Gilmore-Kramer Company Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication
Home Order Search Quote Info About Us My Account Shopping Cart
    Categories
Back to Product Category

MODEL 199-CRRC

CHAIN DRIVEN LIVE ROLLER
CURVE CONVEYOR

The 199-CRRC is a chain driven live
roller curve that aids in alignment of
packages, cartons, etc., through 30 .,
45 ., 60 . and 90 . curves. Can be used
in conveying oily parts.
11 Bed Widths
Reversible
Tapered Tread Rollers
Can Be Slave-driven from 199-CRR
conveyors
Adjustable MS-Type Floor Supports
  Available

chain curve conveyor roller curve conveyor live roller curve convyors
chain driven conveyors

STANDARD SPECIFICATIONS
BED–Roller bed with 2-1/2 in. dia. tapered to
   1-11/16 in. dia. x 16 ga. unplated rollers mounted in
   10 Ga. powder painted formed steel channel frame.
BUTT COUPLINGS–Standard for connecting to
    199-CRR.
SPEED REDUCTION–Sealed worm gear C-Face
    speed reducer.
CENTER DRIVE–Located on 4’-0” long straight
    section.
MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz.
    Totally Enclosed C-Face.
ROLLER CHAIN–No. 40 circular roller-to-roller
   chain.
CONVEYING SPEED–Constant 35 FPM.
MOTOR DRIVE CHAIN–No. 60 chain.
CAPACITY–850 lbs. total distributed live load.
CHAIN GUARD–Mounted to top of channel frame to
    totally enclose drive chain.
FLOOR SUPPORTS–Now supplied as optional
    equipment.
BEARINGS–Sealed, pre-lubricated ball bearings.

OPTIONAL EQUIPMENT SPECIFICATIONS
FLOOR SUPPORTS–MSN Type floor supports are
    available with a wide range of adjustment. Specify top
    of belt or roller elevation. One support required at
    every bed joint and ends of conveyor. Holes in feet for
    lagging to floor. Knee braces recommended above
    MSN-6 support.
GUARD RAILS–Adjustable Universal Channel
    Guard Rail (both sides), fixed channel (both sides)
    or angle (one side). See Accessory section
POLY-TIER SUPPORTS–36 in. to 120 in. support
    heights in 6 in. increments. Knee braces supplied.
CEILING HANGERS–5/8 in. dia. x 8 ft. long
    unplated rods fully threaded. Other lengths and
    galvanized rods available.
CONVEYING SPEED–Other constant and variable
    speeds. NOTE: Capacity affected with speed change.
SHAFT MOUNTED DRIVE–Requires shaft mounted
    gearmotor. Minimum elevation top of rollers 6 in.
MOTORS–Energy efficient, single phase, brakemotor,
    other characteristics. 1 HP maximum.
O-RING DRIVE CHAIN–With sealed in lubricant
    (Recommended for applications that do not permit
    regular lubrication).
ELECTRICAL CONTROLS–Non-reversing or
    reversible magnetic starters and push-button stations.
    AC variable frequency drive.
ROLLERS SET LOW–Tread rollers mounted in
    4-3/4 in. x 10 Ga. formed steel channel frame to form
    1 in. high guard rails.

PRICES FOR COMPLETE CONVEYOR INCLUDE:

2-1/2” Dia. Tapered to 1-11/16” Dia. Roller with #40
    Roller-to-Roller Chain

1/2 HP–“C” Face Totally Enclosed Motor (Specify
    Exact Voltage) Mounted on 4’-0” Tangent
35 FPM Conveying Speed
No. 60 Roller Chain on the Drive.
Less Electrical Controls
4-3/4” x 1-1/2” x 10 Ga. Channel on the Chain Guard
    Side and 3-1/2” x 1-1/2” x 10 Ga. Channel on Side
    Opposite
Less Supports
Totally Enclosed Chain Guard
“C” Face Speed Reducer–Sealed Worm Gear

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


Conveying Surface 12 -1/4" 14 -1/4" 16 -1/4" 18 -1/4" 20 -1/4" 22 -1/4" 24 -1/4" 28 -1/4" 30 -1/4" 34 -1/4" 36 -1/4"
Between Rail Width 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39"
Overall Frame Width 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"
90°
60°
45°
30°
IMPORTANT NOTES...
OTHER WIDTHS DRIVE
 

Contact us for lead time.

