Back to Product Category
|
|
|
|
 |
|
 |
|
|
|
| STANDARD
SPECIFICATIONS |
|
|
|
|
| BELT–
Ultimate 140 BBS - Nitrile. |
|
SNUB
IDLER–Adjustable 2-1/8 in dia. pre-lubricated
ball bearings. |
|
|
BED–Roller
bed with 1.9 in. dia. roller x 16 ga.
galvanized tube spaced every 3 in. and 1.9 in. dia.
pressure roller x 16 Ga. galvanized tube spaced every
6 in. Mounted in 6-1/2 in. x 12 Ga. powder painted
formed steel channel frame bolted together with butt
couplings. |
|
|
|
|
|
RETURN
IDLER–Adjustable 1.9 in dia. Pre-lubricated
ball bearings. |
|
|
|
|
TAKE-UP–Take-ups
in center drive. Provides 16 in.
of belt take-up. |
|
|
|
|
BEARINGS–Sealed,
pre-lubricated, self-aligning, ball
bearings on drive, tail, and take-up pulleys. Pre-lubricated
ball bearings in tread and pressure rollers. |
|
|
CROSS
BRACING–Rods with turnbuckles are
fastened to underside of bed to provide proper alignment
of bed rollers and insure correct product tracking.
Supplied on every other section 30 ft. bed lengths and
over. |
|
|
|
|
|
SPEED
REDUCTION–Sealed worm C-Face gear
reducer. No. 50 roller chain to drive sheave. |
|
|
|
|
MOTOR–1/2
HP–208/230/460/575V–3 PH. 60 Hz.
Totally Enclosed C-Face. |
|
|
CENTER
DRIVE–Can be placed in any section of
conveyor length. |
|
|
|
|
|
CONVEYING
SPEED–Constant 65 FPM. |
|
|
DRIVE
PULLEY–8 in. dia. with 1-3/16 in. dia. shaft
at bearings, machine crowned and fully lagged. |
|
|
|
|
|
CAPACITY–Maximum
load per linear foot of conveyor
200 lbs. NOT TO EXCEED capacity in chart. |
|
|
TAIL
PULLEY–4 in. dia. with 1 in. dia. shaft at
bearings,machine crowned. |
|
|
|
|
|
FLOOR
SUPPORTS–Now supplied as optional
equipment. |
|
|
|
|
|
|
LOAD
CAPACITY CHART @65 FPM
|
|
HP |
OVERALL
FRAME WIDTH |
OVERALL
FRAME WIDTH |
OVERALL
FRAME WIDTH |
| 16"
TO 22" |
24"
TO 30" |
34"
TO 42" |
| TOTAL
LOAD (LBS.) |
TOTAL
LOAD (LBS.) |
TOTAL
LOAD (LBS.) |
|
UP TO 50' |
UP TO 100' |
UP TO 50' |
UP TO 100' |
UP TO 50' |
UP TO 100' |
|
1/2 |
1100 |
200 |
600 |
– |
– |
– |
|
1 |
3300 |
2400 |
2800 |
1600 |
2200 |
– |
|
2 |
7000 |
6000 |
6400 |
5200 |
5800 |
3300 |
|
|
|
OPTIONAL
EQUIPMENT
|
|
|
|
|
FLOOR
SUPPORTS–MS Type . oor supports are
available with a wide range of adjustment. Specify top
of belt or roller elevation. One support required at
every bed joint and ends of conveyor. Holes in feet
for lagging to . oor. Knee braces recommended above
MS-6 support. |
|
GUARD
RAILS–Adjustable Universal channel guard
rail, fixed channel, type A angle elevated to allow for
pop-out tread rollers. Type B angle not available. (See
Accessory section.) NOTE: If product comes in
contact with guard rails, product flow will be
affected. Fixed channel overlapping, one direction.
Fixed channel non-overlapping, reversing. |
|
|
|
CONVEYING
SPEED–Other constant and variable
speeds from 20 to 90 FPM. V-belt drive supplied under
46 FPM (2 HP) and with variable speeds. |
|
|
|
|
ROLLER
CENTERS–Tread rollers spaced every 4 in.,
6 in., or 8 in. (4 in. or 8 in. centers NOT AVAILABLE in
7 ft. 6 in. bed). |
NOTE:
Capacity and accumulation feature
affected with speed change. |
|
|
|
|
POLY-TIER
SUPPORTS–36 in. to 120 in. support
heights in 6 in. increments. Knee braces supplied. |
|
|
|
SIDE
MOUNTED LOW ELEVATION CENTER
DRIVE–Motor reducer unit mounted to side of
conveyor. Minimum low elevation 16 in. |
|
|
|
|
|
|
|
CEILING
HANGERS–5/8 in. dia. x 8 ft. long unplated
rods fully threaded. Other lengths and galvanized rods
available. |
|
|
|
SIDE
MOUNTED END DRIVE–Minimum elevation
12-1/4 in. (underside take-up required). |
|
|
|
|
|
|
|
MOTORS–Energy
efficient, single phase, other
characteristics. 2 HP maximum. |
|
|
|
V-BELT
DRIVE–V-belt supplied between motor and
reducer. |
|
|
|
|
|
|
|
ELECTRICAL
CONTROLS–Non-reversing or
reversible magnetic starters and push–button stations.
