Back to Product Category
|
AIR
CURTAINS
|
|
|
|
 |
|
ENERGY |
|
Our air
curtains conserve energy and improve comfort by limiting
the escape of internal heat, reducing cold drafts and providing a
welcoming down flow curtain of warm air at entrance ways in industrial
plants and store buildings. The resulting mixture of warmed air disperses
gently in all directions at floor level to give uniform temperature
over a
wide area from floor to ceiling with only a few degrees difference. |
|
|
|
CONVENIENCE |
|
Our air
curtains allow personnel and cargo to pass freely from one
area to another while maintaining desired temperatures. |
|
An added
safety feature is the free flow of traffic with an unobstructed
view through the opening, eliminating doorway accidents. |
|
|
|
TYPICAL
USES |
|
|
|
Easily mounted
over entrance ways of warehouse doors up to 16 feet
high, the air curtains direct an invisible stream of stratified heated
air
downward. In addition to adding to employee and customer comfort
during cold weather they provide important energy savings in three
ways: |
|
|
|
1. In cold
weather they reduce the load on heating systems. By drawing
warm air down to floor level where it is needed, our air curtains
utilize
the 50% of wasted heated air trapped under ceilings. Stratified air
is
mixed and circulated with building heat and heat given off by lights
and machinery, etc. |
|
|
|
2. The high
velocity curtain of air deflects winds and reduces excessive
heat loss through open doorways. |
|
|
|
3. During
warm weather they can direct a stream of air downward to
help keep dust, dirt, insects and fumes from entering through open
doorways. If air conditioning exists in the building during warm weather,
the air curtains can be used to prevent loss of conditioned air as
well. |
|
|
|
|
|
|
|
|
|
Our
air curtains create an invisible barrier of high
velocity air to stop cold or warm air infiltrating plant
facilities and work areas. |
Stop entry of cold or warm air when doors are
open. |
|
Prevent the possibility of accidents with unobstructed
view of passageways. |
|
|
|
|
IMPORTANT:
MUST BE INSTALLED ON WARM
SIDE OF DOORWAY OPENING WHEN USED FOR
TEMPERATURE CONTROL |
Eliminate need for expensive plastic stripping, flapper
doors, or canvas curtains. |
|
Cold
weather can be further deterred at door opening if
space heater in plant is directed toward intake of the air
curtain. |
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
| SPECIFICATIONS
AND FEATURES |
|
|
|
|
|
|
|
| FOR
ARCHITECTS AND ENGINEERS |
|
EASY
INSTALLATION |
Our
air curtains shall have a self-contained one piece
housing, fire retardant and corrosion proof, in-
corporated with a double extended shaft motor, direct
drive double width and double inlet squirrel cage blower
wheels and fan housings. |
|
Our
air curtains are bolted to wall with four fasteners
and connected to electric power source. |
|
AIR
VELOCITY CONTROL FOR VARIABLE
AIR SPEED |
|
Adjustable
louver damper controls are provided in
order to adjust rate of air flow. |
Shall
have wedge shaped discharge nozzle containing
adjustable air deflectors with 40% sweep front to back. |
|
|
When
used over a doorway to retain warm or cold
temperature, proper velocity adjustment is imperative
for maximum efficiency. Velocity Control can reduce
air velocity up to 60% with louvers in totally closed
position. |
Housing
shall be sufficient strength for fastening to wall
on both ends without any intermediate support. |
|
| HEAVY
DUTY ELECTRIC MOTOR |
|
Continuous
duty type motor with double sealed lifetime
pre-lubricated stainless steel ball bearings, resilient
mounted and protected by an automatic thermal overload
switch. Underwriters Laboratories Listed and Canadian
Standards Association Certified. Explosion proof motors
available. |
|
|
AIR
DIRECTIONAL CONTROL |
|
Adjustable
vanes at outlet nozzle for directing air
to compensate for possible draft conditions through
doorways. |
|
|
|
|
| FIRE
RETARDANT AND CORROSION PROOF |
|
|
How
Air Curtain Works
|
|
Steel
models are of 18 gauge paintlock metal and double
protected with gray, baked, rust preventative electrostatic
polyurethane powder coating. |
|
|
 |
|
| NOISE
LEVEL |
|
|
|
Our
air curtains operate under a low noise level in the
interest and comfort of personnel working in the immediate
vicinity. |
|
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
|
|
|
|
SELECTION
TABLE
|
|
APPLICATIONS |
BARRIER TO
INSECTS, DUST
AND FUMES |
CONTAIN BLDG.