  Drive must be mounted on a 4 ft. long tangent.
(Specify infeed or discharge.)
FLOOR SUPPORTS
NON-STANDARD WIDTHS WITH STANDARD INSIDE
   RADIUS
  Floor Supports are not included in base
price. There are two (2) stationary floor
supports and one (1) single center leg
required.
  Contact us for lead time.
MOTORS GUARD RAILS
Extra Motor Price for OTHER THAN: 1/2 HP -
208/230/460/575V - 3 pH - 60 Hz. - Totally Enclosed.
90°, 60°, 45°, 30°
Adjustable Universal Channel Guard Rail
Speed affects horsepower requirements. Inside Only ........................................... $99.70


H.P.
REQ.
TOTALLY ENCLOSED ENERGY EFFICIENT
200/208/230/
460/ 575V
3 Ph - 60 Hz.
115/230V
1 Ph - 60 Hz.
230/460V
3 Ph - 60 Hz.
575 V
3 Ph-
60 Hz.
1/2
N/C
1 N/A
2 N/A
Outside Only ......................................... $151.30
Angle Type “A”
1-1/2” x 1-1/2” x 12 Ga. (Opposite Chain Guard)
.............................................................. $67.70
Fixed Channel Guard Rail
3-1/2” x 1-1/2” Fixed Channel - Opposite Chain
Guard and 2-1/2” x 1-1/2” Fixed Channel on Top
TANGENTS
of Chain Guard .......................................... $210.90
Tangents are available in lengths listed below with rollers
mounted on 4” centers.
3-1/2” x 1-1/2” x 12 Ga. (Outside Only)
OAL Tangent 199-CRRC
12”
16”, 18”, 20”, or 24”
28”, 30”, 32”, 36”
40”, 42”, 44”, 48”
.............................................................. $137.40
NOTE: For tangents over 18” long on either end or both
ends, add one additional floor support per end.
FLOOR SUPPORTS ELECTRICAL CONTROLS
Not Included in Base Price. Use Chart Below for
Required Elevation.
See below
GALVANIZING
MS FLOOR SUPPORTS
Model No. Adjustment to Top of Roller Price Each.
MSN-1* 10-3/4" to 12-1/2"
MSN-1.2* 11-3/4" to 13-1/2"
MSN-1.4* 12-3/4" to 14-1/2"
MSN-2* 13-3/4" to 16-3/4"
MSN-3* 16-11/16" to 19-11/16"
MSN-4 19-11/16" to 25-11/16"
MSN-5 23-11/16" to 29-11/16"
MSN-6 27-11/16" to 39-11/16"
MSN-7 37-11/16" to 49-11/16"
MSN-8 49-11/16" to 61-11/16"
MSN-9 61-11/16" to 73-11/16"
MSN-10 73-11/16" to 85-11/16"
MSN-11 83-11/16" to 95-11/16"
MSN-12
95-11/16" to 107-11/16"
Contact us.
DRIVE COMPONENT DEDUCTS
Less Complete Motor Drive and Tangent
Deduct ................................................ $694.20
Less Motor Only (1/2 HP-208/230/460/575 V-3
Ph.-60 Hz.)
Deduct ................................................ $258.30
Less Reducer* ............... Deduct ............ $307.40
*Less V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less
chain guard and sprockets when C-Face drive is
supplied.
CHAIN CROSSOVER
18” - 24” ............................................... $413.10
26” - 30” ............................................... $463.40
34” - 42” ............................................... $513.50
*Less than 17" top of roller elevation -
Shaft Mounted Drive Required
NOTE: MSN-7 to MSN-12: Knee Braces included
in price.
Extra Knee Braces ...............Add per pair .... $30.00
Single Center Leg (MS-6 and below) each ... $60.40
Single Center Leg (MS-7 and below) each ... $75.10