AC variable frequency drive. |
O-RING
DRIVE CHAIN–With sealed in lubricant
(Recommended for applications that do not permit
regular lubrication). |
|
|
|
|
|
|
|
|
|
PACKAGE
STOPS–Roller or pin type stops available,
contact us. |
|
|
|
|
|
|
|
| PRICES
FOR COMPLETE CONVEYOR INCLUDE: |
|
|
|
1.9" Dia. x 16 Ga. Galvanized Roller (Rollers on 3"
Centers) in a 6-1/2" x 12 Ga. Channel Frame |
|
1/2 HP-"C" Face Totally Enclosed Motor
(Specify Exact Voltage) |
|
Black Ultimate 140 BBS
Belt |
|
Totally Enclosed Chain
Guard |
|
LessFloor Supports |
|
65 FPM Constant Conveying
Speed |
|
"C" Face Speed
Reducer-Sealed Worm Gear |
|
End Guards |
|
|
Less Electrical Controls |
|
SIZE TO
ORDER
Overall
Length
"A" |
Between
Rail Widths |
|
13" |
15" |
17" |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
|
Overall
Frame Widths
|
|
16" |
18" |
20" |
22" |
24" |
26" |
28" |
30" |
34" |
36" |
40" |
42" |
|
Ultimate
140 BBS Belt Widths
|
|
6" |
8" |
|
10’ |
$3,205 |
$3,280 |
$3,356 |
$3,432 |
$3,508 |
$3,583 |
$3,658 |
$3,735 |
$3,886 |
$3,963 |
$4,112 |
$4,187 |
|
15’ |
$3,685 |
$3,779 |
$3,875 |
$3,970 |
$4,066 |
$4,162 |
$4,256 |
$4,351 |
$4,545 |
$4,641 |
$4,830 |
$4,926 |
|
20’ |
$4,163 |
$4,277 |
$4,392 |
$4,509 |
$4,625 |
$4,741 |
$4,854 |
$4,970 |
$5,202 |
$5,319 |
$5,548 |
$5,665 |
|
25’ |
$4,643 |
$4,776 |
$4,912 |
$5,048 |
$5,184 |
$5,320 |
$5,452 |
$5,589 |
$5,861 |
$5,997 |
$6,266 |
$6,403 |
|
30’ |
$5,122 |
$5,274 |
$5,430 |
$5,587 |
$5,743 |
$5,899 |
$6,050 |
$6,208 |
$6,520 |
$6,677 |
$6,984 |
$7,140 |
|
35’ |
$5,602 |
$5,773 |
$5,949 |
$6,126 |
$6,302 |
$6,478 |
$6,650 |
$6,826 |
$7,179 |
$7,355 |
$7,703 |
$7,879 |
|
40’ |
$6,080 |
$6,270 |
$6,467 |
$6,664 |
$6,861 |
$7,058 |
$7,248 |
$7,443 |
$7,836 |
$8,033 |
$8,421 |
$8,617 |
|
45’ |
$6,560 |
$6,769 |
$6,987 |
$7,203 |
$7,420 |
$7,637 |
$7,846 |
$8,062 |
$8,496 |
$8,711 |
$9,139 |
$9,355 |
|
50’ |
$7,039 |
$7,268 |
$7,505 |
$7,741 |
$7,978 |
$8,216 |
$8,445 |
$8,681 |
$9,154 |
$9,391 |
$9,856 |
$10,093 |
|
55’ |
$7,519 |
$7,767 |
$8,023 |
$8,280 |
$8,536 |
$8,794 |
$9,043 |
$9,299 |
$9,812 |
$10,070 |
$10,574 |
$10,831 |
|
60’ |
$7,997 |
$8,265 |
$8,543 |
$8,819 |
$9,097 |
$9,373 |
$9,641 |
$9,918 |
$10,472 |
$10,748 |
$11,292 |
$11,570 |
|
65’ |
$8,477 |
$8,763 |
$9,060 |
$9,358 |
$9,655 |
$9,951 |
$10,239 |
$10,536 |
$11,129 |
$11,427 |
$12,011 |
$12,308 |
|
70’ |
$8,956 |
$9,262 |
$9,580 |
$9,896 |
$10,214 |
$10,530 |
$10,837 |
$11,153 |
$11,788 |
$12,106 |
$12,729 |
$13,045 |
|
75’ |
$9,436 |
$9,761 |
$10,099 |
$10,436 |
$10,772 |
$11,109 |
$11,435 |
$11,772 |
$12,447 |
$12,784 |
$13,447 |
$13,784 |
|
80’ |
$9,914 |
$10,259 |
$10,616 |
$10,974 |
$11,331 |
$11,689 |
$12,033 |
$12,391 |
$13,106 |
$13,462 |
$14,165 |
$14,523 |
|
85’ |
$10,394 |
$10,758 |
$11,136 |
$11,513 |
$11,890 |
$12,268 |
$12,632 |
$13,010 |
$13,764 |
$14,142 |
$14,883 |
$15,260 |
|
90’ |
$10,873 |
$11,257 |
$11,653 |
$12,052 |
$12,449 |
$12,847 |
$13,230 |
$13,627 |
$1,462 |
$14,820 |
$15,602 |
$15,998 |
|
95’ |
$11,353 |
$11,756 |
$12,173 |
$12,590 |
$13,009 |
$13,425 |
$13,828 |
$14,245 |
$15,081 |
$15,498 |
$16,318 |
$16,737 |
|
100’ |
$11,831 |
$12,254 |
$12,692 |
$13,130 |
$13,567 |
$14,004 |
$14,427 |
$14,864 |
$15,739 |
$16,176 |
$17,037 |
$17,474 |
|
Per Foot Price |
$95.90 |
$99.74 |
$103.70 |
$107.77 |
$111.73 |
$115.81 |
$119.64 |
$123.71 |
$131.75 |
$135.70 |
$143.62 |
$147.69 |
|
|
|
|
|
|
| IMPORTANT
NOTES... |
BED LENGTHS |
|
|
OTHER LENGTHS |
|
Intermediate
bed sections are available in multiples
of 4', 5', 6', 7-1/2', 8' and 10' lengths
only. Minimum
standard units consult us. |
|
| |
Other
lengths not listed in price chart are available. For
"IN-BETWEEN SIZES", use next larger Overall
Length "A" price. SEE BED LENGTHS BELOW |
|
|
INTERMEDIATE BEDS |
|
|
OTHER WIDTHS |
|
| |
Use
per foot price of width x required length, supports
not included. From Stockyard, available in 10
ft.