AIR HEATED
OR COOLED |
FREEZERS
-20° TO +25° |
COOLERS
+25° TO +60° |
Door widths
up to (ft) |
Use this model number |
DOOR HEIGHT UP TO (FEET) |
| 3 |
STD 36-1 |
8 |
10 |
10 |
10 |
|
3 1/2 |
STD 42-1 |
8 |
10 |
10 |
10 |
| 4 |
STD 48-1 |
8 |
10 |
10 |
10 |
| 5 |
STD 60-1 |
8 |
10 |
10 |
10 |
|
5 1/3 |
STD 64-2 |
8 |
10 |
10 |
10 |
| 6 |
STD 72-2 |
8 |
10 |
10 |
10 |
|
6 1/2 |
STD 78-2 |
8 |
10 |
10 |
10 |
| 7 |
STD 84-2 |
8 |
10 |
10 |
10 |
| 8 |
STD 96-2 OR STD 96-3 |
8 |
10 |
10 |
10 |
| 10 |
STD 120-3 |
8 |
10 |
10 |
10 |
| 12 |
STD 144-3 or STD 144-4 |
8 |
10 |
10 |
10 |
| 4 |
HV 42-1 |
10 |
12 |
12 |
12 |
|
4 1/2 |
HV 48-1 |
10 |
12 |
12 |
12 |
| 5 |
HV 60-1 |
10 |
12 |
12 |
12 |
| 6 |
HV 72-2 |
10 |
12 |
12 |
12 |
| 7 |
HV 84-2 |
10 |
12 |
12 |
12 |
| 8 |
HV 96-2 OR HV 96-3 |
10 |
12 |
12 |
12 |
| 10 |
HV120-2 OR HV 120-3 |
10 |
12 |
12 |
12 |
| 12 |
HV 144-3 OR HV 144-4 |
10 |
12 |
12 |
12 |
| 14 |
(2) HV 84-2 |
10 |
12 |
12 |
12 |
|
4 1/2 |
EP 48-1 |
14 |
16 |
16 |
16 |
| 5 |
EP 60-1 |
14 |
16 |
16 |
16 |
| 7 |
EP 84-2 |
14 |
16 |
16 |
16 |
| 8 |
EP 96-2 |
14 |
16 |
16 |
16 |
| 10 |
EP 120-2 OR EP 120-3 |
14 |
16 |
16 |
16 |
| 12 |
EP 144-3 |
14 |
16 |
16 |
16 |
| 14 |
(2) EP 84-2 |
14 |
16 |
16 |
16 |
| 16 |
(2) EP 96-2 |
14 |
16 |
16 |
16 |
| 18 |
EP 96-2 & EP 120-3 |
14 |
16 |
16 |
16 |
| 20 |
(2) EP 120-2 |
14 |
16 |
16 |
16 |
| 20 |
(2) EP 120-3 |
14 |
16 |
16 |
16 |
|
|
| Standard
Features: |
|
|
|
|
|
|
|
|
*
All 3 Phase Motor Up
Charges = $75.00 / Motor |
| 1/2
HP Direct Drive |
|
Motor
Fan Assembly |
|
| 14"
Profile Metal Design |
|
Gray
Powder Coating |
|
|
|
|
| Easy
Install |
|
|
|
|
|
|
|
|
|
|
|
|
PRICING
AND SPECIFICATIONS FOR STANDARD - (UNHEATED
MODELS)
|
|
MODELS |
LENGTH |
FPM AT
NOZZLE |
CFM AT
NOZZLE |
MOTORS |
FLA (AMPACITY)
SINGLE PHASE |
FLA (AMPACITY)
THREE PHASE |
SHIP
WT
(LBS) |
PRICE |
|
HP |
RPM |
115V |
208V 230V |
208V 230V |
460V |
|
STANDARD MODELS |
|
STD 36-1U* |
3' |
3400 |
2550 |
1/2 HP |
1750 |
5.1 |
2.5/2.5 |
1.8/1.6 |
0.8 |
55 |
$733 |
|
STD 42-1U* |
3' 6" |
2925 |
2550 |
1/2 HP |
1750 |
5.1 |
2.5/2.5 |
1.8/1.6 |
0.8 |
60 |
$755 |
|
STD 48-1U* |
4' |
2550 |
2550 |
1/2 HP |
1750 |
5.1 |
2.5/2.5 |
1.8/1.6 |
0.8 |
65 |
$777 |
|
STD 64-2U* |
5' 4" |
3020 |
5100 |
2-1/2 HP |
1750 |
10.2 |
5.0/5.0 |
3.6/3.2 |
1.6 |
140 |
$1,177 |
|
STD 72-2U* |
6' |
3475 |
5100 |
2-1/2 HP |
1750 |
10.2 |
5.0/5.0 |
3.6/3.2 |
1.6 |
145 |
$1,254 |
|
STD 78-2U* |
6' 6" |
3200 |
5100 |
2-1/2 HP |
1750 |
10.2 |
5.0/5.0 |
3.6/3.2 |
1.6 |
150 |
$1,332 |
|
STD 84-2U* |
7' |
2925 |
5100 |
2-1/2 HP |
1750 |
10.2 |
5.0/5.0 |
3.6/3.2 |
1.6 |
165 |
$1,376 |
|
STD 96-2U* |
8' |
2550 |
5100 |
2-1/2 HP |
1750 |
10.2 |
5.0/5.0 |
3.6/3.2 |
1.6 |
170 |
$1,482 |
|
STD 96-3U* |
8' |
3825 |
7650 |
3-1/2 HP |
1750 |
15.3 |
7.5/7.5 |
5.4/4.8 |
2.4 |
200 |
$1,948 |
|
STD 108-2U* |
9' |
2550 |
5100 |
2-1/2 HP |
1750 |
10.2 |
5.0/5.0 |
3.6/3.2 |
1.6 |
180 |
$1,543 |
|
STD 108-3U* |
9' |
3400 |
7650 |
3-1/2 HP |
1750 |
15.3 |
7.5/7.5 |
5.4/4.8 |
2.4 |
210 |
$2,009 |
|
STD 120-3U* |
10' |
3060 |
7650 |
3-1/2 HP |
1750 |
15.3 |
7.5/7.5 |
5.4/4.8 |
2.4 |
225 |
$2,076 |
|
STD 144-3U* |
12' |
2550 |
7650 |
3-1/2 HP |
1750 |
15.3 |
7.5/7.5 |
5.4/4.8 |
2.4 |
240 |
$2,253 |
|
STD 144-4U* |
12' |
3400 |
10200 |
4-1/2 HP |
1750 |
20.4 |
10.0/10.0 |
7.2/6.4 |
3.2 |
270 |
$2,703 |
|
| *Add
Code for required voltage from chart above. |
|
|
|
|
 |
|
|
|
|
|
|
|
| Optional
Color Available - Std. Production Color is Battleship Gray
|
|
|
|
|
|
| Obsidian
Black - $20.00 per linear
foot (indicate OB after voltage code) |
|
| Pearl
White - $20.00 per linear
foot (indicate PW after voltage code) |
|
| Titanium
Silver - $20.00 per linear
foot (indicate TS after voltage code) |
|
| Spartan
Bronze - $20.00
per linear foot (indicate SB after voltage code) |
|
|
|
|
|
|
| Stainless
Steel - $167.00 per linear
foot (indicate SS after voltage code) |
|
|
|
|
STANDARD
SERIES ACCESSORIES - UNHEATED
MODELS
