Accumulating Conveyor, Conveyor, Live Roller Conveyor, Roller Conveyors, Conveyors

Material Handling Equipment - 1-800-544-3137 - Service - Installation - Custom Fabrication


Categories

Back to Product Category

MODEL 190-NSP
LIVE ROLLER CONVEYOR

		The Model 190-NSP Live Roller Spool Conveyor is a general transport conveyor with the capabilities of accumulating products with back pressure.
		Quiet operation, versatile design, easy installation and maintenance make the 190-NSP conveyor a valuable component in operations requiring high performance with minimal downtime.

		12 Bed Widths

		Reversible

		Adjustable MS-Type Floor Supports Available
		Adjustable MS-Type Floor Supports Available

		Stock: Items coded in green ship in 24 hrs.



STANDARD SPECIFICATIONS

BED–Roller bed with 1.9 in. dia. roller x 16 ga. galvanized tube spaced every 3 in. Mounted in 9-1/2 in. x 12 Ga. powder painted formed steel channel frame bolted together with splice plates.
	DRIVE GUARD–Underside of drive shaft with spools and drive o-rings guarded full length of conveyor.

	DRIVE O-RING–3/16 in. dia. polyurethane o-ring from drive spool to tread rollers.

CROSS BRACING–Rods with turnbuckles are fastened to underside of bed to provide proper alignment of bed rollers and insure correct product tracking. Supplied on every other section 30 ft. bed lengths and over.

	BEARINGS–Sealed, pre-lubricated, self-aligning, ball bearings with eccentric lock collar on drive shaft. Pre-lubricated ball bearings in tread rollers.

	SPEED REDUCTION–Sealed worm gear C-Face speed reducer. No. 50 roller chain to drive shaft.

FLOOR SUPPORTS–Now supplied as optional equipment.

	MOTOR–1/2 HP–208/230/460/575V–3 Ph. 60 Hz Totally Enclosed C-Face.

DRIVE–Mounted underneath, placed near center of conveyor. NOTE: On Conveyors less than 24 in. OAW motor extends beyond frame.

	CONVEYING SPEED–Constant 65 FPM.

	CAPACITY–Maximum load per powered roller–15 lbs. NOTE: Maximum load capacity will be less for products with soft or irregular bottoms. Total load NOT TO EXCEED capacity in chart.

DRIVE SHAFT–1 in. dia. steel shaft extends full length of conveyor. Chain coupling at bed joints. Chain guard located on left hand side.


DRIVE SPOOLS–2 in. dia. Delrin spool held in place on drive shaft with spool spacers.

1) Powered drive shaft (coupled at bed joints) is bearing
supported on frame.

2) Drive O-ring transmits power to tread rollers from drive
shaft.

3) Drive spool (held in place by spool spacers) and groove in
tread roller keep drive O-ring in position.

4) If back pressure (accumulation) is applied to tread roller,
drive spool will slip on drive shaft, stopping power to
tread roller.

MOTOR SELECTION CHART

FPM	30-44	45-120
HP (MAX)	1	2

If the required horsepower exceeds the maximum horsepower shown in
the chart, more than one drive is required

LOAD CAPACITY CHART @ 65 FPM

HP	OVERALL FRAME WIDTH			OVERALL FRAME WIDTH			OVERALL FRAME WIDTH
	16" to 22"			24" to 30"			34" to 42"
	TOTAL LOAD (Lbs.)			TOTAL LOAD (Lbs.)			TOTAL LOAD (Lbs.)
	UP TO 60'	UP TO 90'	UP TO 120'	UP TO 60'	UP TO 90'	UP TO 120'	UP TO 60'	UP TO 90'	UP TO 120'
1/2	1550	580	–	1340	250	–	1020	–	–
1	*3600	4090	3110	*3600	3770	2680	*3600	3280	2040
2	–	–	*7200	–	–	*7200	–	–	*7200

*Limited to 15 lbs. per driven roller.
NOTE: Capacity in Chart based on 3 in. roller centers with all rollers powered.


OPTIONAL EQUIPMENT

CONVEYING SPEED–Other constant and variable speeds from 30 to 120 FPM. Over 120 FPM timing belt drive recommended. Capacity affected with speed change.	PACKAGE STOPS–Blade, roller or pin stops available, contact us.

	FLOOR SUPPORTS–MS Type floor supports are available with a wide range of adjustment. Specify top of belt or roller elevation. One support required at every bed joint and ends of conveyor. Holes in feet for lagging to floor. Knee braces recommended above MS-6 support.

SIDE MOUNTED DRIVE–with Reducer.

SIDE MOUNTED DRIVE–with Gearmotor.

O-RING DRIVE CHAIN–With sealed in lubricant (Recommended for applications that do not permit regular lubrication).

	POLY-TIER SUPPORTS–36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.

LOW ELEVATION DRIVE–Gearmotor mounted inside of conveyor. Minimum elevation 11-3/4 in.