lengths only. |
|
| |
For
"IN-BETWEEN WIDTHS", use next width plus
10%. For widths over 63" OAW, contact us. |
|
|
NON-STANDARD WIDTHS |
|
|
FLOOR SUPPORTS |
|
| |
Contact
us for lead time. |
|
Floor
Supports are not included in base price.There
are two (2) stationary floor supports required for
the first bed section and one (1) support per bed
section thereafter. |
|
|
| PRICES
FOR OPTIONAL EQUIPMENT |
|
|
MOTORS |
Extra
Motor Price for OTHER THAN: 1/2 HP-208/230/460/575V-3 Ph.-60 Hz.-Totally
Enclosed.
Speed affects horsepower requirements. |
|
|
H.P.
REQ.
|
TOTALLY ENCLOSED
|
ENERGY EFFICIENT
|
200/208/230/
460/575V
3 Ph.-60 Hz. |
115/230V
3 Ph.-60 Hz. |
230/460V
1 Ph.-60 Hz. |
575V
3 Ph.-60 Hz. |
|
1/2 |
N/C |
$22.30 |
$228.85 |
$228.85 |
|
1 |
$37.04 |
$81.76 |
$284.47 |
$284.47 |
|
2 |
$298.38 |
$688.83 |
$554.93 |
$554.93 |
|
|
|
|
|
|
|
|
|
OPTIONAL DRIVES |
|
DRIVE COMPONENT DEDUCTS |
|
Drive
T ype |
OVERALL FRAME WIDTH |
|
16" to 28" |
30" to 42" |
|
Center Drive (V-Belt) |
$140.62 |
$140.62 |
Low Elevation Side Mounted
Center Drive (C-Face) |
$211.83 |
$275.12 |
Low Elevation Side Mounted
Center Drive (V-Belt) |
$352.43 |
$415.81 |
Side Mounted End Drive with
Low Elevation Underside
Take-Up (C-Face) |
$678.64 |
$783.78 |
Side Mounted End Drive with
Low Elevation Underside
Take-Up (V-Belt) |
$819.26 |
$924.39 |
Heavy Duty Center Drive
(C-Face) |
$653.95 |
$871.89 |
Heavy Duty Center Drive
(V-Belt) |
$794.54 |
$1,006.33 |
|
|
|
Less
Motor Drive, Motor Mount and Guards,
but with Shaft Extension Deduct ..................... |
|
|
|
|
$478.90 |
|
|
|
Less
Motor Only (1/2 HP-208/230/460/575V-
3 Ph.-60 Hz.) ....Deduct ............................. |
|
|
|
|
$147.50 |
|
|
|
Less Reducer*
..... Deduct ....................... |
$175.30 |
|
|
|
*Less
V-Belt Guard, Chain Guard, sheaves and
sprockets when V-Belt drive is supplied. Less chain
guard and sprockets when C-Face drive is supplied. |
|
|
|
|
|
|
|
SLAVE CONNECTION KIT |
|
|
|
For Slave
Driving existing curves ................. |
$129.60 |
|
|
|
(Please
Provide Sketch) |
|
|
|
|
|
|
|
|
GALVANIZING
|
|
|
|
|
|
|
|
|
Add
to Base Price ............................................ 40%
|
|
|
|
All
parts to be galvanized construction, except
pulleys (hot rolled steel painted), drive shafts, tail
shafts, and idler shafts will be cold rolled steel
construction. |
|
|
|
|
|
|
#50
O-Ring Drive Chain ...................Add ... $162.31 |
|
|
|
#60
O-Ring Drive Chain ...................Add ... $231.84 |
|
|
|
|
|
|
|
Note:
Not rated for washdown application |
|
CONSTANT AND VARIABLE SPEEDS |
|
|
|
|
Note:
Contact us for washdown duty |
|
Constant
C-Face-Within 17-
134 FPM ........ |
|
|
|
|
|
|
|
Note:
Contact us for stainless steel options |
|
No
Charge |
|
|
|
|
Variable
Speed ................See AC Variable Speed Drives |
|
|
|
GUARD RAILS |
|
PACKAGE STOPS |
|
NOTE:
Available in 5’ and 10’ lengths
only from
Stockyard. Contact us for other lengths. |
|
|
Angle
End Stop |
|
Adjustable
Universal Channel Guard Rail |
|
|
|
|
|
1-1/2"
x 1-1/2" x 12 Ga. Steel |
|
|
|
|
|
|
Both
Sides ................per foot ........................ |
$8.63
|
|
|
|
|
|
13"
to 25" Between Rail Width.................... |
$17.51