|
|
LEVEL 1 - CONTROL PACKAGE - LOW TRAFFIC DOORS |
|
LINE VOLTAGE CONTROL |
|
Part No. |
Package |
Price |
|
99-014 |
Door Limit Switch - Both Plunger & Roller all-in-one 20
amps, up to 250v, up 1 HP |
$66.60 |
|
24 VOLT CONTROL |
|
Part No. |
Package |
Price |
|
J0036 |
Industrial Magnetic Reed Switch with Controller (115v) up to
1 HP Magnetic reed switch with Controller |
$144.30 |
|
J0037 |
Industrial Magnetic Reed Switch with Controller (208/230v) up
to 1 HP Magnetic reed switch
with Controller (RIB) |
$144.30 |
|
99-081 |
Industrial Magnetic Reed Switch (only) Used in conjunction with
J0036 or J0037 for double doors
or w/control panel |
$33.30 |
|
99-017 |
Magnetic Floor Mounted Reed Switch - Used with control panel |
$77.70 |
|
LEVEL 2 - CONTROL PACKAGE - HIGH TRAFFIC DOORS (RECOMMENDED) |
|
24 VOLT CONTROL
|
|
Part No. |
Package |
Price |
|
J0038 |
Industrial Magnetic Reed switch, Adj. Time Delay Control (115v)
up to 1 HP Magnetic reed switch,
Controller, & Adjustable Time Delay (6 sec-20 min) (RIB) |
$177.60 |
|
J0042 |
Industrial Magnetic Reed switch, Adj. Time Delay Control (208/230v)
up to 1 HP Magnetic reed switch,
Controller, & Adjustable Time Delay (6 sec-20 min) (RIB) |
$177.60 |
|
99-081 |
Additional Industrial Magnetic Reed Switch (only) Used in conjuction
with J0038 or J0042 for double
doors or w/control panel |
$33.30 |
|
J0028 |
Door Limit Switch, Adj. Time Delay Control (115v) up to 1 HP
Door limit switch, controller &
adjustable time delay (6 sec-20 min) (RIB) |
$222.00 |
|
J0029 |
Door Limit Switch, Adj. Time Delay Control (2085/230v) up to
1 HP Door limit switch, controller &
adjustable time delay (6 sec-20 min) (RIB) |
$222.00 |
|
J0039 |
Magnetic Floor Mounted Reed Switch with Adj. Time Delay (1 sec-17
min) - Used with control panel |
$222.00 |
|
OPTIONAL CONTROLS - Can be paired with any control package
(Remote mounted in NEMA 1 J-Box) |
|
Part No. |
Package |
Price |
|
99-003 |
3-Speed Remote Selector Switch - Off/Lo/Med/Hi 15 amps-up to
1/2 HP Single Phase |
$55.50 |
|
99-033 |
2-Speed Hi/Lo Remote Switch (On/On) 15 amps - up to 1 HP Single
Phase |
$55.50 |
|
99-002 |
3-Speed Hi/Lo Remote Switch (On/Off/On) 25 amps - up to 1 HP
Single Phase |
$94.35 |
|
|
 |
|
|
|
|
|
|
MOTOR CONTROL PANELS-NEMA 1 (Control Panel Configuration) |
All
3 Phase Motors or Single Phase combined motors greater than
1 HP, over 250VAC, or greater than 20 amps require a motor
control panel whenever a door limit switch is used to start
and stop the air curtain. A door limit switch may be used to
directly
control one 1 HP or up to two 1/2 HP single phase motors without
the need for a motor control panel (not to exceed 20 amps or
250VAC) |
|
Part No. |
Description |
Price |
|
MCPA-1U* |
One Motor Control Panel 1/2 HP - specify required voltage |
$455.10 |
|
MCPA-2U* |
Two Motor Control Panel 1/2 HP - specify required voltage |
$849.15 |
|
MCPA-3U* |
Three Motor Control Panel 1/2 HP - specify required voltage |
$1,021.20 |
|
MCPA-4U* |
Four Motor Control Panel 1/2 HP - specify required voltage |
$1,209.90 |
|
MCPA-5U* |
Five Motor Control Panel 1/2 HP - specify required voltage |
$1,542.90 |
|
MCPA-6U* |
Six Motor Control Panel 1/2 HP - specify required voltage |
$1,842.60 |
|
| *Add
code for required voltage from chart above. |
|
|
|
|
PANEL ADDERS |
|
Part No. |
Package |
Price |
|
94-013 |
Adjustable Time-Delay (1 sec-17 min) control panel required |
$194.25 |
|
N-FUS |
Adder for panels with non-fused disconnect |
$333.00 |
|
FUS-30 |
Adder for panels with fused disconnect up to 30 amps - refer
to corresponding submittals |
$693.75 |
|
FUS-60 |
Adder for panels with fused disconnect up to 30 amps - 60 amps
- refer to corresponding submittals |
$832.50 |
|
MCP-MTD |
Factory Mounted Panel |
$249.75 |
|
|
|
|
MOUNTING BRACKETS
|
|
Part No. |
Mounting Bracket |
Price |
| Units
have flange on either end for easy overhead or back mounting. |
|
J0016 |
5" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0017 |
7" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0018 |
9" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0004 |
2 1/2" Clearance Mounting Bracket - to clear wall obstructions |
$55.50/set |
|
J0005 |
4" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0006 |
7" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0007 |
10" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0008G |
10" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$155.40/set |
|
J0009G |
16" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$155.40/set |
|
J0010G |
19" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$177.60/set |
|
J0011G |
23" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$177.60/set |
|
| *Consult
us for vertical mount |
|
|
|
|
FILTERS |
|
Part No. |
Filters |
Price |
|
FIL-(size) |
Aluminum Mesh (1/4") - indicate size in inches |
$8.88/ft. |
|
| *Please
cosult us for various flat bank and V bank filters. |
|
|
|
 |
 |
|
|
|
|
|
|
|
PRICING
FOR HIGH VELOCITY SERIES - UNHEATED
|
|
MODELS |
LENGTH |
FPM AT
NOZZLE |
CFM AT
NOZZLE |
MOTORS |
FLA (AMPACITY)
SINGLE PHASE |
FLA (AMPACITY)
THREE PHASE |
SHIP
WT
(LBS) |
PRICE |
|
HP |
RPM |
115V |
208V 230V |
208V 230V |
460V |
|
HV 42-1U* |
3' 6" |
4570 |
4000 |
1 HP |
1750 |
9.0 |
5.0/5.0 |
3.3/3.2 |
1.6 |
125 |
$1,088 |
|
HV 48-1U* |
4' |
4000 |
4000 |
1 HP |
1750 |
9.0 |
5.0/5.0 |
3.3/3.2 |
1.6 |
130 |
$1,099 |
|
HV 60-1U* |
5' |
3200 |
4000 |
1 HP |
1750 |
9.0 |
5.0/5.0 |
3.3/3.2 |
1.6 |
140 |
$1,121 |
|
HV 72-2U* |
6' |
5140 |
8000 |
2-1 HP |
1750 |
18.0 |
10.0/10.0 |
6.6/6.4 |
3.2 |
300 |
$2,031 |
|
HV 84-2U* |
7' |
4570 |
8000 |
2-1 HP |
1750 |
18.0 |
10.0/10.0 |
6.6/6.4 |
3.2 |
320 |
$2,165 |
|
HV 96-2U* |
8' |
4000 |
8000 |
2-1 HP |
1750 |
18.0 |
10.0/10.0 |
6.6/6.4 |
3.2 |
325 |
$2,220 |
|
HV 96-3U* |
8' |
4600 |
10000 |
3-1 HP |
1750 |
27.0 |
15.0/15.0 |
9.9/9.6 |
4.8 |
405 |
$2,614 |
|
HV 108-2U* |
9' |
3555 |
8000 |
2-1 HP |
1750 |
18.0 |
10.0/10.0 |
6.6/6.4 |
3.2 |
335 |
$2,281 |
|
HV 108-3U* |
9' |
4800 |
12000 |
3-1 HP |
1750 |
27.0 |
15.0/15.0 |
9.9/9.6 |
4.8 |
410 |
$2,686 |
|
HV 120-2U* |
10' |
3200 |
8000 |
2-1 HP |
1750 |
18.0 |
10.0/10.0 |
6.6/6.4 |
3.2 |
350 |
$2,325 |
|
HV 120-3U* |
10' |
4800 |
12000 |
3-1 HP |
1750 |
27.0 |
15.0/15.0 |
9.9/9.6 |
4.8 |
425 |
$2,736 |
|
HV 144-3U* |
12' |
4000 |
12000 |
3-1 HP |
1750 |
27.0 |
15.0/15.0 |
9.9/9.6 |
4.8 |
450 |
$2,925 |
|
HV 144-4U* |
12' |
5140 |
16000 |
4-1HP |
1750 |
36.0 |
20.0/20.0 |
13.2/12.8 |
6.4 |
480 |
$3,530 |
|
| *Add
code for required voltage from chart above. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Optional
Color Available - Std. Production Color is Battleship Gray
|
|
|
|
|
|
| Obsidian
Black - $20.00 per linear
foot (indicate OB after voltage code) |
|
| Pearl
White - $20.00 per linear
foot (indicate PW after voltage code) |
|
| Titanium
Silver - $20.00 per linear
foot (indicate TS after voltage code) |
|
| Spartan
Bronze - $20.00
per linear foot (indicate SB after voltage code) |
|
|
|
|
|
|
| Stainless
Steel - $167.00 per linear
foot (indicate SS after voltage code) |
|
|
|
|
HIGH
VELOCITY SERIES ACCESSORIES - UNHEATED
|
|
LEVEL 1 CONTROL PACKAGE - Low Traffic Doors |
|
LINE VOLTAGE |
|
Part No. |
Package |
Price |
|
99-014 |
Door Limit Switch - Both Plunger & Roller all-in-one 20
amps, up to 250v, up 1 HP |
$66.60 |
|
24 VOLT CONTROL |
|
Part No. |
Package |
Price |
|
99-081 |
Industrial Magnetic Reed Switch - control panel required |
$33.30 |
|
99-017 |
Floor Mounted Magnetic Reed Switch - control panel required |
$77.70 |
|
|
|
LEVEL 2 - CONTROL PACKAGE - High Traffic Doors (RECOMMENDED) |
|
LINE VOLTAGE |
|
Part No. |
Package |
Price |
|
J0034 |
Door Limit Switch with Adjustable Time Delay (1 sec-17 min)
panel required |
$222.00 |
|
|
|
24 VOLT CONTROL
|
|
Part No. |
Package |
Price |
|
J0040 |
Industrial Magnetic Reed Switch with Adjustable Time Delay (1