	CEILING HANGERS–5/8 in. dia. x 8 ft. long unplated rods fully threaded. Other lengths and galvanized rods available.

POSITIVE DRIVE–Spools are keyed to drive shaft in positive drive areas.

	MOTORS–Energy efficient, single phase, other characteristics. 2 HP maximum.

CROSSOVER–Separate section relocates drive shaft from one side of conveyor to the other. Minimum Elevation - 12-3/8 in.

	ELECTRICAL CONTROLS–Non-reversing or reversible magnetic starter and push-button stations. AC variable frequency drive.
ONE DIRECTION O-RING TRANSFER– See Accessories section.
ONE DIRECTION O-RING TRANSFER– See Accessories section.

REVERSING O-RING TRANSFER– See Accessories section.

GUARD RAILS–Adjustable Universal Channel Guard Rail, fixed channel or type A & B angle. NOTE: If product comes in contact with guard rails, product flow will be affected. Fixed channel overlapping, one direction. Fixed channel non-overlapping, reversing.


PRICES FOR COMPLETE CONVEYOR INCLUDE:

1.9” Dia. x 16 Ga. Galvanized Roller (rollers on 3” Centers) in a 9-1/2” x 12 Ga. Channel Frame	Totally Enclosed Chain Guard

	65 FPM Constant Conveying Speed
	65 FPM Constant Conveying Speed
“C” Face Speed Reducer–Sealed Worm Gear
“C” Face Speed Reducer–Sealed Worm Gear	Less Electrical Controls
	Less Electrical Controls
1/2 HP–“C” Face Totally Enclosed Motor (Specify Exact Voltage)	Less Floor Supports

SIZE TO
ORDER
Overall
Length "A"

Between Rail Widths

13"

15"

17"

19"

21"

23"

25"

27"

31"

33"

37"

39"

Overall Frame Widths

16"

18"

20"

22"

24"

26"

28"

30"

34"

36"

40"

42"

5’

$1,534

$1,569

$1,605

$1,643

$1,678

$1,715

$1,752

$1,787

$1,862

$1,898

$1,970

$2,007

10’

$1,985

$2,038

$2,092

$2,145

$2,198

$2,253

$2,306

$2,359

$2,467

$2,520

$2,627

$2,682

15’

$2,438

$2,507

$2,580

$2,647

$2,717

$2,790

$2,860

$2,930

$3,073

$3,143

$3,283

$3,356

20’

$2,889

$2,976

$3,063

$3,150

$3,237

$3,327

$3,414

$3,501

$3,680

$3,766

$3,941

$4,031

25’

$3,342

$3,445

$3,549

$3,653

$3,757

$3,865

$3,969

$4,073

$4,284

$4,389

$4,596

$4,704

30’

$3,793

$3,914

$4,035

$4,156

$4,277

$4,402

$4,523

$4,644

$4,890

$5,011

$5,253

$5,379

35’

$4,245

$4,383

$4,521

$4,658

$4,796

$4,939

$5,077

$5,215

$5,496

$5,634

$5,910

$6,052

40’

$4,697

$4,851

$5,006

$5,161

$5,317

$5,478

$5,632

$5,787

$6,102

$6,256

$6,567

$6,727

45’

$5,148

$5,320

$5,493

$5,665

$5,835

$6,015

$6,186

$6,357

$6,707

$6,880

$7,223

$7,401

50’

$5,601

$5,789

$5,979

$6,167

$6,356

$6,551

$6,741

$6,929

$7,314

$7,502

$7,880

$8,076

55’

$6,052

$6,259

$6,464

$6,670

$6,875

$7,088

$7,294

$7,500

$7,920

$8,126

$8,536

$8,750

60’

$6,505

$6,727

$6,950

$7,172

$7,396

$7,627

$7,848

$8,072

$8,526

$8,748

$9,194

$9,425

65’

$6,956

$7,196

$7,436

$7,674

$7,914

$8,164

$8,403

$8,642

$9,131

$9,371

$9,850

$10,099

70’

$7,409

$7,665

$7,922

$8,178

$8,435

$8,700

$8,958

$9,213

$9,736

$9,993

$10,506

$10,772

75’

$7,860

$8,133

$8,407

$8,681

$8,954

$9,239

$9,513

$9,786

$10,343

$10,616

$11,163

$11,447

80’

$8,313

$8,602

$8,894

$9,184

$9,474

$9,776

$10,067

$10,356

$10,949

$11,238

$11,821

$12,121

85’

$8,764

$9,072

$9,380

$9,687

$9,993

$10,313

$10,620

$10,929

$11,554

$11,862

$12,476

$12,796

90’

$9,217

$9,541

$9,865

$10,189

$10,514

$10,851

$11,175

$11,499

$12,161

$12,485

$13,133

$13,470

95’

$9,668

$10,011

$10,351

$10,692

$11,032

$11,389

$11,729

$12,071

$12,766

$13,108

$13,789

$14,145

100’

