• NOTE #4: Motor Cooling Blower is 115 Volt,
1 Phase, 60 Hz.
• NOTE #5: Drawing No. EA-VSC-CB.
• NOTE #6: Price Includes 5AC Reducer and #60
Chain
and Sprockets |
|
Part No. |
Description |
|
VSC-01-20 |
AC Variable Speed Controller, 460 Volt, 3 Phase |
|
032.345 |
2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets |
|
|
|
|
|
Part No. |
Description |
|
VSC-01-17 |
AC Variable Speed Controller, 230 Volt, 3 Phase |
|
032.345 |
2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets |
|
|
|
|
|
|
|
 |
|
THIS
STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
|
|
|
|
An International
Electrotechnical Commission (IEC) term that means: “under
short circuit
conditions, the starter shall cause no danger to persons or installation
and shall be
suitable for further use.” The only allowable damage to
the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting
this level of com-
ponent protection provides users with less down time and lower replacement
costs.
|
|
|
|
|
|
|
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
|
|
H.P.
|
MOTOR
DUTY
|
NON-REVERSING
|
REVERSING
|
|
208 VOLT
|
230 VOLT
|
460 VOLT
|
575 VOLT
|
PRICE
|
208 VOLT
|
230 VOLT
|
460 VOLT
|
575 VOLT
|
PRICE
|
|
1/2
|
STANDARD EASY
CLEAN ENERG. EFF.
|
EN-20B40
|
EN-23B25
|
EN-46B16
|
EN-57B10
|
$601.32
|
ER-20B40
|
ER-23B25
|
ER-46B16
|
ER-57B10
|
$769.87
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
|
EN-23B16
|
EN-46B10
|
|
|
ER-23B16
|
ER-46B10
|
|
|
3/4
|
GEARMOTORS
|
EN-20B40
|
EN-23B40
|
EN-46B16
|
EN-57B16
|
ER-20B40
|
ER-23B40
|
ER-46B16
|
ER-57B16
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
1
|
STANDARD EASY CLEAN
ENERG. EFF.
|
EN-20B40
|
EN-23B40
|
EN-46B25
|
EN-57B16
|
ER-20B40
|
ER-23B40
|
ER-46B25
|
ER-57B16
|
|
|
EN-23B40
|
EN-46B16
|
|
|
ER-23B40
|
ER-46B16
|
|
|
|
EN-23B40
|
EN-46B16
|
|
|
ER-23B40
|
ER-46B16
|
|
|
1-1/2
|
GEARMOTORS
|
EN-20C10
|
EN-23B63
|
EN-46B40
|
EN-57B25
|
ER-20C10
|
ER-23B63
|
ER-46B40
|
ER-57B25
|
|
|
EN-23B63
|
EN-46B25
|
|
|
ER-23B63
|
ER-46B25
|
|
|
|
EN-23B63
|
EN-46B25
|
|
|
ER-23B63
|
ER-46B25
|
|
|
2
|
STANDARD EASY CLEAN
ENERG. EFF.
|
EN-20C10
|
EN-23C10
|
EN-46B40
|
EN-57B40
|
ER-20C10
|
ER-23C10
|
ER-46B40
|
ER-57B40
|
|
|
EN-23C10
|
EN-46B40
|
|
|
ER-23C10
|
ER-46B40
|
|
|
|
EN-23B63
|
EN-46B40
|
|
|
ER-23B63
|
ER-46B40
|
|
|
|
|
|
|
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
|
|
H.P.