sec-17 min) control panel required |
$222.00 |
|
J0039 |
Floor Mounted Magnetic Reed Switch with Adjustable Time Delay
(1 sec-17 min) control
panel required |
$222.00 |
|
|
|
OPTIONAL CONTROLS - Can be paired with any control package (Remote
mounted in NEMA 1 J-Box) |
|
Part No. |
Package |
Price |
|
99-033 |
2-Speed Hi/Lo Remote Switch (On/On) 15 amps - up to 1 HP Single
Phase |
$55.50 |
|
99-002 |
2-Speed Hi/Lo Remote Switch (On/Off/On) 25 amps - up to 1 HP
Single Phase |
$94.35 |
|
|
|
 |
|
|
|
|
MOTOR CONTROL PANELS-NEMA 1 (Control Panel Configuration) |
All
3 Phase Motors or Single Phase combined motors greater than
1 HP, over 250VAC, or greater than 20 amps require a motor
control panel whenever a door limit switch is used to start
and stop the air curtain. A door limit switch may be used to
directly
control one 1 HP or up to two 1/2 HP single phase motors without
the need for a motor control panel (not to exceed 20 amps or
250VAC) |
|
Part No. |
Description |
Price |
|
MCPA-1U* |
One Motor Control Panel 1/2 HP - specify required voltage |
$455.10 |
|
MCPA-2U* |
Two Motor Control Panel 1/2 HP - specify required voltage |
$849.15 |
|
MCPA-3U* |
Three Motor Control Panel 1/2 HP - specify required voltage |
$1,021.20 |
|
MCPA-4U* |
Four Motor Control Panel 1/2 HP - specify required voltage |
$1,209.90 |
|
MCPA-5U* |
Five Motor Control Panel 1/2 HP - specify required voltage |
$1,542.90 |
|
MCPA-6U* |
Six Motor Control Panel 1/2 HP - specify required voltage |
$1,842.60 |
|
| *Add
code for required voltage from chart above |
|
|
|
|
PANEL ADDERS |
|
Part No. |
Package |
Price |
|
94-013 |
Adjustable Time-Delay (1 sec-17 min) control panel required |
$194.25 |
|
N-FUS |
Adder for panels with non-fused disconnect |
$333.00 |
|
FUS-30 |
Adder for panels with fused disconnect up to 30 amps - refer
to corresponding submittals |
$693.75 |
|
FUS-60 |
Adder for panels with fused disconnect up to 30 amps - 60 amps
- refer to corresponding submittals |
$832.50 |
|
MCP-MTD |
Factory Mounted Panel |
$249.75 |
|
|
|
|
MOUNTING BRACKETS
|
|
Part No. |
Mounting Bracket |
Price |
| Units
have flange on either end for easy overhead or back mounting. |
|
J0016 |
5" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0017 |
7" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0018 |
9" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0004 |
2 1/2" Clearance Mounting Bracket - to clear wall obstructions |
$55.50/set |
|
J0005 |
4" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0006 |
7" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0007 |
10" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0008G |
10" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$155.40/set |
|
J0009G |
16" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$155.40/set |
|
J0010G |
19" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$177.60/set |
|
J0011G |
23" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$177.60/set |
|
| *Consult
us for vertical mount |
|
|
|
|
FILTERS |
|
Part No. |
Filters |
Price |
|
FIL-(size) |
Aluminum Mesh (1/4") - indicate size in inches |
$8.88/ft. |
|
| *Please
cosult us for various flat bank and V bank filters. |
|
 |
|
|
|
 |
|
|
|
PRICING
FOR EXTRA POWER MODELS SERIES - UNHEATED
|
|
MODELS |
LENGTH |
FPM AT
NOZZLE |
CFM AT
NOZZLE |
MOTORS |
FLA (AMPACITY)
SINGLE PHASE |
FLA (AMPACITY)
THREE PHASE |
SHIP
WT
(LBS) |
PRICE |
|
HP |
RPM |
115V |
208V 230V |
208V 230V |
460V |
|
EP 48-1U* |
4' |
4800 |
4800 |
3 HP |
3450 |
30.0 |
16.5/15.0 |
8.3/7.6 |
3.8 |
130 |
$1,210 |
|
EP 60-1U* |
5' |
3840 |
4800 |
3 HP |
3450 |
30.0 |
16.5/15.0 |
8.3/7.6 |
3.8 |
140 |
$1,271 |
|
EP 72-2U* |
6' |
6100 |
9600 |
2-3 HP |
3450 |
60.0 |
33.0/30.0 |
16.5/15.2 |
7.6 |
300 |
$2,387 |
|
EP 84-2U* |
7' |
5485 |
9600 |
2-3 HP |
3450 |
60.0 |
33.0/30.0 |
16.5/15.2 |
7.6 |
320 |
$2,442 |
|
EP 96-2U* |
8' |
4800 |
9600 |
2-3 HP |
3450 |
60.0 |
33.0/30.0 |
16.5/15.2 |
7.6 |
325 |
$2,498 |