$10,121

$10,479

$10,837

$11,194

$11,553

$11,925

$12,283

$12,641

$13,373

$13,730

$14,446

$14,819

Per Foot Price

$90.39

$93.74

$97.22

$100.58

$103.94

$107.54

$110.89

$114.24

$121.20

$124.56

$131.27

$134.87


IMPORTANT NOTES...
OTHER LENGTHS		NON-STANDARD WIDTHS
	Other lengths not listed in price chart are available. For “IN-BETWEEN SIZES”, use next larger Overall Length “A” price. For lengths longer or shorter than those shown in chart, please contact us.		Contact us for lead time.
		FLOOR SUPPORTS
			Floor Supports are not included in base price. There are two (2) stationary floor supports required for the first bed section and one (1) support required per bed section thereafter.
OTHER WIDTHS
	For “IN-BETWEEN WIDTHS”, use next width plus 10%. For widths up to 63” OAW, interpolate plus 10%. For widths over 63” OAW, contact us.	INTERMEDIATE BEDS
			Use per foot price of width x required length, supports not included. From Stockyard, available in 10 ft. lengths only.

PRICES FOR OPTIONAL EQUIPMENT

OPTIONAL DRIVES

FLOOR SUPPORTS

Drive T ype	OVERALL FRAME WIDTH
Drive T ype	20" to 24"	26" to 42"
Low Elevation*	$154.65	$193.24
	16" to 24"	26" to 42"
Side Mounted C-Face	$154.65	$193.24
Side Mounted Timing Belt	$760.64	$799.24
Underside V-Belt	$140.62	$140.62

Not Included in Base Price. Use Chart Below for
Required Elevation.

"MS" SUPPORT

"MS" SUPPORT
Model No.	Adjustment to Top of Roller	Price each
*MSL-1	11-3/4" to 12-3/4"	$33.45
*MSL-2	12-3/4" to 14-1/2"	$33.45
*MSL-3	14-1/2" to 17-1/8"	$33.45
*MS-1	16-3/4" to 18-1/2"	$33.45
*MS-1.2	17-3/4" to 19-1/2"	$33.45
*MS-1.4	18-3/4" to 20-1/2"	$33.45
*MS-2	19-3/4" to 22-3/4"	$34.53
*MS-3	22-3/8" to 25-3/8"	$37.89
MS-4	25-3/8" to 31-3/8"	$43.76
MS-5	29-3/8" to 45-3/8"	$45.55
MS-6	33-3/8" to 45-3/8"	$50.23
MS-7	43-3/8" to 55-3/8"	$57.54
MS-8	55-3/8" to 67-3/8"	$68.21
MS-9	67-3/8" to 79-3/8"	$76.25
MS-10	79-3/8" to 91-3/8"	$89.07
MS-11	89-3/8" to 101-3/8"	$100.34
MS-12	101-3/8" to 113-3/8"	$105.85

* NOTE: 11-1/4” minimum elevation Requires Eurodrive
Gearmotor (See Motor Chart)

POSITIVE DRIVE

........................add on per foot ..................

$16.55

CONSTANT AND VARIABLE SPEEDS

Constant-Within 30 to 120 FPM .............. No Charge

Variable Speed ............. See Electrical Controls and

Drive Section See Below

NOTE:

Stockyard Models Only 65 FPM Constant Speed

TIMING BELT DRIVE

Required with speeds above 120 FPM ....................

............................................Add-on ...........

$610.32

O-RING DRIVE CHAIN

Speeds up to 90 FPM (#50 Chain)........................
..........................................Add-On.................$162.31
Speeds up to 90 FPM (#60 Chain)........................
..........................................Add-On................ $231.84

* Less than 24" top of roller elevation - Low Elevation
Drive Required.

NOTE: MS-7 to MS-12: Knee Braces included in price.

Extra Knee Braces .......Add per pair .........

$16.66

MOTORS

Extra Motor Price for OTHER THAN: 1/2 HP - 208/230/460/575V - 3 Ph - 60 Hz. - Totally Enclosed.

Speed affects horsepower requirements.

H.P. REQ.	TOTALLY ENCLOSED		ENERGY EFFICIENT
H.P. REQ.	200/208/ 230V 3Ph. - 60 Hz.	115/230V 1 Ph. - 60 Hz.	230/460V 3 Ph. - 60 Hz.	575V 3 Ph. - 60 Hz.
1/2	N/C	$22.30	$228.85	$228.85
1	$37.04	$81.76	$284.47	$284.47
2	$298.38	$688.83	$554.93	$554.93

H.P. Req.	Eurodrive Gearmotor (Required with Low Elevation Drive)
H.P. Req.	208/230/ 460/575 3 Ph.-60Hz.
3/4	$810.03
1	$873.45
1-1/2	$963.11

DRIVE COMPONENT DEDUCTS

Less Motor Drive, Motor Mount, Sprockets and

Guards, but with Drive Shaft ...Deduct .....