|
|
One
Sides................. per foot ........................ |
$4.32
|
|
|
|
|
|
27"
to 39" Between Rail Width................... |
$27.93
|
|
Angle
Type "A" |
|
|
|
|
|
|
|
|
|
|
|
Raised
Roller End Stop |
|
1-1/2"
x 1-1/2" 12 Ga..both sides per foot .... |
$4.32
|
|
|
|
|
|
2-1/8"
Dia. Roller |
|
|
Angle
Type "B" Integral |
|
|
|
|
|
|
13"
to 25" Between Rail Width................... |
$44.83
|
|
1-1/2"
x 1-1/2" 12 Ga. with Pop-Out Roller
Feature........both sides per foot.............. |
|
|
|
|
$6.23
|
|
|
27"
to 39" Between Rail Width.................. |
$55.50
|
|
|
|
|
|
|
|
|
NOTE:
Available with 3” and 4” roller centers only. |
|
|
|
|
|
|
Fixed
Channel Type - Non-Overlapping (Reversing) (Prices are for both
sides) |
|
|
Hand
Operated Stop |
|
|
|
(Blade
or Roller Types, specify) |
|
|
|
|
|
|
|
|
3-1/2"
x 1-1/2" x 12 Ga..........per foot.......... |
$12.83
|
|
|
13"
to 39" Between Rail Width ................. |
$199.36
|
|
6-1/2"
x 1-1/2" x 12 Ga..........per foot.......... |
$15.47
|
|
|
|
|
|
|
|
|
Air
Operated Linear Thruster Stop |
|
|
10"
x 1-1/2" x 12 Ga..........per foot.............. |
$21.70
|
|
|
|
|
|
|
(Pin,
Roller or Blade Type. Specify) |
|
|
13"
x 1-1/2" x 12 Ga..........per foot.............. |
$26.25
|
|
|
|
|
|
|
13”
to 39” Between Rail Width................ |
$942.95
|
|
Fixed
Channel Type - Overlapping (One Direction)
(Prices are both sides) |
|
|
|
|
|
NOTE:
Filter Regulator Unit not supplied as standard.
Air Package Stops are supplied in NORMALLY
DOWN position. Can be supplied in Normally
Up position -Specify. |
|
3-1/2"
x 1-1/2" x 12 Ga..........per foot.......... |
$14.74 |
|
|
|
6-1/2"
x 1-1/2" x 12 Ga..........per foot.......... |
$18.59
|
|
|
|
10"
x 1-1/2" x 12 Ga..........per foot.............. |
$24.70
|
|
|
|
|
|
|
|
|
|
13"
x 1-1/2" x 12 Ga..........per foot.............. |
$29.38
|
|
|
|
|
|
|
|
|
ELECTRICAL CONTROLS |
|
|
|
|
|
|
NOTE:
Angle Type and Fixed Channel Guard
Rails are raised with spacer. |
|
|
|
(See
below) |
|
|
|
|
|
|
|
NOTE:
If product comes in contact with guard rails,
product flow will be affected. |
|
|
|
|
|
|
|
|
|
|
|
|
|
TC-250 TRAFFIC COP |
|
|
 |
|
|
|
|
|
|
|
|
|
138-NSPS
& NSPSS |
|
|
|
|
|
138-ACC,
LRS, & LRSS |
|
|
|
|
|
|
|
|
|
|
|
| Overall Frame
Width |
12" to
15" |
18" to
24" |
| Price Each |
$1,058.90 |
$1,128.55 |
|
|
|
|
|
|
|
|
The
traffic Cop controls product flow from one conveyor
onto another. It allows products from one line of traffic to
flow freely, without interference from another converging
line of traffic. This eliminates collision of products which
may cause damage and disrupt product flow. Specify
model, width and degree. |
|
|
|
|
|
190-NSPS
& NSPSS |
|
|
190-ACC,
LRS, & LRSS, 190-ACZ |
|
|
|
|
Overall
Frame Width |
16" to 28" |
30" to 42" |
|
Price Each |
$1,167.17 |
$1,246.03 |
|
|
7 arm widths, aluminum |
|
|
Available in 30°, 45°,
60°, 90° & 180° applications. |
|
|
|
|
|
Includes
mounting hardware. |
|
|
|
| *
180° application-10" minimum required between lines |
|
|
|
|
5 lbs. Minimum Package
Weight at 65 FPM |
|
|
|
|
250 lbs. Maximum Accumulated
Capacity |
|
|
|
|
OPTIONAL
ROLLER CENTERS |
|
Other
than Standard 3". See Chart Below. |
|
|