|
EP 108-2U* |
9' |
4200 |
9600 |
2-3 HP |
3450 |
60.0 |
33.0/30.0 |
16.5/15.2 |
7.6 |
335 |
$2,592 |
|
EP 108-3U* |
9' |
4800 |
12800 |
3-3 HP |
3450 |
90.0 |
49.5/45.0 |
24.9/22.8 |
11.4 |
410 |
$3,091 |
|
EP 120-2U* |
10' |
3840 |
9600 |
2-3 HP |
3450 |
60.0 |
33.0/30.0 |
16.6/15.2 |
7.6 |
350 |
$2,658 |
|
EP 120-3U* |
10' |
5760 |
14400 |
3-3 HP |
3450 |
90.0 |
49.5/45.0 |
24.9/22.8 |
11.4 |
425 |
$3,164 |
|
EP 144-3U* |
12' |
4800 |
14400 |
3-3 HP |
3450 |
90.0 |
49.5/45.0 |
24.9/22.8 |
11.4 |
450 |
$3,275 |
|
| *Add
code for required voltage from chart above |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Optional
Color Available - Std. Production Color is Battleship Gray
|
|
|
|
|
|
| Obsidian
Black - $20.00 per linear
foot (indicate OB after voltage code) |
|
| Pearl
White - $20.00 per linear
foot (indicate PW after voltage code) |
|
| Titanium
Silver - $20.00 per linear
foot (indicate TS after voltage code) |
|
| Spartan
Bronze - $20.00
per linear foot (indicate SB after voltage code) |
|
|
|
|
|
|
| Stainless
Steel - $167.00 per linear
foot (indicate SS after voltage code) |
|
|
|
|
EXTRA
POWER SERIES ACCESSORIES - UNHEATED
|
|
LEVEL 1 CONTROL PACKAGE - Low Traffic Doors |
|
LINE VOLTAGE |
|
Part No. |
Package |
Price |
|
99-014 |
Door Limit Switch - Both Plunger & Roller all-in-one 20
amps, up to 250v, up 1 HP |
$66.60 |
|
24 VOLT CONTROL |
|
Part No. |
Package |
Price |
|
99-081 |
Industrial Magnetic Reed Switch - control panel required |
$33.30 |
|
99-017 |
Floor Mounted Magnetic Reed Switch - control panel required |
$77.70 |
|
|
|
LEVEL 2 - CONTROL PACKAGE - High Traffic Doors (RECOMMENDED) |
|
LINE VOLTAGE |
|
Part No. |
Package |
Price |
|
J0034 |
Door Limit Switch with Adjustable Time Delay (1 sec-17 min)
panel required |
$222.00 |
|
|
|
24 VOLT CONTROL
|
|
Part No. |
Package |
Price |
|
J0040 |
Industrial Magnetic Reed Switch with Adjustable Time Delay (1
sec-17 min) control panel required |
$222.00 |
|
J0039 |
Floor Mounted Magnetic Reed Switch with Adjustable Time Delay
(1 sec-17 min) control
panel required |
$222.00 |
|
|
|
OPTIONAL CONTROLS - Can be paired with any control package (Remote
mounted in NEMA 1 J-Box) |
|
Part No. |
Package |
Price |
|
99-033 |
2-Speed Hi/Lo Remote Switch (On/On) 15 amps - up to 1 HP Single
Phase |
$55.50 |
|
99-002 |
2-Speed Hi/Lo Remote Switch (On/Off/On) 25 amps - up to 1 HP
Single Phase |
$94.35 |
|
|
|
 |
|
|
|
|
MOTOR CONTROL PANELS-NEMA 1 (Control Panel Configuration) |
All
3 Phase Motors or Single Phase combined motors greater than
1 HP, over 250VAC, or greater than 20 amps require a motor
control panel whenever a door limit switch is used to start
and stop the air curtain. A door limit switch may be used to
directly
control one 1 HP or up to two 1/2 HP single phase motors without
the need for a motor control panel (not to exceed 20 amps or
250VAC) |
|
Part No. |
Description |
Price |
|
MCPA-1U* |
One Motor Control Panel 1/2 HP - specify required voltage |
$455.10 |
|
MCPA-2U* |
Two Motor Control Panel 1/2 HP - specify required voltage |
$849.15 |
|
MCPA-3U* |
Three Motor Control Panel 1/2 HP - specify required voltage |
$1,021.20 |
|
MCPA-4U* |
Four Motor Control Panel 1/2 HP - specify required voltage |
$1,209.90 |
|
MCPA-5U* |
Five Motor Control Panel 1/2 HP - specify required voltage |
$1,542.90 |
|
MCPA-6U* |
Six Motor Control Panel 1/2 HP - specify required voltage |
$1,842.60 |
|
| *Add
code for required voltage from chart above. |
|
|
|
|
PANEL ADDERS |
|
Part No. |
Package |
Price |
|
94-013 |
Adjustable Time-Delay (1 sec-17 min) control panel required |
$194.25 |
|
N-FUS |
Adder for panels with non-fused disconnect |
$333.00 |
|
FUS-30 |
Adder for panels with fused disconnect up to 30 amps - refer
to corresponding submittals |
$693.75 |
|
FUS-60 |
Adder for panels with fused disconnect up to 30 amps - 60 amps
- refer to corresponding submittals |
$832.50 |
|
MCP-MTD |
Factory Mounted Panel |