$478.90

Less Motor Only (1/2 HP-208/230/460/575V-
Ph.-60 Hz.)

........................................Deduct .............

$147.50

Less Reducer ..................Deduct .............

$175.30

(Chain Guard and Sprockets Not Supplied)

GALVANIZING

CROSSOVER

Add to Base Price ............................................ 40%
All Parts to be Galvanized Construction, except
pulleys (Hot Rolled Steel Painted), Drive Shafts,
Tail Shafts, and Idler Shafts will be Cold Rolled
Steel Construction.

Chain

Speeds up to 120 FPM ..........Add-on ......

$476.16

#50 O-Ring Chain

Speeds up to 120 FPM ..........Add-on ......

$663.17

Note: Not Rated for Wash Down Application
Note: Contact us for Wash Down Duty
Note: Contact us for Stainless Steel Options

GUARDS RAILS						PACKAGE STOPS
	NOTE: Available in 5' and 10' lengths only from Stockyard. Contact us for other lengths.						Angle End Stop
							1-1/2" x 1-1/2" x 12 Ga. Steel
							13" to 25" Between Rail Width ...................	$17.51
	Adjustable Universal Channel Guard Rail						13" to 25" Between Rail Width ...................	$17.51
	Adjustable Universal Channel Guard Rail						27" to 39" Between Rail Width ...................	$27.93
	Both Sides ...............per foot .....................			$8.63			27" to 39" Between Rail Width ...................	$27.93

							Raised End Roller Stop
	One Side .................per foot ....................			$4.32			Raised End Roller Stop
	One Side .................per foot ....................			$4.32			2-1/8" Dia. Roller

	Angle Type
	Angle Type						13" to 25" Between Rail Width ................	$44.83
	Types "A" or "B" available (specify)						13" to 25" Between Rail Width ................	$44.83
	Types "A" or "B" available (specify)						27" to 39" Between Rail Width ................	$55.50
	Prices are for both sides						27" to 39" Between Rail Width ................	$55.50

							Hand Operated Stop

	Type "A"
	Type "A"						(Blade or Roller Types, specify)
	1-1/2" x 1-1/2" x 12 Ga. per foot ..............			$4.32			(Blade or Roller Types, specify)
	1-1/2" x 1-1/2" x 12 Ga. per foot ..............			$4.32			13" to 39" Between Rail Width .................	$199.36
							13" to 39" Between Rail Width .................	$199.36

	Type "B" (See Note)
	Type "B" (See Note)						Air Operated Linear Thruster Stop
	1-1/2" x 1-1/2" x 12 Ga. per foot .............			$6.23			Air Operated Linear Thruster Stop
	1-1/2" x 1-1/2" x 12 Ga. per foot .............			$6.23			(Pin, Roller or Blade Types, specify)
							(Pin, Roller or Blade Types, specify)
							13" to 39" Between Rail Width .................	$942.98
	Fixed Channel Type						13" to 39" Between Rail Width .................	$942.98
	Fixed Channel Type						NOTE: Air Package Stops are supplied in NORMALLY DOWN position. Can be supplied in Normally Up position -Specify.
	Prices are for both sides.
	3-1/2" x 1-1/2" x 12 Ga. per foot .............			$12.83
	6-1/2" x 1-1/2" x 12 Ga. per foot .............			$15.47
	6-1/2" x 1-1/2" x 12 Ga. per foot .............			$15.47
	10" x 1-1/2" x 12 Ga. per foot .................			$21.70		ELECTRICAL CONTROLS
		13" x 1-1/2" x 12 Ga. per foot .................			$26.25
		13" x 1-1/2" x 12 Ga. per foot .................			$26.25		(See below)
							(See below)

			NOTE: If product comes in contact with guard rails, product flow will be affected.

OPTIONAL CENTERS

Other than Standard 3". See Chart below.

Between Rail Width

13"

15"

17"

19"

21"

23"

25"

27"

31"

33"

37"

39"

Overall Frame Width

16"

18"

20"

22"

24"

26"

28"

30"

34"

36"

40"

42"

Add On Per Foot of
Conveyor 2" Centers

$35.60

$36.80

$38.00

$39.32

$40.52

$42.08

$43.28

$44.48

$46.99

$48.55

$51.07

$52.27

CEILING HANGERS
	Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long unplated fully threaded rods ......................................................................
		$50.23
	Ceiling Hanger Brackets with (2) 5/8” dia. x 8’-0” long galvanized fully threaded rods .......................................................................
		$57.19
	Ceiling Hanger Brackets, Less Rods Only ....................................	$18.34
	Extra Length Rods:
	(2) 8’-0” long x 5/8” dia. unplated fully threaded rods ..................	$21.46
	(2) 8’-0” long x 5/8” dia. galvanized fully threaded rods ...............	$28.30
	(2) 10’-0” long x 5/8” dia. unplated fully threaded rods ................	$28.30
		$22.54
	(2) 10’-0” long x 5/8” dia. galvanized fully threaded rods .............	$22.54
		$29.73

	(2) 12’-0” long x 5/8” dia. unplated fully threaded rods ................
		$28.30
	(2) 12’-0” long x 5/8” dia. galvanized fully threaded rods .............	$61.74
	Hex Coupling Nuts for Rods .........................................................
		$2.52
		$2.52
	Above noted delivery times determined by delivery time of model ordered.