|
NON-REVERSING
|
REVERSING
|
NON-REVERSING
|
REVERSING
|
|
|
115 VOLT
|
PRICE
|
115 VOLT
|
PRICE
|
230 VOLT
|
PRICE
|
230 VOLT
|
PRICE
|
|
1/2
|
EN-1SC10
|
$541.02
|
ER-1SC10
|
$769.87
|
EN-2SB63
|
$652.38
|
ER-2SB63
|
$847.20
|
|
3/4
|
EN-1SC16
|
$559.60
|
ER-1SC16
|
EN-2SB63
|
ER-2SB63
|
|
1
|
EN-1SC16
|
ER-1SC16
|
EN-2SC10
|
ER-2SC10
|
|
1-1/2
|
EN-1SC20
|
ER-1SC20
|
EN-2SC10
|
ER-2SC10
|
|
2
|
EN-1SC20
|
ER-1SC20
|
EN-2SC10
|
ER-2SC10
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Start-Stop” Push-button Station |
|
|
OPTIONAL
STARTER CONTROLS
|
033.1955
|
$76.13 |
|
|
|
|
|
|
|
|
|
•
Auto Restart Control, 3 Phase, Non-Reversing |
| Remote
mounted, Nema 1 |
|
|
|
|
|
EA-011
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
|
$1,221.22 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Fwd-Rev-Stop” Push-button Station |
|
|
|
|
| 033.1965 |
$110.05 |
|
|
|
|
| Remote
mounted, Nema 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Up-Down-Stop” Push-button Station |
|
|
|
|
| 033.1975 |
$110.05 |
|
|
|
|
| Remote
mounted, Nema 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•
Auto Restart Control, 1 Phase, Non-Reversing |
•
NOTE #1: All starters listed above require 115 Volt
Control Voltage.
• NOTE #2: Above starters are in Nema 3, 4 and 12
Enclosures.
• NOTE #3: The starters included Safety Disconnect,
Overload Relay, and Aux. Contacts as required.
• NOTE #4: IF AN ORDER IS SUPPLIED LESS
MOTOR, AND IS SUPPLYING ANY
ELECTRICAL CONTROLS, THEN MOTOR HP,
VOLTAGE, PHASE, AND FULL LOAD CURRENT
MUST BE STATED ON THE ORDER.
• NOTE #5: PRICING LISTED IS NOT MOUNTED
OR WIRED. |
|
|
|
EA-012
(115 Volt)
EA-017 (230 Volt)
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), Pushbutton Station (033.195),
and (230 V. Only) a Control Circuit
Transformer (As Required).
Note: Above Price does NOT include Photo Eye Mounting Bracket. |
$1,123.88 |
|
|
|
$1,221.22 |
|
|
|
|
|
|
|
|
|
|
|
•
Mounting Brackets for photo eye |
|
|
|
#033.2122
B-05165 |
$65.34 |
|
|
|
|
| •
NOTE #6: Add on |
$107.17 |
for
the above Push Buttons |
|
|
|
|
|
|
|
|
to
be Mounted. |
|
|
|
|
|
|
| •
NOTE #7: Add on |
$214.47 |
for
the above Starters to be |
|
|
|
|
|
Mounted
and Wired. |
|
|
|
|
|
|
| •
NOTE #8: Add on |
$321.28 |
for
the above Starters and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Push
Button Stations to be Mounted and Wired. |
|
|
|
|
| CONVEYOR
WEIGHT CHART |
|
4 in., 5 in., 6 in., 7-1/2 in. Roller Centers |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
|
Between Rail Width |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
43" |
47" |
51" |
55" |
61" |
67" |
|
Overall Frame Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4 |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4 |
46-1/4" |
50-1/4" |
54-1/4" |
58-1/4" |
64-1/4" |
70-1/4" |
|
*4" Centers 10' Length-
O.A. Per Foot
|
No. 40
Chain |
722 |
750 |
778 |
806 |
834 |
890 |
918 |
974 |
1002 |
1058 |
1114 |
1170 |
1226 |
1310 |
1394 |
|
61 |
64 |
67 |
70 |
73 |
79 |
82 |
88 |
91 |
97 |
103 |
109 |
113 |
124 |
133 |
|
5" Centers 10' Length-
O.A. Per Foot
|
No. 50
Chain |
638 |
666 |
694 |
721 |
749 |
804 |
823 |
887 |
915 |
970 |
1026 |
1081 |
1136 |
1219 |
1302 |
|
54 |
57 |
60 |
63 |
66 |
72 |
75 |
81 |
84 |
90 |
96 |
102 |
108 |
117 |
126 |
|
6" Centers 10' Length-
O.A.