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CEILING HANGERS
Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated
fully threaded rods ......................................................................
ceiling hangers for conveyors $147.90
Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized
fully threaded rods .......................................................................
$176.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long unplated fully
threaded rods................................................................................
$218.40
Ceiling Hanger Brackets with (2) 5/8” dia. x 10’-0” long galvanized fully threaded rods.................................................................................
$359.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long unplated fully threaded rods.................................................................................
$362.60
Ceiling Hanger Brackets with (2) 5/8” dia. x 12’-0” long galvanized fully threaded rods..................................................................................
$419.40
Ceiling Hanger Brackets, Less Rods Only .................................... $93.10
Extra Length Rods:
(2) 8’-0” long x 5/8” dia. unplated fully threaded rods .................. $54.20
(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods ............... $83.40
(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ................ $125.20
(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods ............. $266.30
(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ................ $269.60
(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods ............. $326.50
Hex Coupling Nuts for Rods ......................................................... $4.90
Above noted delivery times determined by delivery time of model ordered.
POLY-TIER SUPPORTS
poly tier supports for conveyors
PRICES FOR COMPLETE
SUPPORT INCLUDE:
IMPORTANT NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.
• Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
   conveyor)
• "U" Brackets
• Single Width Conveyor Only
CAPACITY DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs
(2) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"
(3) TIER POLY-TIER SUPPORTS
36"
42"
48"
54"
60"
66"
72"
78"
84"
90"
96"
102"
108"
114"
120"

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


ELECTRICAL CONTROLS AND DRIVE SECTION
MANUAL START SWITCH or
SAFETY DISCONNECT
limit switch LIMIT SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER
manual start switch
#032.1014......................................... $213.01 #033.2032 & #033.2072..................$555.67
Nema 4
"START-STOP", Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase)
LIMIT SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER
limit switch double pole

#033.2033& #033.2072...................$332.11
Nema 4
REVERSING DRUM SWITCH
#032.103.......................................... $854.26

"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase
PROXIMITY SWITCH, INDUCTIVE,
(METAL SENSING)

#032.210.........................................$205.35
115 Volt AC, two wire with ground, 30mm dia.,
10mm range


foot swtich with guard FOOT SWITCH WITH GUARD
#032.211.........................................$243.09
24 Volt DC, two wire with ground, 30mm dia.,
10mm range
#032.200........................................... $270.29
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase.


PHOTO EYE, ON-OFF TYPE
power cord and plug #EA-000005......................................$1,059.27
Banner Q45 Retro Reflective Photo Eye Kit
with timing module, reflector and mounting
brackets. Photo Eye output is one form C
type relay, Operating voltage
24-250VAC/12-250VDC
POWER CORD AND PLUG (20')
POWER CORD WITH PLUG ONLY 20' LONG
Model No.
Voltage
HP Rating
Prices
EA-039-1A
115/1
1/2-3/4
EA-039-2A
115/1
1
EA-039-3A
115/1
1 1/2
EA-039-4A
230/1
1/2-1
EA-039-5A
230/1
1 1/2-2
EA-039-6A
208-230/3
1/2-2
EA-039-7A
460/3
1/2-2
POWER CORD WITH PLUG 20' LONG WITH MANUAL START SWITCH AND MOUNTING BRACKET
Model No.
Voltage
HP Rating
Prices
EA-039-1B
115/1
1/2-3/4
EA-039-2B
115/1
1
EA-039-3B
115/1
1 1/2
EA-039-4B
230/1
1/2-1
EA-039-5B
230/1
1 1/2-2
EA-039-6B
208-230/3
1/2-2
EA-039-7B
460/3
1/2-2
MOUNTING BRACKETS FOR PHOTO
EYE #033.2122
B-05165...........................................$118.10