POLY-TIER SUPPORTS

PRICES FOR COMPLETE
SUPPORT INCLUDE:

IMPORTANT NOTES
• Check for Clearance
• Specify type of conveyor to be used.
• Use in place of LS or MS Supports only.

• Painted Steel Support Legs
• Adjustable Cross pipe Assembly
• Knee Braces (1 set per level of
conveyor)
• "U" Brackets
• Single Width Conveyor Only

CAPACITY DATA:
1500 lbs..............................................per cross pipe
4500 lbs..............................................per set of legs

(2) TIER POLY-TIER SUPPORTS
36"	$112.69
42"	$115.32
48"	$117.96
54"	$120.60
60"	$123.24
66"	$125.87
72"	$128.51
78"	$131.14
84"	$133.67
90"	$136.31
96"	$138.94
102"	$141.58
108"	$144.21
114"	$146.86
120"	$149.49

(3) TIER POLY-TIER SUPPORTS
36"	$135.11
42"	$137.74
48"	$140.38
54"	$143.01
60"	$145.66
66"	$148.29
72"	$150.93
78"	$153.57
84"	$156.08
90"	$158.72
96"	$161.36
102"	$164.00
108"	$166.63
114"	$169.27
120"	$171.90

TRAFFIC COP

The Traffic Cop controls product flow from one conveyor onto
another. It allows products from one line of traffic to flow freely,
without interference from another converging line of traffic. This
eliminates collision of products which may cause damage and
disrupt product flow. Specify model, width and degree.

7 arm widths, aluminum

Available in 30°, 45°, 60°, 90° & 180° applications.

Includes mounting hardware

* 180° application - 10" minimum required between lines

5 lbs. Minimum Package Weight at 65 FPM Required to
Actuate Arm.

190-SPS, SPSS, NSP, NSPC, NSPS & NSPSS

190-ACC, LRS, & LRS

Overall Frame Width	16" to 28"	30" to 42"
Price Each	$1,167.17	$1,246.03

250 lbs. Maximum Accumulated Capacity


TURNING WHEEL

Turning Wheels are used in converging 30° and 45° spur applications. Also used at 90° (right angle) transfers where Traffic Cops, Package Stops and other product flow controlling devices are used. Wheel is mounted on adjustable bracket to insure proper package orientation through transfer. Can be mounted to slider bed channels of powered and gravity conveyors - specify model where applicable.


		6" Dia. Turning Wheel with mounting hardware ............... $68.21
		Mounting Hardware for 6-1/2" Channel Only.

O-RING TRANSFER

PRICES FOR BELT TRANSFER INCLUDES:

4 Urethane Transfer O-Rings

Air Operated Lifting Device

Less Electrical Controls

TRANSFER FLOW	BETWEEN RAIL WIDTH
TRANSFER FLOW	13" to 25"	27" to 39"
STANDARD	$2,067	$2,272
OPPOSITE DIRECTION	$2,886	$3,093
REVERSING	$3,296	$3,504

* NOTE:

10" BR NOT AVAILABLE

NOTE:

Length of Transfer Module Available in 3" & 4" Roller Centers Only. With 4” Roller Centers in Area
of Transfer.

NOTE:

O-Ring Transfer Price Does Not Include Conveyor.

NOTE:

No accumulation in transfer section.

NOTE:

1/4 HP per transfer must be included in conveyor HP requirement.

NOTE:

Reversing Type has 1/2 230/460/575/3 Gearmotor with AC Variable Speed Controller.

ELECTRICAL CONTROLS AND DRIVE SECTION

MANUAL START SWITCH or SAFETY DISCONNECT				LIMIT SWITCH, SINGLE POLE, WITH NYLON ROLLER LEVER
MANUAL START SWITCH or SAFETY DISCONNECT				LIMIT SWITCH, SINGLE POLE, WITH NYLON ROLLER LEVER
#032.1014.........................................	$117.96			#033.2032 & #033.2072..................$109.93 Nema 4
"START-STOP", Nema 1, One direction, 30 AMP, 3 Pole (Single or 3 phase)				#033.2032 & #033.2072..................$109.93 Nema 4
				LIMIT SWITCH, DOUBLE POLE, WITH NYLON ROLLER LEVER


				#033.2033& #033.2072...................$160.67 Nema 4
REVERSING DRUM SWITCH
#032.103..........................................	$277.28


"Fwd-Stop-Rev", Nema 1, for 1-1/2 HP at 115 volts or 2 HP at 230 volts single phase, or 2 HP max. three phase
			LIMIT SWITCH, TIME DELAY-ON, WITH NYLON ROLLER LEVEL

REMOTE CONTROL ROD
REMOTE CONTROL ROD			#033.2052 & #033.2072.................$414.31 Nema 4
Price per foot of bed length "L"...........$5.27 Use with standard Reversing Drum Switch, ONLY.