Between Rail Width |
13" |
15" |
17" |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
|
Overall Frame Width |
16" |
18" |
20" |
22" |
24" |
26" |
28" |
30" |
34" |
36" |
40" |
42" |
Add Per Foot of Conveyor
2" Centers* |
$29.49 |
$31.77 |
$33.69 |
$35.61 |
$37.40 |
$39.32 |
$41.60 |
$43.39 |
$47.11 |
$49.51 |
$53.22 |
$55.03 |
Deduct Per Foot of Conveyor
4" Centers* |
$11.00 |
$11.80 |
$12.70 |
$13.60 |
$14.50 |
$15.50 |
$16.30 |
$17.30 |
$18.90 |
$19.90 |
$21.70 |
$22.60 |
Deduct Per Foot of Conveyor
6" Centers |
$13.50 |
$14.60 |
$15.70 |
$17.00 |
$18.10 |
$19.40 |
$20.50 |
$21.70 |
$24.00 |
$25.20 |
$27.60 |
$28.70 |
|
| NOTE:
4" Centers Not Available on 7'-6" Long Bed Section. |
|
| ELECTRICAL
CONTROLS AND DRIVE SECTION |
|
|
|
MANUAL
START SWITCH or
SAFETY DISCONNECT
|
|
 |
|
|
|
LIMIT
SWITCH, SINGLE POLE,
WITH NYLON ROLLER LEVER |
 |
|
|
|
|
| #032.1014......................................... |
$117.96 |
|
|
|
|
#033.2032
& #033.2072..................$109.93
Nema 4 |
"START-STOP",
Nema 1, One direction, 30
AMP, 3 Pole (Single or 3 phase) |
|
|
|
|
|
|
|
|
LIMIT
SWITCH, DOUBLE POLE,
WITH NYLON ROLLER LEVER |
|
 |
|
|
|
|
|
|
|
|
|
#033.2033&
#033.2072...................$160.67
Nema 4 |
|
|
REVERSING
DRUM SWITCH |
|
|
|
|
|
#032.103.......................................... |
$277.28 |
|
|
|
 |
|
|
|
|
|
|
|
|
|
"Fwd-Stop-Rev",
Nema 1, for 1-1/2 HP at
115 volts or 2 HP at 230 volts single phase,
or 2 HP max. three phase |
|
|
|
|
|
|
|
LIMIT
SWITCH, TIME DELAY-ON,
WITH NYLON ROLLER LEVEL |
|
|
 |
|
|
|
|
REMOTE
CONTROL ROD |
|
|
|
|
|
|
|
|
|
#033.2052
& #033.2072.................$414.31
Nema 4 |
|
Price
per foot of bed length "L"...........$5.27
Use with standard Reversing Drum Switch,
ONLY. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PROXIMITY
SWITCH, INDUCTIVE,
(METAL SENSING) |
|
|
 |
 |
FOOT
SWITCH WITH GUARD |
|
|
#032.209.........................................$113.77
115 Volt AC or 24 Volt DC, two wire with
ground, 30mm dia., 10mm range
|
#032.200.............................................$149.85
(Constant Pressure) "On-Off" type, Nema 1,
Pilot Control or 1 HP max. single phase. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
PHOTO
EYE, ON-OFF TYPE |
 |
POWER
CORD AND PLUG (20') |
|
#033.2122......................................$352.68
115 Volt, relay output, light or dark energized, and includes Reflector. |
| Price................................................. |
$59.10 |
|
(Motor
HP and voltage, etc., must be specified
to size power cord and plug. Max. 1-1/2 HP 1
Phase, 2 HP 3 Phase.) |
|
|
DUAL
TIME DELAY MODULE |
|
|
|
|
|
|
#033.2172.......................................$127.55
For #033.2122 Photo Eye (.5 to 10 seconds
On), (.5 to 10 seconds Off) |
|
|
|
|
|
|
|
|
|
"EMERG.
STOP" PULL CORD SWITCH |
|
|
|
|
|
|
|
|
|
|
|
|
MOUNTING
BRACKETS FOR PHOTO
EYE #033.2122 |
|
|
#032.285
with 032.2851 Turnbuckle
...........................................................$383.38
Nema 4 |
|
|
|
|
|
|
|
|
|
|
|
|
B-05165...........................................$65.34 |
|
|
|
|
|
|
"RED"
EMERGENCY PULL CORD
CABLE AND MOUNTING HARDWARE |
|
|
|
|
 |
AIR
PRESSURE SWITCH |
|
|
#032.281...one
side.................$4.07 per / ft.