Per Foot
|
No. 60
Chain |
582 |
610 |
638 |
666 |
694 |
750 |
778 |
834 |
862 |
918 |
974 |
1030 |
1086 |
1170 |
1254 |
|
49 |
52 |
55 |
58 |
61 |
67 |
70 |
76 |
79 |
85 |
91 |
97 |
103 |
112 |
121 |
|
7-1/2" Centers 10' Length-
O.A. Per Foot
|
No. 60
Chain |
526 |
554 |
582 |
610 |
638 |
694 |
722 |
778 |
806 |
862 |
918 |
974 |
1030 |
1114 |
1198 |
|
46 |
49 |
52 |
55 |
58 |
64 |
67 |
73 |
76 |
82 |
88 |
94 |
100 |
109 |
118 |
|
3 in Roller Centers |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
|
Between Rail Width |
22-1/4" |
24-1/4" |
26-1/4" |
28-1/4" |
30-1/4" |
34-1/4" |
36-1/4" |
40-1/4" |
42-1/4" |
46-1/4" |
50-1/4" |
54-1/4" |
58-1/4" |
64-1/4" |
70-1/4" |
|
Overall Frame Width |
25-1/2" |
27-1/2" |
29-1/2" |
31-1/2" |
33-1/2" |
37-1/2" |
39-1/2" |
43-1/2" |
45-1/2" |
49-1/2" |
53-1/2" |
57-1/2" |
61-1/2" |
67-1/2" |
73-1/2" |
3" Centers 10' Length-
OA Per Foot |
No. 60 Chain |
862 |
890 |
918 |
946 |
974 |
1030 |
1058 |
1114 |
1142 |
1198 |
1254 |
1310 |
1366 |
1450 |
1534 |
|
72 |
75 |
78 |
81 |
84 |
90 |
93 |
99 |
102 |
108 |
114 |
120 |
126 |
135 |
144 |
|
3 3/4 in Roller Centers |
|
Conveying Surface |
15-3/4" |
17-3/4" |
19-3/4" |
21-3/4" |
23-3/4" |
27-3/4" |
29-3/4" |
33-3/4" |
35-3/4" |
39-3/4" |
43-3/4" |
47-3/4" |
51-3/4" |
57-3/4" |
63-3/4" |
|
Between Rail Width |
22" |
24" |
26" |
28" |
30" |
34" |
36" |
40" |
42" |
46" |
50" |
54" |
58" |
64" |
70" |
|
Overall Frame Width |
25-1/4" |
27-1/4" |
29-1/4" |
31-1/4" |
33-1/4" |
37-1/4" |
39-1/4" |
43-1/4" |
45-1/4" |
49-1/4" |
53-1/4" |
57-1/4" |
61-1/4" |
67-1/4" |
73-1/4" |
3 3/4" Centers 10' Length-
OA Per Foot |
No. 60 Chain |
750 |
778 |
806 |
833 |
861 |
916 |
944 |
999 |
1027 |
1083 |
1137 |
1193 |
1249 |
1332 |
1415 |
|
63 |
68 |
71 |
74 |
77 |
83 |
86 |
92 |
95 |
101 |
107 |
113 |
119 |
128 |
137 |
|
| #40
chain reduces total conveyor capacity. Consult us. |
| All
weights are conveyor weights only. Accessories, crating, etc., are
not included. |
| Note:
Add 1-3/8" to OAL for Chain Guard End Caps on 4" centers
only. |
| Note:
Add 3" to OAL for Chain Guard End Caps on 3" roller centers
only. |
|
Chain Driven Live Roller
Conveyor, Roll-to-Roll, Chain Driven Live Roller Conveyors, Conveyor,
Live Roller
Conveyors, Powered Live Roller, Conveyors, and Roller Conveyors
from your source for material handling equipment.
|
Back to Product Category
|