			PROXIMITY SWITCH, INDUCTIVE, (METAL SENSING)

FOOT SWITCH WITH GUARD
FOOT SWITCH WITH GUARD			#032.209.........................................$113.77 115 Volt AC or 24 Volt DC, two wire with ground, 30mm dia., 10mm range
#032.200.............................................$149.85 (Constant Pressure) "On-Off" type, Nema 1, Pilot Control or 1 HP max. single phase.





			PHOTO EYE, ON-OFF TYPE
POWER CORD AND PLUG (20')			#033.2122......................................$352.68 115 Volt, relay output, light or dark energized, and includes Reflector.
Price.................................................	$59.10
(Motor HP and voltage, etc., must be specified to size power cord and plug. Max. 1-1/2 HP 1 Phase, 2 HP 3 Phase.)
			DUAL TIME DELAY MODULE
			DUAL TIME DELAY MODULE
			#033.2172.......................................$127.55 For #033.2122 Photo Eye (.5 to 10 seconds On), (.5 to 10 seconds Off)


"EMERG. STOP" PULL CORD SWITCH
"EMERG. STOP" PULL CORD SWITCH			MOUNTING BRACKETS FOR PHOTO EYE #033.2122
#032.285 with 032.2851 Turnbuckle ...........................................................$383.38 Nema 4			MOUNTING BRACKETS FOR PHOTO EYE #033.2122
			B-05165...........................................$65.34

"RED" EMERGENCY PULL CORD CABLE AND MOUNTING HARDWARE
"RED" EMERGENCY PULL CORD CABLE AND MOUNTING HARDWARE			AIR PRESSURE SWITCH
#032.281...one side.................$4.07 per / ft. both sides..............$8.51 per / ft.			#094.191........................................$364.08 Nema 4
EMERGENCY PUSH BUTTON
EMERGENCY PUSH BUTTON
#032.284.............................................$115.93 Nema 4
		NOTE: PRICING LISTED NOT MOUNTED OR WIRED
		NOTE: PRICING LISTED NOT MOUNTED OR WIRED

PHOTO EYE, 18MM DIA., DIFFUSED, (PHOTO PROX.) 115 VOLT, LIGHT OPERATE, 2-METER CABLE
#032.212 (100mm range, 3.94")......$162.68 #032.2125 (200mm range, 7.87")....$162.68 #033.218 (400mm range, 15.74")....$162.68
"PHOTO EYE, RETRO-REFLECTIVE, (POLARIZED) 24 VOLT DC
#033.212B with 032.21122 Cable.....$248.39 #032.21122 (Cable Only)..................$ 39.92

AC VARIABLE SPEED DRIVE ADD-ON PRICES

REPLACEMENT CONTROLLER

AC VARIABLE SPEED DRIVES (ALL MOTORS ARE ENERGY EFFICIENT 3 PHASE)
SINGLE PHASE CONTROLLER INPUT
H.P.	ADD ON PRICE 115 VOLT	ADD ON PRICE 208/230 VOLT
1/2	EA-VSC-12-10	EA-VSC-12-12
Price	$1,015.93	$858.49
1	EA-VSC-12-11	EA-VSC-12-13
Price	$1,187.65	$1,051.65
2	N/A	EA-VSC-12-14
Price	~	$1,592.49
THREE PHASE CONTROLLER INPUT
H.P.	ADD ON PRICE 208/230 VOLT	ADD ON PRICE 460 VOLT
1/2	EA-VSC-01-15	EA-VSC-01-18
Price	$975.84	$1,119.00
1	EA-VSC-01-16	EA-VSC-01-19
Price	$1,111.72	$1,250.63
2	EA-VSC-01-17	EA-VSC-01-20
Price	$1,592.49	$1,705.48

AC VARIABLE SPEED CONTROLLER ONLY
SINGLE PHASE CONTROLLER INPUT
Motor Size	115 Volt	208/230 Volt
1/2	VSC-10	VSC-12
Price	$827.54	$659.78
1	VSC-11	VSC-13
Price	$956.53	$771.70
2	N/A	VSC-14
Price	~	$995.43
THREE PHASE CONTROLLER INPUT
Motor Size	208/230 Volt	460 Volt
1/2	VSC-15	VSC-18
Price	$876.75	$918.82
1	VSC-16	VSC-19
Price	$876.75	$995.43
2	VSC-17	VSC-20
Price	$1,097.69	$1,148.63

REPLACEMENT INVERTER DUTY
ENERGY EFFICIENT MOTORS

OPTIONAL: Mounting and Wiring Add-On . . .
(mounted close to the motor)

$214.47

HP	Part No.	Price
1/2	032.351	$450.11
1	032.353	$488.05
2	032.355	$579.13

Brake Relay Kit (EA-068A)..............................