both
sides..............$8.51 per / ft. |
|
#094.191........................................$364.08
Nema 4 |
|
|
EMERGENCY
PUSH BUTTON |
|
|
|
|
|
|
|
|
|
#032.284.............................................$115.93
Nema 4 |
|
|
|
|
NOTE:
PRICING LISTED NOT MOUNTED
OR WIRED |
|
|
|
|
|
|
|
|
|
|
|
PHOTO
EYE, 18MM DIA., DIFFUSED,
(PHOTO PROX.) 115 VOLT, LIGHT
OPERATE, 2-METER CABLE |
|
|
|
|
|
|
|
|
|
#032.212
(100mm range, 3.94")......$162.68
#032.2125 (200mm range, 7.87")....$162.68
#033.218 (400mm range, 15.74")....$162.68 |
|
|
|
|
|
|
|
|
|
"PHOTO
EYE, RETRO-REFLECTIVE,
(POLARIZED) 24 VOLT DC |
|
|
|
|
|
|
|
|
|
#033.212B
with 032.21122 Cable.....$248.39
#032.21122 (Cable Only)..................$ 39.92 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC
VARIABLE SPEED DRIVE ADD-ON PRICES
|
|
REPLACEMENT
CONTROLLER
|
|
AC VARIABLE SPEED DRIVES (ALL MOTORS
ARE ENERGY EFFICIENT 3 PHASE)
|
|
SINGLE PHASE CONTROLLER INPUT
|
|
H.P. |
ADD ON PRICE
115 VOLT |
ADD ON PRICE
208/230 VOLT |
|
1/2 |
EA-VSC-12-10 |
EA-VSC-12-12 |
|
Price |
$1,015.93 |
$858.49 |
|
1 |
EA-VSC-12-11 |
EA-VSC-12-13 |
|
Price |
$1,187.65 |
$1,051.65 |
|
2 |
N/A |
EA-VSC-12-14 |
|
Price |
~ |
$1,592.49 |
|
THREE PHASE CONTROLLER INPUT
|
|
H.P. |
ADD ON PRICE
208/230 VOLT |
ADD ON PRICE
460 VOLT |
|
1/2 |
EA-VSC-01-15 |
EA-VSC-01-18 |
|
Price |
$975.84 |
$1,119.00 |
|
1 |
EA-VSC-01-16 |
EA-VSC-01-19 |
|
Price |
$1,111.72 |
$1,250.63 |
|
2 |
EA-VSC-01-17 |
EA-VSC-01-20 |
|
Price |
$1,592.49 |
$1,705.48 |
|
|
|
|
AC VARIABLE SPEED CONTROLLER ONLY
|
|
SINGLE PHASE CONTROLLER INPUT
|
|
Motor Size |
115 Volt |
208/230 Volt |
|
1/2 |
VSC-10 |
VSC-12 |
|
Price |
$827.54 |
$659.78 |
|
1 |
VSC-11 |
VSC-13 |
|
Price |
$956.53 |
$771.70 |
|
2 |
N/A |
VSC-14 |
|
Price |
~ |
$995.43 |
|
THREE PHASE CONTROLLER INPUT
|
|
Motor Size |
208/230 Volt |
460 Volt |
|
1/2 |
VSC-15 |
VSC-18 |
|
Price |
$876.75 |
$918.82 |
|
1 |
VSC-16 |
VSC-19 |
|
Price |
$876.75 |
$995.43 |
|
2 |
VSC-17 |
VSC-20 |
|
Price |
$1,097.69 |
$1,148.63 |
|
|
|
|
|
|
REPLACEMENT
INVERTER DUTY
ENERGY EFFICIENT MOTORS
|
|
|
|
|
OPTIONAL:
Mounting and Wiring Add-On . . .
(mounted close to the motor) |
$214.47 |
|
|
|
|
|
|
HP |
Part No. |
Price |
|
1/2 |
032.351 |
$450.11 |
|
1 |
032.353 |
$488.05 |
|
2 |
032.355 |
$579.13 |
|
| Brake
Relay Kit (EA-068A).............................. |
$299.70 |
|
|
|
IMPORTANT
NOTES...
|
|
|
•
NOTE #1: Add on price includes standard motor deduct.
• NOTE #2: 2 HP Add On Price includes 5AC reducer
upgrade.
• NOTE #3: All above motors are 230 / 460 Volt, 3 Phase.
• NOTE #4: All above V/S Drive Kits include NEMA
1 / IP30 Junction Box, Controller and Motor.
• NOTE #5: Good for cycle rates of up to 15 cycles per
minute,
at 1/2 second ramp time, with a
maximum speed of 250 FPM.
• NOTE #6: Drawing No. DG-001146.
• NOTE #7: When AC Variabl Speed Controller is used
with
a Brake Motor, A Brake Relay Kit
(EA-068A) is required. Add an additional
$299.70 for this option.) |
|
|
|
|
|
|
|
NOTES
|
|
|
•
NOTE #1: All above motors are 230/460 Volt,
3 Phase.
• NOTE #2: All above V/S Controllers are mounted
in NEMA 1 / IP30 Junction Box. |
|
|
|
|
ELECTRONIC
CLUTCH BRAKE DRIVE PACKAGE
|
| Part
No. |
Description |
Price |
|
EA-VSC-01-CB |
2 HP Electronic Clutch-Brake Kit |
$2,887.55 |
|
|
|
|
|
OPTIONAL:
Mounting and Wiring Add-on . .
(mounted close to the motor) |
$214.47 |
|
|
|
|
|
|
|
|
NOTES
|
|
KIT
INCLUDES
|
|
|
•
NOTE #1: Good for cycle rates of up to 60 cycles
per minute.
• NOTE #2: 1/10 second Accel and Decel time, with
350 FPM Maximum Speed.
• NOTE #3: 460 Volt Only, Other Voltages, Contact
us.
• NOTE #4: Motor Cooling Blower is 115 Volt,
1 Phase, 60 Hz.
• NOTE #5: Drawing No. EA-VSC-CB.
• NOTE #6: Price Includes 5AC Reducer and #60
Chain
and Sprockets |
|
Part No. |
Description |
|
VSC-01-20 |
AC Variable Speed Controller, 460 Volt, 3 Phase |
|
032.345 |
2 HP 460 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets |
|
|
|
|
|
Part No. |
Description |
|
VSC-01-17 |
AC Variable Speed Controller, 230 Volt, 3 Phase |
|
032.345 |
2 HP 230 Volt, 3 Phase, C-Face Motor TEBC
(Blower Cooled) With 5AC Reducer and #60 Chain
and Sprockets |
|
|
|
|
|
|
|
 |
|
THIS
STARTER LISTING MEETS TYPE "2"
COORDINATION (Defined)
|
|
|
|
An International
Electrotechnical Commission (IEC) term that means: “under
short circuit
conditions, the starter shall cause no danger to persons or installation
and shall be
suitable for further use.” The only allowable damage to
the starter is light contact burning
or tack welding, provided the contacts are separable. Starters meeting
this level of com-
ponent protection provides users with less down time and lower replacement
costs.