AIR PRESSURE SWITCH
#094.191........................................$691.31
Nema 4

EMERG. STOP PULL CORD SWITCH
#032.285 with 032.2851 Turnbuckle
...........................................................
$696.08
Nema 4
"RED" EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE
#032.281...one side.................$7.44 per / ft.
                  both sides..............$15.87per / ft.
EMERGENCY PUSH BUTTON
#032.284..........................................$279.61
Nema 4

PHOTO EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE
#032.2113 (100mm range, 3.94")....$1,066.27
#032.2116 (200mm range, 7.87")....$194.14
#033.218 (400mm range, 15.74")....$293.48
NOTE: PRICING LISTED NOT MOUNTED
             OR WIRED
"PHOTO EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC
#033.2128 with 032.21122 Cable.....$239.09
#032.21122 (Cable Only)...................$72.37

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


CONTROLLER PRICES
AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size 115 Volt 208/230 Volt
1/2 VSC-12-10 VSC-12-12
Price $1,491.84 $1,189.37
1 VSC-12-11 VSC-12-13
Price $1,724.27
2 N/A
VSC-12-14
Price ~
THREE PHASE CONTROLLER INPUT
Motor Size 208/230 Volt 460 Volt 575 Volt
1/2
VSC-01-15
VSC-01-18
VSC-12-29
Price
1
VSC-01-16
VSC-01-19
VSC-12-29
Price
2
VSC-01-17
VSC01--20
VSC-12-30
Price
REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS
HP Part No. Price
1/2 032.351 230/460
1 032.353 230/460
2 032.355 230/460
1/2 032.3512 575
1 032.3532 575
2 032.3552 575
IMPORTANT NOTES...
All above motors are 230 / 460 / 575 Volt, 3 Phase.
All above V/S Drive Kits include NEMA 1 / IP30
  Junction Box, Controller and Motor.
Good for cycle rates of up to 15 cycles per minute, at
  1/2 second ramp time, with a maximum speed of 250
  FPM.
Drawing No. DG-001146.
OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)
$675.20
Brake Relay Kit (EA-068A).............................. $542.68 When AC Variable Speed Controller is used with a
   Brake Motor, A Brake Relay Kit (EA-068A) is
   required. Add an additional $542.68 for this option.)

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE
Part No. Description Price
EA-VSC-01-CB 2 HP Electronic Clutch-Brake Kit $5,058.00
OPTIONAL: Mounting and Wiring Add-on .
(mounted close to the motor)
$675.20
KIT INCLUDES
Part No. Description
VSC-01-20 AC Variable Speed Controller, 460 Volt, 3 Phase
032.345 2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets
IMPORTANT NOTES
Good for cycle rates of up to 60 cycles per minute.
1/10 second Accel and Decel time, with 350 FPM
   Maximum Speed.
230 or 460 Volt Only, Other Voltages, Contact us.
Motor Cooling Blower is 115 Volt, 1 Phase, 60 Hz.
Price Includes 5AC Reducer and #60 Chain and
  Sprockets
Part No. Description
VSC-01-17 AC Variable Speed Controller, 230 Volt, 3 Phase
032.345 2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


starter
THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use
.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
MOTOR
DUTY
NON-REVERSING
REVERSING
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
208 VOLT
230 VOLT
460 VOLT
575 VOLT
PRICE
1/2
STANDARD EASY
CLEAN ENERG. EFF.
$1516.60
$2,023.30
 
 
 
 
 
 
 
 
1
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
1-1/2
GEARMOTORS
 
 
 
 
 
 
 
 
2
STANDARD EASY CLEAN
ENERG. EFF.
 
 
 
 
 
 
 