$299.70

IMPORTANT NOTES...

• NOTE #1: Add on price includes standard motor deduct.
• NOTE #2: 2 HP Add On Price includes 5AC reducer
                    upgrade.
• NOTE #3: All above motors are 230 / 460 Volt, 3 Phase.
• NOTE #4: All above V/S Drive Kits include NEMA
                    1 / IP30 Junction Box, Controller and Motor.
• NOTE #5: Good for cycle rates of up to 15 cycles per
                    minute, at 1/2 second ramp time, with a
                    maximum speed of 250 FPM.
• NOTE #6: Drawing No. DG-001146.
• NOTE #7: When AC Variabl Speed Controller is used
                    with a Brake Motor, A Brake Relay Kit
                   (EA-068A) is required. Add an additional
                   $299.70 for this option.)

NOTES

• NOTE #1: All above motors are 230/460 Volt,
3 Phase.
• NOTE #2: All above V/S Controllers are mounted
in NEMA 1 / IP30 Junction Box.

ELECTRONIC CLUTCH BRAKE DRIVE PACKAGE

Part No.	Description	Price
EA-VSC-01-CB	2 HP Electronic Clutch-Brake Kit	$2,887.55

OPTIONAL: Mounting and Wiring Add-on . .
(mounted close to the motor)

$214.47

NOTES

KIT INCLUDES

• NOTE #1: Good for cycle rates of up to 60 cycles
                     per minute.
• NOTE #2: 1/10 second Accel and Decel time, with
                     350 FPM Maximum Speed.
• NOTE #3: 460 Volt Only, Other Voltages, Contact
                    us.
• NOTE #4: Motor Cooling Blower is 115 Volt,
                    1 Phase, 60 Hz.
• NOTE #5: Drawing No. EA-VSC-CB.
• NOTE #6: Price Includes 5AC Reducer and #60
                    Chain and Sprockets

Part No.	Description
VSC-01-20	AC Variable Speed Controller, 460 Volt, 3 Phase
032.345	2 HP 460 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets

Part No.	Description
VSC-01-17	AC Variable Speed Controller, 230 Volt, 3 Phase
032.345	2 HP 230 Volt, 3 Phase, C-Face Motor TEBC (Blower Cooled) With 5AC Reducer and #60 Chain and Sprockets

THIS STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)

An International Electrotechnical Commission (IEC) term that means: “under short circuit
conditions, the starter shall cause no danger to persons or installation and shall be
suitable for further use.” The only allowable damage to the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting this level of com-
ponent protection provides users with less down time and lower replacement costs.

THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	MOTOR DUTY	NON-REVERSING					REVERSING
H.P.	MOTOR DUTY	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE	208 VOLT	230 VOLT	460 VOLT	575 VOLT	PRICE
1/2	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B25	EN-46B16	EN-57B10	$601.32	ER-20B40	ER-23B25	ER-46B16	ER-57B10	$769.87
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
			EN-23B16	EN-46B10				ER-23B16	ER-46B10
3/4	GEARMOTORS	EN-20B40	EN-23B40	EN-46B16	EN-57B16		ER-20B40	ER-23B40	ER-46B16	ER-57B16
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
			EN-23B25	EN-46B16				ER-23B25	ER-46B16
1	STANDARD EASY CLEAN ENERG. EFF.	EN-20B40	EN-23B40	EN-46B25	EN-57B16		ER-20B40	ER-23B40	ER-46B25	ER-57B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
			EN-23B40	EN-46B16				ER-23B40	ER-46B16
1-1/2	GEARMOTORS	EN-20C10	EN-23B63	EN-46B40	EN-57B25		ER-20C10	ER-23B63	ER-46B40	ER-57B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
			EN-23B63	EN-46B25				ER-23B63	ER-46B25
2	STANDARD EASY CLEAN ENERG. EFF.	EN-20C10	EN-23C10	EN-46B40	EN-57B40		ER-20C10	ER-23C10	ER-46B40	ER-57B40
			EN-23C10	EN-46B40				ER-23C10	ER-46B40
			EN-23B63	EN-46B40				ER-23B63	ER-46B40

SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
H.P.	NON-REVERSING		REVERSING		NON-REVERSING		REVERSING
	115 VOLT	PRICE	115 VOLT	PRICE	230 VOLT	PRICE	230 VOLT	PRICE
1/2	EN-1SC10	$541.02	ER-1SC10	$769.87	EN-2SB63	$652.38	ER-2SB63	$847.20
3/4	EN-1SC16	$559.60	ER-1SC16		EN-2SB63		ER-2SB63
1	EN-1SC16		ER-1SC16		EN-2SC10		ER-2SC10
1-1/2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10
2	EN-1SC20		ER-1SC20		EN-2SC10		ER-2SC10