|
|
|
|
|
|
|
THREE PHASE, IEC COMBINATION MAGNETIC STARTERS
|
|
H.P.
|
MOTOR
DUTY
|
NON-REVERSING
|
REVERSING
|
|
208 VOLT
|
230 VOLT
|
460 VOLT
|
575 VOLT
|
PRICE
|
208 VOLT
|
230 VOLT
|
460 VOLT
|
575 VOLT
|
PRICE
|
|
1/2
|
STANDARD EASY
CLEAN ENERG. EFF.
|
EN-20B40
|
EN-23B25
|
EN-46B16
|
EN-57B10
|
$601.32
|
ER-20B40
|
ER-23B25
|
ER-46B16
|
ER-57B10
|
$769.87
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
|
EN-23B16
|
EN-46B10
|
|
|
ER-23B16
|
ER-46B10
|
|
|
3/4
|
GEARMOTORS
|
EN-20B40
|
EN-23B40
|
EN-46B16
|
EN-57B16
|
ER-20B40
|
ER-23B40
|
ER-46B16
|
ER-57B16
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
|
EN-23B25
|
EN-46B16
|
|
|
ER-23B25
|
ER-46B16
|
|
|
1
|
STANDARD EASY CLEAN
ENERG. EFF.
|
EN-20B40
|
EN-23B40
|
EN-46B25
|
EN-57B16
|
ER-20B40
|
ER-23B40
|
ER-46B25
|
ER-57B16
|
|
|
EN-23B40
|
EN-46B16
|
|
|
ER-23B40
|
ER-46B16
|
|
|
|
EN-23B40
|
EN-46B16
|
|
|
ER-23B40
|
ER-46B16
|
|
|
1-1/2
|
GEARMOTORS
|
EN-20C10
|
EN-23B63
|
EN-46B40
|
EN-57B25
|
ER-20C10
|
ER-23B63
|
ER-46B40
|
ER-57B25
|
|
|
EN-23B63
|
EN-46B25
|
|
|
ER-23B63
|
ER-46B25
|
|
|
|
EN-23B63
|
EN-46B25
|
|
|
ER-23B63
|
ER-46B25
|
|
|
2
|
STANDARD EASY CLEAN
ENERG. EFF.
|
EN-20C10
|
EN-23C10
|
EN-46B40
|
EN-57B40
|
ER-20C10
|
ER-23C10
|
ER-46B40
|
ER-57B40
|
|
|
EN-23C10
|
EN-46B40
|
|
|
ER-23C10
|
ER-46B40
|
|
|
|
EN-23B63
|
EN-46B40
|
|
|
ER-23B63
|
ER-46B40
|
|
|
|
|
|
|
SINGLE PHASE, IEC COMBINATION MAGNETIC STARTERS
|
|
H.P.
|
NON-REVERSING
|
REVERSING
|
NON-REVERSING
|
REVERSING
|
|
|
115 VOLT
|
PRICE
|
115 VOLT
|
PRICE
|
230 VOLT
|
PRICE
|
230 VOLT
|
PRICE
|
|
1/2
|
EN-1SC10
|
$541.02
|
ER-1SC10
|
$769.87
|
EN-2SB63
|
$652.38
|
ER-2SB63
|
$847.20
|
|
3/4
|
EN-1SC16
|
$559.60
|
ER-1SC16
|
EN-2SB63
|
ER-2SB63
|
|
1
|
EN-1SC16
|
ER-1SC16
|
EN-2SC10
|
ER-2SC10
|
|
1-1/2
|
EN-1SC20
|
ER-1SC20
|
EN-2SC10
|
ER-2SC10
|
|
2
|
EN-1SC20
|
ER-1SC20
|
EN-2SC10
|
ER-2SC10
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Start-Stop” Push-button Station |
|
|
OPTIONAL
STARTER CONTROLS
|
033.1955
|
$76.13 |
|
|
|
|
|
|
|
|
|
•
Auto Restart Control, 3 Phase, Non-Reversing |
| Remote
mounted, Nema 1 |
|
|
|
|
|
EA-011
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), and a Control Circuit
Transformer (As Required), & Pushbutton
Station (033.195).
|
$1,221.22 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Fwd-Rev-Stop” Push-button Station |
|
|
|
|
| 033.1965 |
$110.05 |
|
|
|
|
| Remote
mounted, Nema 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| •
“Up-Down-Stop” Push-button Station |
|
|
|
|
| 033.1975 |
$110.05 |
|
|
|
|
| Remote
mounted, Nema 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
•
Auto Restart Control, 1 Phase, Non-Reversing |
•
NOTE #1: All starters listed above require 115 Volt
Control Voltage.
• NOTE #2: Above starters are in Nema 3, 4 and 12
Enclosures.
• NOTE #3: The starters included Safety Disconnect,
Overload Relay, and Aux. Contacts as required.
• NOTE #4: IF AN ORDER IS SUPPLIED LESS
MOTOR, AND IS SUPPLYING ANY
ELECTRICAL CONTROLS, THEN MOTOR HP,
VOLTAGE, PHASE, AND FULL LOAD CURRENT
MUST BE STATED ON THE ORDER.