$249.75 |
|
|
|
|
MOUNTING BRACKETS
|
|
Part No. |
Mounting Bracket |
Price |
| Units
have flange on either end for easy overhead or back mounting. |
|
J0016 |
5" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0017 |
7" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0018 |
9" Side Extension Plates - to clear track on either end |
$77.70/set |
|
J0004 |
2 1/2" Clearance Mounting Bracket - to clear wall obstructions |
$55.50/set |
|
J0005 |
4" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0006 |
7" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0007 |
10" Clearance Mounting Bracket - to clear wall obstructions |
$77.70/set |
|
J0008G |
10" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$155.40/set |
|
J0009G |
16" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$155.40/set |
|
J0010G |
19" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$177.60/set |
|
J0011G |
23" Clearance Extended Wall Mouting Bracket - drum style
roll-up doors |
$177.60/set |
|
| *Consult
us for vertical mount |
|
|
|
|
FILTERS |
|
Part No. |
Filters |
Price |
|
FIL-(size) |
Aluminum Mesh (1/4") - indicate size in inches |
$8.88/ft. |
|
| *Please
cosult us for various flat bank and V bank filters. |
|
|
|
1/2
HP STANDARD UNHEATED MODELS DRAWING
|
|
|
|
|
|
|
|
NOTES: |
|
|
|
1.
This product is designed to comply with the National
Electric Code (NEC) ETL listed for US & Canada,
and
bear the CE mark. |
|
 |
|
| 2.
7/16" mounting holes (4) provided, (2) on each end. |
|
3.
All units have a self contained one piece cabinet, fire
retardant and corrosion proof pain lock metal,
double
protected with baked on gray color rust preventative
electrostatic polyurethane powder coating. |
|
4.
Cabinet has sufficient strength for fastening to wall on
both ends without intermediate support. |
|
| 5.
Internal J-Box(ex) for electrical wiring. |
|
6.
Unit is to be installed such that air flow is unobstructed.
Air discharge nozzle containing adjustable air
directional
vanes with 40° sweep front to back. |
|
 |
|
|
|
7.
Optional motor control panel. Overloads are factory set.
Standard procedure is to ship panel loose for remote
mount. Can be factory mounted on either left or
right hand
side of air curtain housing. Please specify. |
|
|
8.
Circuit protection as per NEC by others. |
|
|
9.
Optional microswitch is field installed and is to be wired
to the control panel. Switch to be
mounted such that the
air curtain turns on as door begins
to open. |
|
|
|
|
|
|
|
|
|
|
| -2,
-3 & -4 designates the number of motors. |
|
|
|
|
|
*NOTE:
Louver assembly size and number varies with length. |
|
Model No. |
Mounting Centers A |
Length B |
|
STD 36-1U |
35 1/8" |
36" |
|
STD 42-1U |
41 1/8" |
42" |
|
STD 48-1U |
47 1/8" |
48" |
|
STD 64-2U |
63 1/8" |
64" |
|
STD 72-2U |
71 1/8" |
72" |
|
STD 78-2U |
77 1/8" |
78" |
|
STD 84-2U |
83 1/8" |
84" |
|
STD 96-2U |
95 1/8" |
96" |
|
STD 96-3U |
95 1/8" |
96" |
|
STD 108-2U |
107 1/8" |
108" |
|
STD 108-3U |
107 1/8" |
108" |
|
STD 120-3U |
119 1/8" |
120" |
|
STD 144-3U |
143 1/8" |
144" |
|
STD 144-4U |
143 1/8" |
144" |
|
|
|
|
|
|
|
 |
|
TYPICAL
INSTALLATION
|
|
|
1.
Connect supply voltage
from power panel to control
panel. (8) |
|
|
2.
Connect wires from motor
leads in junction box to
terminals in panel per print. |
|
|
3.
Connect wires from micro
switch to terminals in
panel per print. |
|
|
4.
Check rotation of motors
and switch leads if
necessary to correct. |
|
|
|
|
|
|
|
|
 |
|
|
|
1
HP HIGH VELOCITY UNHEATED MODELS DRAWING
|
|
|
|
|
 |
NOTES: |
|
1.
This product is designed to comply with the
National Electric Code (NEC) ETL listed for US
& Canada, and bear the CE mark. |
|
| 2.
7/16" mounting holes (4) provided, (2) on each end. |
|
3.
All units have a self contained one piece cabinet, fire
retardant and corrosion proof paint lock metal,
double
protected with baked on gray color rust preventative
electrostatic polyurethane powder coating. |
|
4.