 
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.
NON-REVERSING
REVERSING
NON-REVERSING
REVERSING
 
115 VOLT
PRICE
115 VOLT
PRICE
230 VOLT
PRICE
230 VOLT
PRICE
1/2
$1,182.40
$2,023.30
$1,435.60
$2,023.30
1
1-1/2
2
• Manual Start-Stop Switch Kit • Start-Stop Push Button Kit, Remote Mounted
EA-000001 ...................................... $242.09 EA-000002....................................... $242.09
Includes: 032.1014 Manual Start Switch, Nema 1,
B-21467 Mounting Bracket with Mounting Hardware
Includes: 033.1955 Push Button Station, One
Direction, Nema1, B-21467 Mounting Bracket
with Mounting Hardware
Forward-Reverse-Stop Push Button Kit,
  Remote Mounted
• Up-Down-Stop Push Button Kit, Remote
   Mounted
EA-000003....................................... $440.67
Includes: 033.1965 Push Button Station, Reversing,
Nema1, B-21467 Mounting Bracket with Mounting
Hardware
EA-000004....................................... $440.67
Includes: 033.1975 Up Down Stop Push Button
Station, Reversing, Nema 1, B-21467 Mounting
Bracket with Mounting Hardware

Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click a Price of the item you wish to purchase.


• “Start-Stop” Push-button Station • “Start-Stop”Push-button Station
033.1955
$211.23 033.195................................................. $142.50
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Fwd-Rev-Stop” Push-button Station • “Fwd-Rev-Stop”Push Button Station
033.1965 $397.05 033.196.................................................. $490.95
Remote mounted, Nema 1 To be mounted in Mag Starter Cover
• “Up-Down-Stop” Push-button Station
OPTIONAL STARTER CONTROLS
033.1975 $397.05
• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1
EA-011 ............................................
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
$3,210.68
IMPORTANT NOTES
Control Circuit Transformer Included for 115 Volt
  Control Voltage.
Above starters are in Nema 3, 4 and 12 Enclosures.
The starters included Safety Disconnect, Overload
  Relay, and Aux. Contacts as required.
IF AN ORDER IS SUPPLIED LESS MOTOR,
  AND IS SUPPLYING ANY ELECTRICAL
  CONTROLS, THEN MOTOR HP, VOLTAGE,
  PHASE, AND FULL LOAD CURRENT MUST BE
  STATED ON THE ORDER.
PRICING LISTED IS NOT MOUNTED OR WIRED.
• Auto Restart Control, 1 Phase, Non-Reversing
EA-012 (115 Volt) ...........................
EA-017 (230 Volt) ...........................
Includes: Photo Eye (033.2122), Dual
Time Delay Module (033.2172),
Combination Magnetic Starter with extra
Contactor (033.160), Pushbutton Station
(033.195), and (230 V. Only) a Control
Circuit Transformer (As Required).
Note: Above Price does NOT include
Photo Eye Mounting Bracket.
$3,253.63
$3,391.27
Add on $192.70 for the above Push Buttons
  to be Mounted.
Add on $995.10 for the above Starters and
  Push Button Stations to be Mounted and Wired.
  Supply 20'0" of cable for push button only.
• Mounting Brackets for photo eye
#033.2122
B-05165 ..............................................
$118.10

CONVEYOR WEIGHT CHART
Conveying
Surface
Between
Rail Width
Overall
Frame
Width
"R" Number of Rollers* WEIGHTS (Lbs.)
90° 60° 45° 30° 90° 60° 45° 30°
12 1/4" 15" 18" 32 1/2" 14T 10T 6T 4T 390 312 297 282
14 1/4" 17" 20" 400 320 305 290
16 1/4" 19" 22" 410 328 313 298
18 1/4" 21" 24" 420 336 321 306
20 1/4" 23" 26" 430 344 329 314
22 1/4" 25" 28" 440 352 337 322
24 1/4" 27" 30" 450 360 345 330
28 1/4" 31" 34" 48" 20T 16T 10T 6T 480 390 375 365
30 1/4" 33" 36" 560 398 383 373
34 1/4" 37" 40" 530 414 399 389
36 1/4" 39" 42" 540 432 407 397
All weights are conveyor weights only. Accessories, crating, etc., are not included.

Chain Drive Live Roller Curve Conveyor, Chain Driven Live Roller Conveyors, Conveyor, Live Roller Conveyors,
Powered Live Roller, Conveyors, and Roller Conveyors from your source for material handling equipment.

Back to Product Category
Home - Order - Search - Quote- Info - About Us - My Account - Shopping Cart