• NOTE #5: PRICING LISTED IS NOT MOUNTED
OR WIRED. |
|
|
|
EA-012
(115 Volt)
EA-017 (230 Volt)
Includes: Photo Eye (033.2122), Dual Time
Delay Module (033.2172), Combination
Magnetic Starter with extra Contactor
(033.160), Pushbutton Station (033.195),
and (230 V. Only) a Control Circuit
Transformer (As Required).
Note: Above Price does NOT include Photo Eye Mounting Bracket. |
$1,123.88 |
|
|
|
$1,221.22 |
|
|
|
|
|
|
|
|
|
|
|
•
Mounting Brackets for photo eye |
|
|
|
#033.2122
B-05165 |
$65.34 |
|
|
|
|
| •
NOTE #6: Add on |
$107.17 |
for
the above Push Buttons |
|
|
|
|
|
|
|
|
to
be Mounted. |
|
|
|
|
|
|
| •
NOTE #7: Add on |
$214.47 |
for
the above Starters to be |
|
|
|
|
|
Mounted
and Wired. |
|
|
|
|
|
|
| •
NOTE #8: Add on |
$321.28 |
for
the above Starters and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Push
Button Stations to be Mounted and Wired. |
|
|
|
|
| CONVEYOR
WEIGHT TABLE |
SIZE TO ORDER
Overall Length
"A" |
Between
Rail Width |
13" |
15" |
17" |
19" |
21" |
23" |
25" |
27" |
31" |
33" |
37" |
39" |
|
Drive Belt Width |
6" |
6" |
6" |
6" |
6" |
6" |
6" |
6" |
8" |
8" |
8" |
8" |
Overall
Frame Width |
16" |
18" |
20" |
22" |
24" |
26" |
28" |
30" |
34" |
36" |
40" |
42" |
|
10’ |
WEIGHTS
(Lbs.)
Weights
Based on
3" Roller
Centers
|
385 |
416 |
448 |
479 |
509 |
551 |
581 |
612 |
679 |
720 |
771 |
803 |
|
15’ |
521 |
552 |
596 |
637 |
679 |
733 |
774 |
816 |
908 |
950 |
1033 |
1077 |
|
20’ |
657 |
688 |
744 |
797 |
849 |
915 |
967 |
1020 |
1137 |
1190 |
1295 |
1351 |
|
25’ |
793 |
824 |
898 |
956 |
1019 |
1097 |
1160 |
1224 |
1366 |
1430 |
1557 |
1625 |
|
30’ |
929 |
960 |
1040 |
1115 |
1189 |
1279 |
1353 |
1428 |
1595 |
1670 |
1819 |
1899 |
|
35’ |
1065 |
1096 |
1188 |
1274 |
1359 |
1461 |
1546 |
1632 |
1824 |
1910 |
2081 |
2173 |
|
40’ |
1201 |
1232 |
1336 |
1433 |
1529 |
1643 |
1739 |
1836 |
2053 |
2150 |
2343 |
2447 |
|
45’ |
1337 |
1368 |
1484 |
1592 |
1699 |
1825 |
1932 |
2040 |
2282 |
2390 |
2605 |
2721 |
|
50’ |
1473 |
1504 |
1632 |
1751 |
1869 |
2007 |
2125 |
2244 |
2511 |
2630 |
2867 |
2995 |
|
55’ |
1609 |
1640 |
1780 |
1910 |
2039 |
2189 |
2318 |
2448 |
2740 |
2870 |
3129 |
3269 |
|
60’ |
1745 |
1776 |
1928 |
2069 |
2209 |
2371 |
2511 |
2652 |
2969 |
3010 |
3391 |
3543 |
|
65’ |
1886 |
1912 |
2076 |
2228 |
2379 |
2553 |
2704 |
2856 |
3198 |
3350 |
3653 |
3817 |
|
70’ |
2017 |
2048 |
2224 |
2387 |
2549 |
2735 |
2897 |
3060 |
3427 |
3590 |
3915 |
4091 |
|
75’ |
2153 |
2184 |
2372 |
2546 |
2719 |
2917 |
3090 |
3264 |
3656 |
3830 |
4177 |
4365 |
|
80’ |
2289 |
2320 |
2520 |
2705 |
2889 |
3099 |
3283 |
3468 |
3885 |
4070 |
4439 |
4639 |
|
85’ |
2425 |
2456 |
2668 |
2864 |
3059 |
3281 |
3476 |
3672 |
4114 |
4310 |
4701 |
4913 |
|
90’ |
2561 |
2592 |
2816 |
3023 |
3229 |
3463 |
3669 |
3876 |
4343 |
4550 |
4963 |
5187 |
|
95’ |
2697 |
2728 |
2964 |
3182 |
3399 |
3645 |
3862 |
4080 |
4572 |
4790 |
5225 |
5461 |
|
100’ |
2833 |
2864 |
3112 |
3341 |
3569 |
3827 |
4055 |
4284 |
4801 |
5030 |
5487 |
5735 |
|
| All
weights are conveyor weights only. Accessories, crating, etc.
are not included. |
| NOTE:
Bed sections available in multiples of 4 ft., 5 ft., 6 ft., 7-1/2
ft., 8 ft., 9 ft. and 10 ft. lengths only. |
|
Accumulating
Conveyor, Conveyor, Live Roller Conveyors, Powered Live Roller, Power
Conveyor, Conveyors,
and Roller Conveyors from your source for material handling equipment. |
Back to Product Category
|