• “Start-Stop” Push-button Station					OPTIONAL STARTER CONTROLS
033.1955				$76.13	OPTIONAL STARTER CONTROLS

					• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1					• Auto Restart Control, 3 Phase, Non-Reversing
Remote mounted, Nema 1						EA-011 Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), and a Control Circuit Transformer (As Required), & Pushbutton Station (033.195).	$1,221.22
							$1,221.22

• “Fwd-Rev-Stop” Push-button Station
033.1965				$110.05
Remote mounted, Nema 1

• “Up-Down-Stop” Push-button Station
033.1975				$110.05
Remote mounted, Nema 1
Remote mounted, Nema 1
					• Auto Restart Control, 1 Phase, Non-Reversing
• NOTE #1: All starters listed above require 115 Volt Control Voltage. • NOTE #2: Above starters are in Nema 3, 4 and 12 Enclosures. • NOTE #3: The starters included Safety Disconnect, Overload Relay, and Aux. Contacts as required. • NOTE #4: IF AN ORDER IS SUPPLIED LESS MOTOR, AND IS SUPPLYING ANY ELECTRICAL CONTROLS, THEN MOTOR HP, VOLTAGE, PHASE, AND FULL LOAD CURRENT MUST BE STATED ON THE ORDER. • NOTE #5: PRICING LISTED IS NOT MOUNTED OR WIRED.						EA-012 (115 Volt) EA-017 (230 Volt) Includes: Photo Eye (033.2122), Dual Time Delay Module (033.2172), Combination Magnetic Starter with extra Contactor (033.160), Pushbutton Station (033.195), and (230 V. Only) a Control Circuit Transformer (As Required). Note: Above Price does NOT include Photo Eye Mounting Bracket.	$1,123.88
							$1,221.22


					• Mounting Brackets for photo eye
						#033.2122 B-05165	$65.34

• NOTE #6: Add on		$107.17	for the above Push Buttons
• NOTE #6: Add on		$107.17	for the above Push Buttons
	to be Mounted.
• NOTE #7: Add on		$214.47	for the above Starters to be
	Mounted and Wired.
• NOTE #8: Add on		$321.28	for the above Starters and

	Push Button Stations to be Mounted and Wired.

CONVEYOR WEIGHT CHART

SIZE TO ORDER Overall Length "A"	Between Rail Width	13"	15"	17"	19"	21"	23"	25"	27"	31"	33"	37"	39"
SIZE TO ORDER Overall Length "A"	Overall Frame Width	16"	18"	20"	22"	24"	26"	28"	30"	34"	36"	40"	42"
5’	WEIGHTS (Lbs.) Weights Based on 3" Roller Centers	229	236	249	259	272	284	293	307	329	341	364	376
10’		371	384	409	426	450	472	488	514	553	576	618	639
15’		513	533	569	594	629	660	684	721	778	811	872	902
20’		655	682	729	761	808	848	880	928	1003	1046	1126	1166
25’		797	830	889	929	987	1036	1076	1135	1228	1281	1380	1429
30’		939	979	1049	1096	1166	1224	1271	1342	1453	1517	1634	1692
35’		1082	1128	1209	1264	1344	1413	1467	1549	1678	1752	1888	1956
40’		1224	1276	1369	1431	1523	1601	1663	1756	1903	1987	2142	2219
45’		1366	1425	1529	1599	1702	1789	1859	1963	2127	2222	2396	2483
50’		1508	1574	1689	1766	1881	1977	2054	2170	2352	2458	2650	2746
55’		1650	1723	1849	1934	2060	2165	2250	2377	2577	2693	2904	3009
60’		1793	1871	2009	2102	2238	2354	2446	2584	2802	2928	3158	3273
65’		1935	2020	2169	2269	2417	2542	2642	2791	3027	3163	3412	3536
70’		2077	2169	2329	2437	2596	2730	2837	2998	3252	3399	3666	3800
75’		2219	2317	2489	2604	2775	2918	3033	3205	3477	3634	3920	4063
80’		2361	2466	2649	2772	2954	3106	3229	3412	3702	3869	4174	4326
85’		2503	2615	2809	2939	3133	3294	3425	3619	3926	4104	4428	4590
90’		2646	2764	2969	3107	3311	3483	3620	3826	4151	4340	4682	4853
95’		2788	2912	3129	3274	3490	3671	3816	4033	4376	4575	4936	5117
100’		2930	3061	3289	3442	3669	3859	4012	4240	4601	4810	5190	5380

Accumulating Conveyor, Live Roller Conveyor, Spool Conveyor, Conveyor, Live Roller Conveyors, Powered
Live Roller, Conveyors, and Roller Conveyors from your source for material handling equipment.

Back to Product Category

Home - Product Index - Order - Search - Quote- Info - About Us - Services