Cabinet has sufficient strength for fastening to
wall on both ends without intermediate support. |
|
| 5.
Internal J-Box(es) for electrical wiring. |
|
6.
Units is to be installed such that air flow is
unobstructed. Air discharge nozzle containing
adjustable air directional vanes with 40° sweep
front to back. |
|
7.
Optional motor control panel. Overloads are
factory set. Standard procedure is to ship
panel loose for remote mount. Can be factory
mounted on either left or right hand side of air
curtain housing. Please specify. |
|
|
|
|
8.
Circuit protection as per NEC by others. |
|
|
9.
Optional microswitch is field installed and is to
be wired to the control panel. Switch to be
mounted such that the air curtain turns on as
door begins to open. |
|
|
|
|
|
|
|
| -2
& -3 designates the number of motors. |
|
|
*NOTE:
Louver assembly size and number varies with unit
length. |
| Model
No. |
Mounting
Centers A |
Overall
Length B |
| HV
42-1U |
41 1/8" |
42" |
| HV
48-1U |
47 1/8" |
48" |
| HV
60-1U |
59 1/8" |
60" |
| HV
72-2U |
71 1/8" |
72" |
| HV
84-2U |
83 1/8" |
84" |
| HV
96-2U |
95 1/8" |
96" |
| HV
96-3U |
95 1/8" |
96" |
| HV
108-2U |
107 1/8" |
108" |
| HV
108-3U |
107 1/8" |
108" |
| HV120-2U |
119 1/8" |
120" |
| HV
120-3U |
119 1/8" |
120" |
| HV
144-3U |
143 1/8 |
144" |
| HV
144-4U |
143 1/8 |
144" |
|
|
|
|
|
|
|
|
|
|
|
TYPICAL
INSTALLATION
|
|
|
|
1.
Connect supply voltage
from power panel to
control panel. (8) |
|
|
|
2.
Connect wires from
motor leads in junction
box to terminals in panel
per print. |
|
|
|
3.
Connect wires from
micro switch to terminals
in panel per print. |
|
|
|
4.
Check rotation of motors
and switch leads if
necessary to correct. |
|
|
|
|
|
|
|
|
|
|
|
|
|
3
HP EXTRA POWER UNHEATED MODELS
|
|
|
|
 |
|
NOTES: |
|
1.
This product is designed to comply with the
National Electric Code (NEC) ETL listed for US
& Canada, and bear the CE mark. |
|
2.
7/16" mounting holes (4) provided, (2) on each end. |
|
3.
All units have a self contained one piece cabinet, fire
retardant and corrosion proof paint lock metal,
double
protected with baked on gray color rust preventative
electrostatic polyurethane powder coating. |
|
4.
Cabinet has sufficient strength for fastening to
wall on both ends without intermediate support. |
|
5.
Internal J-Box(es) for electrical wiring. |
|
6.
Units is to be installed such that air flow is
unobstructed. Air discharge nozzle containing
adjustable air directional vanes with 40° sweep
front to back. |
|
7.
Optional motor control panel. Overloads are
factory set. Standard procedure is to ship
panel loose for remote mount. Can be factory
mounted on either left or right hand side of air
curtain housing. Please specify. |
|
|
|
|
8.
Circuit protection as per NEC by others. |
|
|
9.
Optional microswitch is field installed and is to
be wired to the control panel. Switch to be
mounted such that the air curtain turns on as
door begins to open. |
|
|
|
|
|
|
| -2
& -3 designates the number of motors. |
|
|
|
|
|
|
|
*NOTE:
Louver assembly size and quantity varies with unit
length. |
MODEL
NUMBER |
MOUNTING
CENTERS A |
OVERALL
LENGTH B |
|
EP48-1U |
47 1/8" |
48" |
|
EP60-1U |
59 1/8" |
60" |
|
EP72-2U |
71 1/8" |
72" |
|
EP84-2U |
83 1/8" |
84" |
|
EP96-2U |
95 1/8" |
96" |
|
EP108-2U |
107 1/8" |
108" |
|
EP108-3U |
107 1/8" |
108" |
|
EP120-2U |
119 1/8" |
120" |
|
EP120-3U |
119 1/8" |
120" |
|
EP144-3U |
143 1/8" |
144" |
|
|
|
|
|
|
|
|
|
|
|
|
TYPICAL
INSTALLATION
|
|
|
|
1.
Connect supply voltage
from power panel to control
panel. (8) |
|
|
|
2.
Connect wires from motor
leads in junction box to
terminals in panel per print. |
|
|
|
3.
Connect wires from micro
switch to terminals in panel
per print. |
|
|
|
4.
Check rotation of motors
and switch leads if necessary
to correct. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TYPICAL
INSTALLATION OF METAL AIR CURTAINS
FOR DRUM TYPE ROLL-UP DOORS
|
|
 |
|
|
TYPICAL
INSTALLATION FOR VERTICAL LIFT TRACK DOORS
|
|
 |
|
|
|
TYPICAL
INSTALLATION FOR OVERHEAD MOUNTING
|
|
|
|
|
 |
|
|
Air Curtain, Air Curtain
Door, Air Curtain Heater, Air Curtains, Air Doors, Door Air Curtains,
Heat Curtains, Mars Air Curtain,
Mars Air Door, Warm Air Curtains, and Insect Barrier from your source
for material handling equipment.
|
Back to Product Category
|
